6
SA1E Miniature Photoelectric Switches (Built-in Amplifier)
Slits (for through-beam)
Item Slit Size Part No. Ordering No.
Package
Quantity
Vertical Slit
0.5 mm × 18 mm SA9Z-S06 SA9Z-S06PN02
2
1.0 mm × 18 mm SA9Z-S07 SA9Z-S07PN02
2.0 mm × 18 mm SA9Z-S08 SA9Z-S08PN02
Horizontal
Slit
0.5 mm × 6.5 mm SA9Z-S09 SA9Z-S09PN02
1.0 mm × 6.5 mm SA9Z-S10 SA9Z-S10PN02
2.0 mm × 6.5 mm SA9Z-S11 SA9Z-S11PN02
Round Slit
ø0.5 mm SA9Z-S12 SA9Z-S12PN02
ø1.0 mm SA9Z-S13 SA9Z-S13PN02
ø2.0 mm SA9Z-S14 SA9Z-S14PN02
Reflectors (for polarized retro-reflective)
Item Part No. Package
Quantity
Reflector
Standard IAC-R5
1
Small IAC-R6
Large IAC-R8
Narrow (rear/side mounting) IAC-R7M
Narrow (rear mounting) IAC-R7B
Narrow (side mounting) IAC-R7S
Tape Type (40 × 35 mm) IAC-RS1
Tape Type (80 × 70 mm) IAC-RS2
Reflector
Mounting
Bracket
For IAC-R5 IAC-L2
For IAC-R6 IAC-L3
For IAC-R8 IAC-L5
•See page R-12 for dimensions.
•The IAC-L2 is not supplied with mounting screws and nuts. Use
commercially available M4 screws and nuts for mounting the IAC-R5
reflector.
•The IAC-L3 is supplied with two mounting screws (M3 × 8 mm sems screws).
•The IAC-L5 is supplied with two mounting screws (M4 × 10 mm sems
screws).
•The IAC-R7M and IAC-R7S are supplied with two M3 × 8 mm self-tapping
screws, two flat washers, and two spring washers.
•The IAC-R7B is supplied with an M3 × 8 mm self-tapping screw, a flat
washer, and a spring washer.
Sensor Mounting Brackets
Item Part No. Package
Quantity
Main Unit
Mounting Brackets
Vertical Mounting SA9Z-K01
1
Horizontal Mounting SA9Z-K02
Cover type SA9Z-K03
Back Mounting SA9Z-K04
•Two mounting screws (M3 × 12 mm sems screws) are supplied with the
SA9Z-K01 and SA9Z-K02.
•Two mounting screws (M3 × 14 mm sems screws) are supplied with the
SA9Z-K03.
•The through-beam model requires two mounting brackets, one each for the
projector and the receiver.
•The SA9Z-K02 cannot be used for the connector models.
•Contact IDEC about mounting brackets for the connector.
Connector Cable (for M8 connector model)
Number of
Core Wires Style & Length Part No. Package
Quantity
4
Straight, 2m SA9Z-CM8K-4S2
1
Right angle, 2m SA9Z-CM8K-4L2
Straight, 5m SA9Z-CM8K-4S5
Right angle, 5m SA9Z-CM8K-4L5
Reflectors (used only for coaxial polarized retro-reflective)
Item Part No. Package
Quantity
Reflector
Standard IAC-R9
1
Small IAC-R10
Ultra-small IAC-R11
Reflector Mounting Bracket For IAC-R9 IAC-L3
Air Blower Mounting Block
Item Part No. Package Quantity
Air Blower Mounting Block SA9Z–A02 1
•Two mounting screws (M3 × 20 mm sems screws), one M5 × 6 mm screw
for plugging the air supply port, and one gasket (0.5 mm thick) are supplied.
•The air tube fitting and mounting bracket are not supplied and must be
ordered separately (recommended mounting bracket: SA9Z-K01).
•Material: Anodized aluminum surface
Sensitivity Control Screwdriver
Item Part No. Package Quantity
Sensitivity Control Screwdriver
SA9Z-AD01 1
Accessories (optional)
