Icron 00-00437 Manual de usuario

Icron USB 3-2-1 Raven

™3124

4-Port USB 3.1, 200m Multimode Fiber

Point-to-Point Extender System

User Guide

Thank you for purchasing the USB 3-2-1 Raven™ 3124.

Please read this guide thoroughly.

This document applies to the following part numbers:

Model

North

American

System

European

System

United

Kingdom

System

Australia

System

Japan

System

Icron USB 3-2-1 Raven 3124 00-00437 00-00438 00-00439 00-00440 00-00441

FCC Radio Frequency Interference Statement Warning

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received

including interference that may cause undesired operation.

CE Statement

We, Icron Technologies Corporation, declare under our sole responsibility that the USB 3-2-1 Raven™ 3124, to

which this declaration relates, is in conformity with European Standards EN 55022, EN 55024, EN 55032 and

EN 61000.

IC Statement

This Class B digital apparatus complies with Canadian ICES-003 Issue 6.

WEEE Statement

The European Union has established regulations for the collection and recycling of all waste electrical

and electronic equipment (WEEE). Implementation of WEEE regulations may vary slightly by individual EU

member states. Please check with your local and state government guidelines for safe disposal and recycling

or contact your national WEEE recycling agency for more information.

Product Operation and Storage

Please read and follow all instructions provided with this product, and operate for intended use only.

Do not attempt to open the product casing as this may cause damage and will void warranty. Use only the

power supply provided with this product (if applicable). When not in use, product should be stored in a dry

location between -20°C and 70°C.

Document #90-01579-A01

Contents

Introduction.............................................................................................................3

Product Contents ................................................................................................................................ 3

Features .................................................................................................................................................. 3

The LEX Unit.......................................................................................................................................... 4

The REX Unit.......................................................................................................................................... 5

Installation Guide....................................................................................................6

Installing the USB 3-2-1 Raven 3124 System............................................................................. 6

Fiber Optic Cabling............................................................................................................................. 6

Requirements ....................................................................................................................................... 6

Preparing Your Site ............................................................................................................................. 6

Installing the LEX Unit ...................................................................................................................... 7

Connecting the LEX to the REX ..................................................................................................... 7

Installing the REX Unit....................................................................................................................... 7

Checking the Installation ................................................................................................................. 7

Connecting a USB Device................................................................................................................. 8

Compatibility ........................................................................................................................................ 8

Optional Ethernet Pass Through Connection ........................................................................... 8

Optional USB Extender Mounting Options ...........................................................9

Troubleshooting ....................................................................................................11

Warranty Information ...........................................................................................14

Obtaining Warranty Service .................................................................................14

Specifications.........................................................................................................15

Contacting Technical Support ..............................................................................16

Technical Glossary.................................................................................................17

Introduction

This guide provides product information for the USB 3-2-1 Raven™ 3124, installation instructions and

troubleshooting guidelines. The instructions in this guide assume a general knowledge of computer

installation procedures, familiarity with cabling requirements and some understanding of USB devices.

NOTE: Notes provide additional information that could be useful.

CAUTION: Cautions provide important information about an operational requirement.

Product Contents

Your Raven 3124 extender system contains:

• LEX (Local Extender)

• REX (Remote Extender)

• USB 3.1 Gen 1 Cable

• LEX 24V DC 1A International Power Adapter

• REX 24V DC 2.71A International Power Adapter

• 2 x Country Specic Power Cables

• Quick Start Guide

Features

The Raven 3124 incorporates ExtremeUSB-C™ technology, enabling users to extend USB 3.1 beyond the

standard 3m cable limit for USB 3.1 peripheral devices. This extender system is composed of two individual

units, the LEX and the REX, and has the following key features:

• Up to 200m of extension when directly connected over OM3 multimode ber

• Support for new USB 3.1 Gen 1/2 host controllers and devices (up to 5 Gbps)

• Support for all device USB types

• Backwards compatible to USB 2.0 devices

The Raven 3124 only works with OM3 multimode ber or higher grade.

note

The Raven 3124 includes the ExtremeUSB-C™ suite of features:

• Transparent USB extension supporting USB 3, 2 and 1

• True plug and play; no software drivers required

• Works with all major operating systems: Windows®, macOS™, Linux® and Chrome OS™

The LEX Unit

The LEX unit connects to the computer using a standard USB 3.1 Gen 1 cable. Power for this unit is provided by the

included 24V 1A adapter.

ITEM TYPE DESCRIPTION

1 Power LED LED is SOLID ON when DC is supplied to the extender unit. LED is OFF when no

power is supplied by the AC Adapter

2 Mode Reserved for manufacturer use.

3 Config Reserved for manufacturer use.

4 Status LED LED is SOLID ON when system is functioning normally. LED BLINKS when system is

booting OR to indicate a temperature warning in unison with the LINK, USB 2, and

USB 3 LEDs.

5 Link LED LED is SOLID ON when LEX is linked to an opposite REX. LED is OFF when there is

no connection between the LEX and REX units.

6 USB 2 LED LED is SOLID ON when an active USB 2 connection is established through the

extender system. LED BLINKS when the USB 2 connection is suspended/asleep.

LED is OFF when no USB 2 connection is detected.

7 USB 3 LED LED is SOLID ON when an active USB 3 connection is established through the

extender system. LED BLINKS when the USB 3 connection is suspended/asleep.

LED is OFF when no USB 3 connection is detected.

8 LAN Port (100 Mbps) Ethernet pass through channel connects to a network or Ethernet device.

9 Link Port Extension link Duplex LC ber optic transceiver port.

10 USB Host Port USB 3 Type B receptacle used to connect LEX to USB 3 Host computer.

11 DC Power Port Locking connector for the included power adapter – accepts 24VDC 1A.

Front View

Rear View

Config

USB2 USB3ModePower LinkStatus

1245 6 7

LAN 24V 1AUSB

Link

8910 11

The REX Unit

The REX unit provides USB 3.1 Type A ports for standard USB devices and allows you to connect up to four USB devices

directly. Additional devices may be connected by attaching up to three USB hubs to the REX. The REX is powered by

an external AC 24V 2.71A adapter, supplying up to 1.2 Amp per USB port.

ITEM TYPE DESCRIPTION

1 Power LED LED is SOLID ON when DC is supplied to the extender unit. LED is OFF when no

power is supplied by the AC Adapter.

2 Mode Reserved for manufacturer use.

3 Config Reserved for manufacturer use.

4 Status LED LED is SOLID ON when system is functioning normally. LED BLINKS when system

is booting OR to indicate a temperature warning in unison with the LINK, USB 2,

and USB 3 LEDs.

5 Link LED LED is SOLID ON when LEX is linked to an opposite REX. LED is OFF when there is

no connection between the LEX and REX units.

6 USB 2 LED LED is SOLID ON when an active USB 2 connection is established through the

extender system. LED BLINKS when the USB 2 connection is suspended/asleep.

LED is OFF when no USB 2 connection is detected.

7 USB 3 LED LED is SOLID ON when an active USB 3 connection is established through the

extender system. LED BLINKS when the USB 3 connection is suspended/asleep.

LED is OFF when no USB 3 connection is detected.

8 LAN Port (100 Mbps) Ethernet pass through channel connects to a network or Ethernet device.

9 Link Port Extension link Duplex LC ber optic transceiver port.

10 Device Ports (Type A) Accepts all USB devices.

11 DC Power Port Locking connector for the included power adapter – accepts 24VDC 2.71A.

Front View

Rear View

Config

USB2 USB3ModePower LinkStatus

1245 6 7

LAN USBUSB USB USB

Link

24V 2.71A

10 10

Installation Guide

Installing the USB 3-2-1 Raven 3124 System

Requirements

To complete the installation, you will also require the following items that are not included with this system:

• USB compatible computer (host computer) with a USB compliant operating system

• USB compatible device(s)

• OM3 Fiber optic cabling

Fiber Optic Link Cabling

The LEX and REX extenders are interconnected by fiber optic cabling. Duplex multimode ber cabling

is required for the Raven 3124 for extending up to 200m using 50/125μm OM3 grade cable. The cabling

subsystem must provide a duplex connection with crossover, and must be terminated with Duplex LC

connectors at both ends.

Preparing Your Site

Before installing the Raven 3124 extender, you will need to prepare your site:

1. Place the computer where desired and set it up.

2. Ensure to locate the USB device(s) within the cable-length of the computer. If not, adjust the

location of the device(s) and/or computer accordingly.

3. If you are using surface cabling, the Raven 3124 supports a maximum distance of 200m over OM3

multimode ber.

4. If using premise cabling, ensure compatible ber optic cabling is installed between the two locations

and does not to exceed the specied distance.

Host USB Devices

LEX REX

USB 3-2-1

up to 200m over MMF

LAN IP Control

OM3 Fiber Optic Link Cable

USB Cable

Optional Network Connections

Installing the LEX Unit

1. Place the LEX unit near the computer.

2. Assemble the power adapter and country specic power cord together and connect them into a

suitable AC outlet.

3. Connect the supplied USB 3.1 Gen cable between the LEX host port and a USB 3 port on the host

computer.

Connecting the LEX to the REX

With Surface Cabling:

1. Plug one end of the ber optic cabling (not included) into the Link port on the LEX.

2. Plug the other end of the ber optic cabling into the Link port on the REX.

With Premise Cabling:

1. Plug one end of a ber optic patch cord (not included) into the Link port on the LEX.

2. Plug the other end of the patch cord into the ber optic information outlet near the host computer.

3. Plug one end of the second ber optic patch cord (not included) into the Link port on the REX.

4. Plug the other end of the second patch cord into the ber optic information outlet near the USB

device.

