Impex Marcy Diamond MD-859 Manual de usuario
MARCY DIAMOND
WEIGHT BENCH
MD-859
IMPEX®INC.
14777 Don Julian Rd., City of Industry, CA 91746
Tel: (800) 999-8899 Fax (626) 961-9966
www.impex-fitness.com
NOTE:
Please read all
instructions carefully
before using this product
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
MD-859
Retain This
Manual for
Reference
09/25/08
OWNER'S
MANUAL
TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICE....................................................................... 2
HARDWARE PACK………............................................................................... 4
ASSEMBLY INSTRUCTIONS........................................................................... 5
EXPLODED DIAGRAM.................................................................................... 10
PARTS LIST..................................................................................................... 11
WARRANTY..................................................................................................... 12
ORDERING PARTS.......................................................................................... 12
BEFORE YOU BEGIN
Thank you for selecting the MARCY DIAMOND WEIGHT BENCH MD-859 by
IMPEX®INC. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there
are missing or damaged parts, we guarantee your complete satisfaction
through direct assistance from our factory. To avoid unnecessary delays,
please call our TOLL-FREE customer service number. Our Customer
Service Agents will provide immediate assistance to you.
1
Toll-Free Customer Service Number
1-800-999-8899
Mon. - Fri. 9 a.m. - 5 p.m. PST
www.impex-fitness.com
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave children
unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water or
outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or other
clothing that could become caught in the machine. Running or aerobic shoes are also
required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Maximum user’s weight: 300 lbs.
14. Maximum weight on uprights: 600 lbs.
15. Maximum weight on leg developer: 100 lbs.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE
OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
WARNING LABEL REPLACEMENT
The Warning Labels shown here have been placed on the Rear Base Frame and Rear
Stabilizer. If the labels are missing or illegible, please call customer service at 1-800-999-
8899 for replacement. Apply the labels in location shown
3
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4
ASSEMBLY INSTRUCTION
Tools Required For Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended for two or more people to assemble this
machine to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Attach one Base Frame (#3) to the Rear Base Frame (#2). Attach an Upright Beam (#1)
onto the Base Frame and Rear Base Frame. Secure them together with two M10 x 3
5/8” Carriage Bolts (#32), one 5 ½” x 2” Bracket (#15), two Ø ¾” Washer (#41), and two
M10 Aircraft Nuts (#44) from bottom. Secure with two M10 x 2 ¾” Carriage Bolts (#33),
two Ø ¾” Washer (#41), and two M10 Aircraft Nuts (#44) from side. Do not tighten the
Nuts and Bolts yet. Repeat the same procedure to install the other side.
B.)Securely tighten all Nuts and Bolts.
C.)Insert two Crutches (#4) into the two Upright Beams. Insert two M18 Lock Knobs (#19)
through the selected holes to obtain desired height. DIAGRAM 1
5
STEP 2 (See Diagram 2)
A.) Attach the Main Seat Support (#5) to the Rear Stabilizer (#6). Secure it with two M10 x 2
¾” Carriage Bolts (#33), one 5 1/8” x 2 ¾” Bracket (#14), two Ø ¾” Washers (#41), and
two M10 Aircraft Nuts (#44).
B.) Attach the two Incline Support Frames (#12) to the Main Seat Support. Secure them to the
Main Seat Support with three M10 x 3 5/8” Allen Bolts (#35), six Ø ¾” Washers (#41), and
three M10 Aircraft Nuts (#44). DIAGRAM 2
6
STEP 3 (See Diagram 3)
A.) Attach the pivot on the Leg Developer Holder (#7) to the open bracket on the Main Seat
Support (#5). Attach the bottom of Leg Developer Holder to the Main Seat Support.
Secure it with one M10 x 2 ¾” Carriage Bolt (#33) from front, one M10 x 2 ½” Allen Bolt
(#37) from rear, two Ø ¾” Washers (#41), and one M10 Aircraft Nut (#44).
B.) Attach the Incline Support (#9) to the side-holes on the two Backrest Supports (#8). Align
the holes. Secure it with one M10 x 5 ½” Allen Bolt (#34), two Ø ¾” Washers (#41), and
one M10 Aircraft Nut (#44).
