175
800-262-IDEC (4332) •USA & Canada
SA1E
Sensors
OI Touchscreens PLCs Automation Software Power Supplies Sensors Communication Barriers
Specifications, con’t
Sensing Method Through-beam Polarized
Retroreflective Diffuse-reflective Small-beam
Reflective
Background
Suppression (BGS)
Convergent
Reflective Transparent
Part No. SA1E-T SA1E-P SA1E-D SA1E-N SA1E-B SA1E-G SA1E-X
Operating Temperature –25 to +55°C (no freezing)
Operating Humidity 35 to 85% RH (no condensation)
Storage Temperature –40 to +70°C (no freezing)
Insulation Resistance Between live part and mounting bracket: 20 MΩ maximum (500V DC megger)
Dielectric Strength Between live part and mounting bracket: 1000V AC, 50/60 Hz, 1 minute
Vibration Resistance Damage limits: 10 to 55 Hz, Amplitude 0.75 mm, 20 cycles in each of 3 axes
Shock Resistance Damage limits: 500 m/s2, 10 shocks in each of 3 axes
Material Housing: PC/PBT, Lens: PC (Polarized retroreflective / coaxial polarized retro-reflective: PMMA), Indicator cover: PC
Attachments Instruction sheet
Weight
(approx.)
Cable
Model
Projector: 30g
Laser Projector: 35g
Receiver: 30g
2
Laser Receiver: 35g
30g 2
with laser: 35g 35g 330g 235g 3
Connector
Model
Projector: 10g
Laser Projector: 20g
Receiver: 10g
Laser Receiver: 20g
10g
with Laser 20g 20g 10g 20g
Connection
Method
Cable
Model ø3.5 mm, 3-core, 0.2 mm2, 1-m vinyl cabtyre cable (2-core for the projector of through-beam type)
Connector
Model M8 connector (4-pin)
1. Maintain at least the distance shown below between the SA1E photoelectric switch and reflector.
IAC-R5/R6/R7/R8: 100 mm
IAC-RS1/RS2: 150 mm
The detection distance cannot be guaranteed if the reflector is deformed or the tape type reflector is applied on uneven surface.
2. Cable length: 1m (50g when the cable length is 2m, 55g for laser models. 110g when the cable length is 5m, 120g for laser models.)
3. Cable length: 1m (55g when the cable length is 2m. 120g when the cable length is 5m.)
4. For laser models insert L in place of .
Slit and Sensing Range
A slit, which changes the beam size of through-beam sensors, can easily be attached to the sensing side of the through-beam
projector and receiver. Three different slit widths are available.
Slit
w/Sensitivity Adjustment w/o Sensitivity Adjustment
Sensing Range (m) Minimum Detectable
Object Width (mm) Sensing Range (m) Minimum Detectable
Object Width (mm)
Part No. Slit Width: A Used on
one side
Used on
both sides
Used on
one side
Used on
both sides
Used on
one side
Used on
both sides
Used on
one side
Used on
both sides
SA9Z-S06 0.5 mm 2.5 1.0 7.0 0.5 5.0 1.5 7.0 0.5
SA9Z-S07 1.0 mm 3.5 1.5 7.0 1.0 7.0 3.0 7.0 1.0
SA9Z-S08 2.0 mm 6.0 3.5 7.0 2.0 9.0 5.5 7.0 2.0
SA9Z-S09 0.5 mm 2.0 0.7 7.0 0.4 4.0 1.5 7.0 0.5
SA9Z-S10 1.0 mm 3.0 1.5 7.0 0.7 7.0 2.5 7.0 0.8
SA9Z-S11 2.0 mm 5.5 3.0 7.0 1.5 9.0 5.0 7.0 1.5
SA9Z-S12 0.5 mm 0.8 0.08 5.0 0.3 1.3 0.1 5.0 0.5
SA9Z-S13 1.0 mm 1.5 0.3 5.0 0.6 2.5 0.3 5.0 0.6
SA9Z-S14 2.0 mm 2.5 1.2 5.0 1.5 5.5 1.6 5.0 1.7
Used on one side: Slit is attached to the receiver only.
Slit
(stainless steel)
The slit can be pressed to
snap onto the front easily.
Horizontal slits and round slits have
an orientation. Make sure that the
TOP marking comes on top of the
sensor (LED side).