Installing the REX Unit

1. Place the REX near the USB device(s).

2. Connect the power adapter to the REX.

Checking the Installation

1. On the LEX and REX units, check that the Power, Status, Link, USB 2 and USB 3 LEDs are on. If

the Link LEDs are permanently o, then the cabling between the LEX and REX units may not be

installed properly or is defective.

2. For Windows users (XP, 7, 8, 8.1, 10), open Device Manager to conrm that the extender system has

been installed correctly. Expand the entry for Universal Serial Bus controllers by clicking the “+” sign.

If the extender system has been installed correctly, you should find two separate instances of

“Generic SuperSpeed USB Hub” listed.

To open Device Manager in Windows XP:

Right click “My Computer” then select: Properties >> Hardware tab >> Device Manager

To open Device Manager in Windows 7:

Open the Start Menu, right click on“Computer”then select: Manage >> Device Manager

To open Device Manager in Windows 8, 8.1 or 10:

Right click the Start Menu and then select: Device Manager

note

3. For macOS users, open the System Profiler to conrm that the extender system has installed correctly.

In the left-hand column under Hardware, select “USB” and inspect the right hand panel. If the

extender has been installed correctly, you should find it listed as two separate instances of“Hub”

under the USB SuperSpeed Bus.

To open System Profiler in macOS:

Open the Finder, select Applications, then open the Utilities folder and double click on the System Proler icon.

4. If the extender system is not detected correctly or fails to detect, please consult the Troubleshooting

section in this guide.

Connecting a USB Device

1. Install any software required to operate the USB device. Refer to the documentation for the USB

device, as required.

2. Connect the USB device to the device port on the REX.

3. Check that the device is detected and installed properly in the operating system.

Compatibility

The USB 3-2-1 Raven 3124 complies with USB 2.0 and USB 3.1 Gen 1 specications governing the design of

USB devices. However, there is no guarantee that all USB devices or hosts will be compatible as there are a

number of dierent characteristics that may impact the operation of USB devices over extended distances.

Optional Ethernet Pass Through Connection

The Raven 3124 oers a 100 Mbps Ethernet pass through connection that can be used for a variety of

purposes including:

• Connecting network devices

• Providing remote network access to the same location as the REX unit

• Leveraging existing cabling to provide USB 3-2-1 connectivity without losing network connectivity

Connect any network device or access port into the RJ45 socket label “LAN” using up to 100 meters of

standard CAT 5e, 6 or 7 cabling.

note

LEX REX

Up to 200m

over OM3 MMF

LAN Network

Device

Up to 100m

CAT 5e/6/7

Up to 100m

CAT 5e/6/7

Optional USB Extender Mounting Options

The bottom of the enclosure features four convenient pre-drilled holes for optional mounting. Based on

your requirements, choose from two available mounting options:

1. USB Extender Mounting Kit (Purchased separately Order Part #10-00620 USB Mounting Kit - Silver)

2. USB Extender Direct Surface Mounting (Using your own hardware, stencil provided on page 10)

OPTION 1: USB Extender Mounting Kit - each kit includes:

• 2 mounting brackets

• 4 (M3) locking washers

• 4 (M3 x 10mm) Phillips screws

• Mounting bracket installation guide (see diagram below)

1 kit required to mount per LEX or REX

Using a Phillips screwdriver, in the order as illustrated below, fasten and secure the provided screws, locking

washers and brackets into place.

Once the bracket mounting is secured onto the extender, it is ready for mounting onto a surface. Please note

you will need to provide your own screws to secure the extender using the available slots on each bracket.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Extensor de Icron

Icron

Icron USB 2.0 Ranger 2304GE-LAN Manual de usuario

Icron

Icron USB-2000 Manual de usuario

Icron

Icron EL3500 Manual de usuario

Icron

Icron USB 2.0 Ranger 442 Manual de usuario

Icron

Icron EL4500 Manual de usuario

Icron

Icron USB 2.0 Ranger 2304-LAN Manual de usuario

Icron

Icron EL5200 HDMI + USB 2.0 Extender Manual de usuario

Icron

Icron RG2304-LAN Manual de usuario

Icron

Icron Raven 3204C Manual de usuario

Icron

Icron USB 3-2-1 Starling 3251C Manual de usuario

Icron

Icron VU5100 Manual de usuario

Icron

Icron USB 3.0 SP3022 Manual de usuario

Icron

Icron USB Ranger 2201 Manual de usuario

Icron

Icron USB 3-2-1 Raven 3104 Manual de usuario

Icron

Icron USB 2.0 RG2211 Manual de usuario

Icron

Icron USB Ranger 2212 Manual de usuario

Icron

Icron USB 2.0 RG2304GE-LAN Manual de usuario

Icron

Icron EL5100 Manual de usuario

Icron

Icron USB 2.0 RG2301 Manual de usuario

Icron

Icron USB 2.0 Ranger 2311 Manual de usuario

Icron

Icron USB Ranger 2211 Manual de usuario

Icron

Icron RG2301 Manual de usuario

Icron

Icron USB Ranger 2204 Manual de usuario

Icron

Icron EL5353 Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario