illunis EMC-51 Manual de usuario
Operations Manual
Advanced Digital Machine Vision Cameras
EMC
Embedded Machine Camera
EMC-51
EMC-65
EMC-103
EMC Operations Manual Copyright illunis, LLC 1/12/2023 Page 2
Revisions
EMC (51, 65, 103)
Rev Date Modification
A01/06/23 Initial Release
Camera Communication Default Baud Rate is 115,200
EMC Operations Manual Copyright illunis, LLC 1/12/2023 Page 3
Introduction
The EMC cameras based on the Gpixel GMAX sensors share a common FPGA and
Microprocessor firmware. The EMC case design is compact and light weight, making it ideal
for Arial and other embedded solutions.
Supported Sensors
• GMAX4651 : 8424x 6032 Global shutter, 3.2um pixel
• GMAX3265: 9344x7000 Global shutter, 3.2um pixel
• GMAX32103: 11,276x9200 Global shutter, 3.2um pixel
Supported Outputs
• Camera Link
• Epix mf2280 (Samtec HLCD)
• Pleora GigE
• Pleora USB3
• Pleora NTX-DECA (10G ethernet)
Note: All Output types may not be available for larger sensors.
Supported Lens Mounts
• Canon EF
• F-Mount
• M42
• M58
• OEM
Common features include:
Global Electronic Shutter
Horizontal and Vertical image flip
Vertical Subsampling and ROI
External triggering
12bit ADC with analog gain
Optical black clamp in FPGA
Low noise with excellent PLS
There are differences in the features of the supported sensors
GMAX4651 does not support VFlip
GMAX3265 does support dual exposure HDR mode
EMC Operations Manual Copyright illunis, LLC 1/12/2023 Page 4
Precautions
EMC (51, 65, 103)
EMC Precautions
Do not drop, damage, disassemble, immerse, repair or alter the
camera.
Applying incorrect power may damage the camera electronics.
The warranty is void if the camera is opened or modified in any
way.
Care must be taken in handling as not to create static dis-
charge that may permanently damage the device.
Camera Link is a DC based interface. The camera and capture
device must share the same electrical ground. Failure to do so
will damage the Camera Link interface chips and/or camera
and capture card.
PoCL cables are compatible with EMC Camera Link
cameras. PoCL camera power is not supported.
Absolute Maximum Ratings
Input Voltage: 7 to 14V DC
Storage Temperature: -40C to +70C
Recommended Maximum Ratings
Input Voltage: 7 to 14V DC
Operating Temperature: 0C to +70C
Most illunis cameras operate beyond these temperature limits,
please call for details.
Recommended Operating Conditions
Input Voltage: 9-12V DC
Operating Temperature: 0C to +70C
Relative humidity should not exceed 80% non-condensing.
Specifications subject to change without notice.
EMC Operations Manual Copyright illunis, LLC 1/12/2023 Page 5
Contents
EMC (51, 65, 103)
Table of Contents Page
Getting Started - Epix 6
Getting Started - GigE/USB3 7
Getting Started - Camera Link 8
Getting Started - Camera Link Serial 10
Getting Started - Camera Control App 14
Getting Started - Epix XCAP 23
Getting Started - Teledyne Dalsa Cam Expert 25
Camera Overview EMC-51 27
Camera Overview EMC-65 32
Camera Overview EMC-103 37
Hardware Overview 43
Serial Communication 48
Serial Commands 51
Gain and Black Level 53
Fast Meter and AE 56
Digital On Screen Display (DOSD) 57
Auto Exposure PBM 59
Command Details 62
Firmware Loader 66
Pixel, Row and Column Defects 68
Hot Pixel Correction 69
Shading Correction 71
Image Storage and Display 77
Camera Drawings 80
EMC Operations Manual Copyright illunis, LLC 1/12/2023 Page 6
Camera Power Epix
6-12V DC Power to the JST ZHR-7 connector.
View from Camera Back
Capture Card
Epix PIXCI® mf2280+
Imaging SDK
XCLIB™ Frame Grabber Programming Library (epixinc.com)
Camera Communication Software
illunis Camera Control Application Help Center – illunis
Data Cable
COTS Samtec HLCD
HLCD-20-XX-00-TR-TR-1 (XX = length in inches)
Digi-Key (other lengths available)
Getting Started Epix
EMC (51, 65, 103)
Power
7- Power
6- GND
5- Trigger In (LVTTL)
4- Strobe out (LVTTL)
3- GND
2- Power
1- Shell
EMC Operations Manual Copyright illunis, LLC 1/12/2023 Page 7
Camera Power GigE/USB3
6-12V DC Power to the Hirose 6 pin connector.
Mating Connector: Hirose HR10A-7P-6P
View from Camera Back
Capture Card
1 Gbps ethernet connection or compatible USB3 port.
Imaging SDK
Pleora SDK Pleora.com
Camera Communication Software
illunis Camera Control Application
Download at: Help Center – illunis
Getting Started GigE/USB3
EMC (51, 65, 103)
EMC Operations Manual Copyright illunis, LLC 1/12/2023 Page 8
Camera Power Camera Link
6-12V DC Power to the Hirose 6 pin connector.
Mating Connector: Hirose HR10A-7P-6P
View from Camera Back
Camera Power Pins 5 and 6 can be left unconnected for the fan cooled
version of the camera.
Capture Card
Any Base, Medium or Full Format Camera Link capture card
Such as: Teledyne Dalsa Xtium-CL MX4 OR-Y4CO-XMX00.
Imaging SDK
Available from your capture card supplier.
Camera Link Cables
One or two Camera Link cables (Mini HDR to SDR) must be
rated at 85Mhz or more (two cables for Medium or Full Format).
The following 5M cable configurations have been tested:
Standard MDR to HDR/SDR MVC-1-1-5-5M
Available from Components Express.
componentsexpress.com
Camera Communication Software
illunis Camera Control Application
Download at: illunis.com
Getting Started Camera Link
EMC (51, 65, 103)
EMC Operations Manual Copyright illunis, LLC 1/12/2023 Page 9
To start imaging with the EMC–CL:
Install the capture card and software per the capture card
manufacturers instructions.
Connect the EMC Camera Link cables paying attention to
the base and medium connections
Getting Started Camera Link
EMC (51, 65, 103)
Camera Link Medium mode setup
Blue cable = Base Mode Connection
Green cable = Medium/Full and Deca
Connection
Camera Link
Communication: CLA
A
Cable Connections for Camera Link Medium/Full and Deca
Mode Operation.
Base Mode uses only CLA Base Connection
EMC Operations Manual Copyright illunis, LLC 1/12/2023 Page 10
Camera Link Serial Overview
Download and install the illunis Camera Serial
Communication Software from
https://www.illunis.com
Background:
Per the CameraLink standard, all serial communication is via the .dll
clallserial.dll, which dynamically loads the serial communication .dll(s)
specific to the frame grabber being used. illunis installs clallserial.dll in
its application directory.
clallserial.dll examines the registry to see where the capture card
specific communication dll's have been installed. The naming
convention for the capture card specific communication dll's is
clser***.dll where *** is the manufacturer specific dll name. The files
MUST be in the form clser***.dll in order to be recognized. Some
capture card manufacturers will append something like clser***x64.dll
for the 64 bit version of the .dll. This file name must be changed to
clser***.dll in order to be recognized by clallserial.dll.
illunis camera
control app
clallserial.dll
clserxxx.dll clseryyy.dll clserzzz.dll
Getting Started Camera Link Serial
EMC (51, 65, 103)
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Cámara digital de illunis
