ICP DAS USA I-7018 Manual de usuario

I-7018(R)(BL)(P), M-7018(R) Quick Start Guide

Warranty

All products manufactured by ICP DAS are under warranty regarding defective materials for a period of one year from the date

of delivery to the original purchaser.

Warning

ICP DAS assumes no liability for damages resulting from the use of this product. ICP DAS reserves the right to change this

manual at any time without notification. The information furnished by ICP DAS is believed to be accurate and reliable.

However, no responsibility is assumed by ICP DAS for its use, or for any infringements of patents or other rights of third

parties resulting from its use.

Packing List

I-7018(R)(BL)(P) or M-7018(R)

Plastic Rail

Quick Start Guide

Internal I/O Structure < I-7018(BL)(P), M-7018 >

Pin Assignments < I-7018(BL)(P) >

Pin Assignments

< I-7018R, M-7018, M-7018R >

Internal I/O Structure < I-7018R, M-7018R >

Wire Connections < I-7018(BL)(P) Channel 0 –5, M-7018 , I-7018R, M-7018R >

Page 1

Wire Connections < I-7018(BL)(P) Channel 6 –7 >

Modbus Table (M-7018, M-7018R only)

Address

Description

R/W

30001 ~

30008

40001 ~

40008

Analog input value of channel 0 to 7

30129

40129

CJC temperature in 0.01°C

40353 ~

40360

CJC offset of channel 0 to 7 in 0.1°C.

1 for 0.1, 127 for 12.7, 255 for –0.1,

128 for –12.8

R/W

40481

Firmware version (low word)

40482

Firmware version (high word)

40483

Module name (low word)

40484

Module name (high word)

40485

Module address, valid range: 1 ~ 247

R/W

40486

Bits 5:0

Baud rate, 0x03 ~ 0x0A

Code

0x03

0x04

0x05

0x06

Baud

1200

2400

4800

9600

Code

0x07

0x08

0x09

0x0A

Baud

19200

38400

57600

115200

Bits 7:6

00: no parity, 1 stop bit

01: no parity, 2 stop bit

10: even parity, 1 stop bit

11: odd parity, 1 stop bit

R/W

40487

Type code

R/W

Address

Description

R/W

40488

Modbus response delay time in ms,

valid range: 0 ~ 30

R/W

40489

Host watchdog timeout value, 0 ~

255, in 0.1s

R/W

40490

Channel enable/disable, 00h ~ FFh

R/W

40491

Module CJC offset in 0.01°C

R/W

40492

Host watchdog timeout count, write 0

to clear

R/W

00257

Protocol, 0: DCON, 1: Modbus RTU

R/W

00259

Filter setting, 0: 60Hz rejection, 1:

50Hz rejection

R/W

00260

Modbus host watchdog mode

0: same as I-7000

1: can use AO and DO command to

clear host watchdog timeout status

00261

1: enable, 0: disable host watchdog

R/W

00268

1: enable, 0: disable CJC

R/W

00269

Modbus data format, 0: hex, 1:

engineering

R/W

00270

Host watch dog timeout status, write

1 to clear host watch dog timeout

status

R/W

00273

Reset status, 1: first read after

powered on, 0: not the first read after

powered on

DCON Protocol

Functions

Command

Response

Notes

Read module name

$AAM

!AA(Data)

AA: address number

Read module firmware version

$AAF

!AA(Data)

Read all analog input data

#aa

>(data)

Read analog input data of each channel (<=16 channel)

#aai

>(data)

i: channel number (Hex)

Read analog input data of each channel (>16 channel)

#aaii

>(data)

ii: channel number (Hex)

Page 2

Module test and configuration

Step 1: INIT switch Operation

1. Find out the INIT switch( back of the module),

and turn to INIT.

2. Reboot the module

Step 2: Install & Run DCON Utility

1. Please Install DCON Utility first

You can find the software in the CD.