C.) Attach the holes on the end of the Backrest Supports (#12) to the bracket on the Main
Seat Support. Align the holes. Secure the two Backrest Supports to the bracket, and the
pivot on Leg Developer Holder together with one M12 x 5 ¾” Hex Bolt (#31), two Ø 1”
Washers (#41), and one M12 Aircraft Nut (#44).
D.) Do not over tighten the Nuts and Bolts. Make sure the Backrest Supports and Backrest
Incline are able to swivel.
E.) Place the other ends of Incline Support onto the selected slot on Incline Support Frames
(#12) to hold the Backrest Incline in position. DIAGRAM 3
7
STEP 4 (See Diagram 4)
A.) Attach the Backrest Board (#17) to the Backrest Supports (#8). Secure it with four M8 x 1
5/8” Allen Bolts (#38) and four Ø 5/8” Washers (#42).
B.) Place the Seat Pad (#16) onto the seat bracket on Leg Developer Holder (#7). Secure it
with one M8 x 1 5/8” Allen Bolts (#38), two M8 x 5/8” Allen Bolts (#3), and two Ø 5/8”
Washers (#42). DIAGRAM 4
8
STEP 5 (See Diagram 5)
A.) Attach two Ø 5/8” Bushings (#20) to the Leg Developer (#10). Attach the Leg Developer
to the Leg Developer Holder (#7). Secure it with one M10 x 3 1/8” Allen Bolt (#36), two Ø
¾” Washers (#41), and one M10 Aircraft Nut (#44).
B.) Insert three Foam Tubes (#13) halfway through the holes on the Leg Developer and Leg
Developer Holder. Push six Foam Rolls (#27) onto the Tubes from both ends. Plug six
Foam Roll End Caps (#26) into the ends.
C.) Slide an Olympic Sleeve (#29) onto the weight post on Leg Developer. Attach a Spring
Clip (#30) onto the Sleeve.
D.) Attach the Arm Curl Pad (#18) to the Arm Curl Stand (#11). Secure it with two M8 x 5/8”
Allen Bolts (#39) and two Ø 5/8” Washers (#42).
E.) Insert the Arm Curl Stand into the Leg Developer holder. Use the M10 Lock Knob (#28) to
lock the Arm Curl Stand in position.
F.) Remove the Arm Curl Stand when doing Leg Developer exercises. DIAGRAM 5
9
Tabla de contenidos
Otros manuales de Gimnasio en casa de Impex
Impex
Impex POWERHOUSE CLUB PWR 6 Manual de usuario
Impex
Impex GOLD'S GYM WMGG-368 Manual de usuario
Impex
Impex MARCY MD-11.0 Manual de usuario
Impex
Impex APEX WM-348.1 Manual de usuario
Impex
Impex MARCY CLUB MKM-81010 Manual de usuario
Impex
Impex SB 681 Manual de usuario
Impex
Impex MACH JD 3 Manual de usuario
Impex
Impex Circuit Fitness AMZ-986RW-BT Manual de usuario
Impex
Impex Iron Grip Sport IGS-01 Manual de usuario
Impex
Impex MWM-981 Manual de usuario
Impex
Impex MARCY DIAMOND ELITE SM-1050 Manual de usuario
Impex
Impex MARCY PRO SM-7409 Manual de usuario
Impex
Impex POWERHOUSE ELITE PHE1000 Manual de usuario
Impex
Impex Marcy MWM-4965 Manual de usuario
Impex
Impex IRON GRIP STRENGTH TSA-41 Manual de usuario
Impex
Impex Marcy Diamond Elite MD-PWR-20 Manual de usuario
Impex
Impex MARCY DIAMOND ELITE MD-9010G Manual de usuario
Impex
Impex MARCY MWB-70500 Manual de usuario
Impex
Impex MARCY PRO SM-4903 Manual de usuario
Impex
Impex MD-860 Manual de usuario
Manuales populares de Gimnasio en casa de otras marcas
Horizon Fitness
Horizon Fitness OXFORD 6 Manual de usuario
Energetics
Energetics Multi Trainer 5.1 Manual de usuario
Matrix
Matrix MG-PL Series Manual de usuario
Reebok
Reebok Tbr2i Manual de operación y mantenimiento
Weider
Weider 8300 Hard Drive Manual de usuario
Pure Fitness
Pure Fitness 8526HE Manual de usuario
