idi ilex Manual de usuario
Made in the USA L280-0974 REV C
Mobile Video Integration System
Installation Guide
For units using MSV2 video signal router
The text of this manual was originally written, approved and published by the manufacturer in English. The information and
images in this document are proprietary to IDI and is only for use for and by IDI representatives or their Agents.
Installation Guide
ilex
L280-0974 REV C www.imagediagnostics.com Page i
Table of Contents
ilex controls..................................................................................................................................... 1
Video Inputs.................................................................................................................................... 1
Factory Preset Layouts.................................................................................................................... 3
Accessing Onscreen Keyboard....................................................................................................... 5
Modifying Layouts.......................................................................................................................... 5
Assigning Channels to Window Location ...................................................................................... 7
Cropping Windows......................................................................................................................... 8
Rename Layouts and Channels....................................................................................................... 9
Saving and returning to guest mode................................................................................................ 9
Monitor Video Setting Menu Navigation..................................................................................... 10
Barco Monitor......................................................................................................................... 10
FSN Monitor ........................................................................................................................... 13
Installation Guide ilex
L280-0974 REV C www.imagediagnostics.com Page 1
ilex controls
For details of ilex cart and monitor controls, please refer to Operator Manual L280-0975.
Video Inputs
The ilex has 4 different channel input capabilities
Video inputs are connected to the rear of the ilex then routed scalers and into the controller, the MSV2
(Multiview scalar). Basic Layout navigation is done in the “Guest” mode of the system. Changing or
programing of the layout format is available only in the “Administrator” mode.
Video Panel on rear of ilex
Channel 1 inputs: DVI, VGA, or S-Video
Channel 2 inputs: DVI, or VGA or SDI(using DVI to DVI jumper from SDI panel)
Channel 3 inputs: DVI, DisplayPort, or SOG
Channel 4 inputs: DVI, DisplayPort, or SOG
Installation Guide ilex
L280-0974 REV C www.imagediagnostics.com Page 3
Factory Preset Layouts
By design each preset has the capability of showing 4 windows, A, B, C, & D. Each of the windows can be
cropped, resized, relocated, and assigned one of the 4 channel inputs. Channels 3 & 4 can also accept
DisplayPort video inputs when required. Channels 1 and 2 are HDMI inputs only.
There are 8 preset layouts as shown below. There is also single channel layout which displays each of the four
channels at full screen.
Installation Guide ilex
L280-0974 REV C www.imagediagnostics.com Page 5
Accessing Onscreen Keyboard
When a keyboard is not used it is still possible to bring up the onscreen keyboard.
1. Press and hold anywhere on the screen until the “x” appear at the top of the screen. Click on the “x”.
1.1. On the taskbar at the bottom of the screen, click on the icon that looks like a keyboard
1.2. Click on the icon in the top right of the keyboard to undock it. Now the
keyboard can be moved around the screen
1.3. Click in the bottom right of keyboard on the icon 123 to get the number
pad to appear
1.4. Click the “x” in the top right-hand corner of the keyboard to close it out
1.5. Once keyboard use is complete, click on the screen.
1.6. Click the three dots in the top left corner of the web browser
1.7. Click the square next to the zoom buttons to bring the monitor back into
Fullscreen mode.
Modifying Layouts
Log in as an administrator
2. To login as admin click in the top right corner of the screen, click the door with an arrow point right to sign out.
Connect keyboard to the tablet or access the on-screen keyboard as described in previous section.
2.1. Login in with the following credentials (case sensitive, and don’t
forget exclamation at end)
2.1.1. Username: admin
2.1.2. Password: 123123123!
2.2. To login as guest/operator mode use the following credentials
(case sensitive)
2.2.1. Username: idi
2.2.2. Password: Password55
3. In general, always remember to Click apply and save, otherwise work will be lost.
3.1. There are 8 possible user set layouts that can be adjust the size, and location of windows (User0,1,2,3,4)
3.1.1. Start in Design mode (at the top of the page, 3rd tab, icon is 4 squares)
Installation Guide ilex
L280-0974 REV C www.imagediagnostics.com Page 6
3.1.2. On the right side of the screen select the desired user in the drop-
down menu. Click on the new layout tab, then select one of the
predefined layouts with the correct number of channels required
for layout. Avoid looking at the live screen at this point as the
images will be scaled incorrectly, this will be autocorrected in
the next few steps
3.1.3. Click save at the top
3.1.3.1. Note: Failure to click save will result in lost work
3.1.4. Re-arrange the windows using the following steps.
3.1.4.1. Click save, click in the desired window A, B, C, or D
3.1.4.2. Click and hold any corner of the desired window to change window size. Note: if the window
size becomes larger than the screen it will revert to its original size.
3.1.4.3. Click and hold in the center of a window to drag location around the screen. Note: dragging a
window past the edge of the screen is not allowed and will return to its original location. In
most cases, change the size of the window to be smaller prior to moving the window around
the screen, then enlarge if needed.
3.1.4.4. Sizing and moving can also be done via numerical
data at the bottom of the page. See Coordinate
information. X & Y are the coordinate points
relating to the overall location of window in the
monitor. W and H are the width and height of the
desired window. Enter the height and width of the
window first, then adjust location. Values that are
invalid will revert to original state. If there is not
data in a given row, that signifies that window is not
active in the given layout.
3rd
1st
Installation Guide ilex
L280-0974 REV C www.imagediagnostics.com Page 7
3.1.4.5. In the edit tab, set the layer requirements as needed
by clicking on the green box and selecting a layer
in the drop-down menu. L4 is considered the top
layer, L1 is bottom most layer.
3.1.4.6. To add a channel to a given layout click on the
letter in the edit tab and select turn on or off.
3.1.4.7. Click apply and save
3.1.5. Cropping may be required to make the image fill the
entire window. Since aspect ratio is turned on, the image may
not be correctly cropped/and or scaled. Cropping adjustments will be
made in the next few steps, after the channels have been designated to
the appropriate window locations.
3.1.6. Layout has been configured and now the channels can be assigned to window locations and channels
can also be cropped at this time.
3.1.7. Before changing tabs click apply and save, failure to do so will result in lost work.
Assigning Channels to Window Location
4. Each channel input 1,2,3,4 can be
assigned to a window, A, B, C, or
D. Channels can also be duplicated
on to different windows
4.1. Go to preset and channel mode
(2nd tab looks like slider
buttons)
4.2. Select QUAD, from the dropdown
menu
4.3. Change A to reference Channel 1,
B>CH2, C>CH3,D>Ch4
4.4. Click a different channel in row A,
notice the screen changes.
4.5. Assign channels to the appropriate window as needed.
Installation Guide ilex
L280-0974 REV C www.imagediagnostics.com Page 8
Cropping Windows
5. Steps used to crop windows and channels
5.1. Go to Preset and channel mode (2nd tab,
pencil icon)
5.2. Locate the drop-down menu called preset and
channel
5.3. Drop down and select CH1
5.4. Click on the input cropping slider to activate
cropping
5.5. Enter the desired values:
5.5.1. X1 = crop left side of image
5.5.2. Y1 = crop top of image
5.5.3. X2 = crop right side of image
5.5.4. Y2 = crop right side of image
Example:
Otros manuales para ilex
2
Tabla de contenidos
Otros manuales de Equipo médico de idi
idi
idi Ilex 55 Manual de usuario
idi
idi Aspect 100-4T G3 Manual de usuario
idi
idi Aspect100E Manual de usuario
idi
idi Aspect Iso-Drive Q-CARD Manual de usuario
idi
idi Aspect ISR G3 Manual de usuario
idi
idi Ilex Q-Card Manual de usuario
idi
idi Aspect100US Manual de usuario
idi
idi MDS Guía del administrador
idi
idi ilex Manual de usuario
idi
idi Aspect Q-CARD 100-4T Manual de usuario
idi
idi Aspect ISO-Drive Manual de usuario
idi
idi Aspect100-4 Manual de usuario
idi
idi Aspect 100RTL Q-CARD Manual de usuario
idi
idi Aspect100UC Plus Manual de usuario
idi
idi Aspect ISR G3 Manual de usuario
idi
idi Aspect100T Manual de usuario
idi
idi Aspect 100-4T G3 Manual de usuario
idi
idi Aspect 100-4 Q-CARD Manual de usuario
idi
idi Ilex 55 Manual de usuario
idi
idi Aspect 100-4 Q-CARD Manual de usuario