CD path:

<Driver>:\napdos\driver\dcon_utility\

Web link:

http://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_utility/

2. Run DCON utility

Step 3: Set search configuration & search module

Step 4: Select Module for testing and configuration

1. Click “COM Port”

2. Assign the communication information and click

“OK”

Module Default Setting

COM Port

Refer converter Port Number

Baud Rate

9600

Protocol

DCON for I-7000

Modbus RTU for M-7000

Parity Option

N,8,1

3. Click “Search” and select “Start Searching”

Software will search the modules from COM Port

4. Click “Search“ and select “stop searching”

Manual stop when the modules searched

Note:

When no module can be searched, please check the

wire and communication information

Select COM Port Number

Double click “select module”

Page 3

Step 5: Configuration Settings & Channel Settings

Module Settings

Protocol

DCON / Modbus

Address

1~255 (0:INIT)

Baud rate

1200~115200

Parity option

N,8,1

Input range

Depends on signal

sources

Step 6: Change to normal mode and keep the settings

1. Turn the INIT Switch to Normal.

2. Reboot the module

Trouble Shooting

Q1. How to do when forgot module address or baud rate?

Please turn to INIT mode, and run DCON Utility to search.

The module supports DCON protocol at the INIT mode.

And the address is 0. The communication setting is “9600,N,8,1”.

Q2. How to configure the I-7000 and M-7000 modules?

ICP DAS provide DCON Utility to configure I-7000 and M-7000 modules.

Please download the last version from: http://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_utility/

Q3. How to measure the current?

I-7018(R)(BL)(P) and M-7018(R) require optional external resistance (125Ω) for current measurement.

Please refer wired connections diagram.

And then select a suitable input range by DCON Utility.

Q4. What is the CJC function?

CJC (Cold-Junction Compensation) offset is for the temperature measurement.

You can set a CJC offset for all channels or different channel in DCON Utility,

Q5. How to programming with I-7000 or M-7000 by C#, VB, VC?

ICP DAS I-7000 and M-7000 series both support DCON protocol. And Only M-7000 series supports Modbus protocol.

For DCON protocol, please download SDK and Demo from:

http://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_dll_new/

For Modbus protocol, please refer this web link:

http://www.icpdas.com/products/PAC/i-8000/modbus.htm

Channel Status

CJC Offset

Temperature Offset Settings

Este manual sirve para los siguientes modelos

Otros manuales de Sistema de E/S de ICP DAS USA

ICP DAS USA

ICP DAS USA ET-7000 series Manual de usuario

ICP DAS USA

ICP DAS USA PROFI-8455 Guía de configuración

ICP DAS USA

ICP DAS USA PCI-P16POR16U Manual de usuario

ICP DAS USA

ICP DAS USA SG-3071-G Manual de usuario

ICP DAS USA

ICP DAS USA P8R8-DIO Manual de usuario

ICP DAS USA

ICP DAS USA CAN-2024C Manual de usuario

ICP DAS USA

ICP DAS USA SG-3016 Manual de usuario

ICP DAS USA

ICP DAS USA WF-2055 Manual de usuario

ICP DAS USA

ICP DAS USA PETL-7060 Manual de usuario

ICP DAS USA

ICP DAS USA HRT-711 Manual de usuario

ICP DAS USA

ICP DAS USA I-7018 CR Manual de usuario

ICP DAS USA

ICP DAS USA SG-3071 Manual de usuario

ICP DAS USA

ICP DAS USA I-7043D Manual de usuario

ICP DAS USA

ICP DAS USA PISO-P64 Series Manual de usuario

ICP DAS USA

ICP DAS USA CAN-2054C Manual de usuario

ICP DAS USA

ICP DAS USA PIO-DA4 Manual de usuario

ICP DAS USA

ICP DAS USA M-7011D Manual de usuario

ICP DAS USA

ICP DAS USA I-7060 Manual de usuario

ICP DAS USA

ICP DAS USA I-7061 Manual de usuario

ICP DAS USA

ICP DAS USA I-7021 Manual de usuario

ICP DAS USA

ICP DAS USA CAN-2018C Manual de usuario

ICP DAS USA

ICP DAS USA PCI-D64HU Manual de usuario

ICP DAS USA

ICP DAS USA PCI-D64HU Manual de usuario

ICP DAS USA

ICP DAS USA tET-PD6 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario