idi ilex Manual de usuario
Mobile Video Integration System
The text of this manual was originally written, approved and published by the manufacturer in English.
The information and images in this document are proprietary to IDI and is only for use for and by IDI
representatives or their Agents.
L280-0693 REV A Image Diagnostics Inc. Company Confidential 1
Installation Guide
For units using IPS500A video signal router
Clinical set Up
Input locations 1&3 are
paired in the PIP side-by-
side mode. Image 3 can
have multiple active
image sources that can
be changed via the
IPS500 Input button
1 2
4
3
Image Location 1Image Location 2
Source Destination Location is set by the numbers printed on the Video Panel. The #3 on the
panel connects images to the #3 location on the Monitor and can be changed via the
IPS500A controller.
Input Source
Monitor
Location
IPS500A Flex Location 3
Each IPS500A can route up to (2) DVI, (1) VGA,
(1) SOG, (1) S-Video and (1) SDI input
2
Image Location 4
Flex Image Location 3
Left Right
Source Inputs
3
2
Changes Input 3
Monitor Screen
L280-0693 REV A Image Diagnostics Inc. Company Confidential
Component Configuration
Input manual selector IPS500A
•IPS500A –Primary routing device and switcher for position #3
General
•Inputs routed through the IPS500A can be manually changed by selecting the Input button and toggle
through the various inputs.
•Output setting must be set to 1080P at 60 HZ.
FSN IPS500A (Front and Rear)
Select Key
(enters selection)
Output Selection
(shown) always 1080P -60)
Input Switching (shown)
SOG Input
Inputs
DVI I
DVI D
Output ON/OFF
Front
Rear
SDI Input
IPS500A Menu Settings
•On/OFF button in rear and front have to be on (screen will illuminate green)
Factory Preset Menu Settings
•Auto Search for Input set to off
•PIP Layout set to no
•Fill Aspect
•Always 1080p60 Output Setting
3
S-Video Input
VGA input
L280-0693 REV A Image Diagnostics Inc. Company Confidential
Examples for: C Arms, Cameras, Hemodynamics, PACS or Ultrasound
•The Green on/off button turns the system on. If the monitor doesn’t boot
up then press the Master Power switch located in the Monitors rear input
manifold right next to the power cable insertion point
•The source cable’s insertion location on the rear input plate determines
the image’s location on the Monitor
•Inputs 1 & 3 are paired in PIP mode and recycled back to the single mode
via the hand switch PIP button or Monitor’s Side Control panel
•Single images can be independently managed through the hand switch
SOURCE button (or monitor Menu).
•The ilex is configured/converted for DVI monitor Inputs only. Images will
not present if DP or SDI monitor inputs are selected. Toggle through the
SOURCE inputs until you see DVI in the lower right corner of monitor
•Multiple images in the #3 position can be manually changed via the
IPS500A.
Configuration
Source:
Changes the Single
Primary Source
Image and input
source mode.
PIP:
Changes the PIP
format from
Single, PIP, PBP,
Triple, Quad
view and back to
single mode
Hand Control
Single
PBP
Quad
34
2
1
Up/Down
on/off
Emergency Stop
Video Convertor
Array
Brakes
4
IPS500A Switcher
Speaker Control
PIP cycle
Flex Position
Triple
PIP
L280-0693 REV A Image Diagnostics Inc. Company Confidential
Image Local and Programing
or
or
or
1
2
3
4
1. Selects the single image
displayed and selects
Monitors input
configuration
2.The system is
configured for DVI.
Images will not display
if DP, or SDI mode
signals are selected
(lower right corner pop
up window
3. When in a PIP mode,
swaps image pair from
1&3 to 2&4.
Selects the
monitors PIP
modes - single,
PIP, PBP, Triple or
quad view and
back again
Sources
Single
5
3 position is flexible and inputs
selected via the IPS500A
To change Source
1. Press Source verify, green box is around correct
window,. Press Source again to go to next window
2. Press down to get to desired input
3. Press “+“
L280-0693 REV A Image Diagnostics Inc. Company Confidential
From FSN out of box IDI, all configurations
6
Mode Select
From FSN manual
Each of the PBP, Triple
and Quad have available
modes to modify the
layout
To change mode
1. Press Menu
2. Press down to get
to PIP(4th) icon
3. Press “+“
4. Press Down to
select mode
5. Press “+” to
change mode
L280-0693 REV A Image Diagnostics Inc. Company Confidential
Ilex System ON/OFF resetting the stands breaker. Note: the
monitor has its own Master on/off switch (near power cord)
that may need to to set to on.
The front toggle switch activates the column UP/Down.
Note: use this button to compress the shipping foam
Pressing the red emergency stop in does not allow
elevation. Push this button in when relocating (shipping
and intra-room) the ilex to ensure that the monitor will not
change elevation. Reset by rotating the button a quarter
turn.
The speaker system on the ilex can be direct connected
(wire into the mic. connector) or wireless through the BT
connection. Turn the power knob on and set the input
select switch to (BT).
When using the wireless option, look for the “BT-RY” pairing
device on your source system. If it doesn’t appear
automatically, press and hold the volume button for three
seconds. Once connected, adjust the volume to your desired
level.
Other ilex Feature Programing
The ilex is equipped with a castor motion locking system for
transport and clinical operation.
Free Float –The middle position of the castor locking pedal
(horizontal to floor) allows for movement of the ilex in any
horizontal direction.
Total Lock – Step down on the pedal’s red pad to lock all
horizontal movement of the ilex. Step down on the pedal’s
green pad to return to the Free Float position.
Steer Lock – Step down on the pedal’s green pad to lock the
steering direction of the 2 casters on the opposite side of the
pedal. Step down on the pedal’s red pad to return to the
Free Float position.
7
Speaker covers are magnetic and can be easily removed for
cleaning
L280-0693 REV A Image Diagnostics Inc. Company Confidential
Menu Access Points
•Lower Right Side
•Remote Control
Monitor Menu Navigation
8
From FSN Manual FSN1995 –10/2019
L280-0693 REV A Image Diagnostics Inc. Company Confidential
Monitor Set-up
FSN 55” 4K Monitor
9
From FSN Manual FSN1995 –10/2019
L280-0693 REV A Image Diagnostics Inc. Company Confidential
Monitor Menu Adjustments
10L280-0693 REV A Image Diagnostics Inc. Company Confidential
Otros manuales para ilex
2
Tabla de contenidos
Otros manuales de Equipo médico de idi
idi
idi Ilex Q-Card Manual de usuario
idi
idi Aspect 100-4 Q-CARD Manual de usuario
idi
idi ilex Manual de usuario
idi
idi Aspect 100UC Plus Q-CARD Manual de usuario
idi
idi 1000F Series Manual del producto
idi
idi Aspect ISR G3 Manual de usuario
idi
idi MDS Guía del administrador
idi
idi Aspect100E Manual de usuario
idi
idi Aspect 100-4T G3 Manual de usuario
idi
idi Ilex 55 Manual de usuario
idi
idi Aspect Q-CARD 100-4T Manual de usuario
idi
idi Aspect 100-4T G3 Manual de usuario
idi
idi Aspect ISO-Drive Manual de usuario
idi
idi Aspect Iso-Drive Q-CARD Manual de usuario
idi
idi Aspect100UC Plus Manual de usuario
idi
idi Aspect 100-4 Q-CARD Manual de usuario
idi
idi Aspect100US Manual de usuario
idi
idi Aspect 100-4 Q-CARD Manual de usuario
idi
idi Aspect ISR G3 Manual de usuario
idi
idi Aspect100-4 Manual de usuario
