ICP DAS USA M-7011 Manual de usuario

M-7011 1-channel Thermocouple input DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

M-7011

1-channel Thermocouple Input Data

Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7011.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The M-7011 is a one-channel Thermocouple input module. It provides cost-

effective protection and conditioning for a wide range of valuable industrial

control signals and systems. We provide free DCON utility which can help

users configure and test M-7011 modules. Plenty of library functions and

demo programs are provided which allows users to develop programs

easily on Windows, Linux and DOS operating systems. Users can mount

the modules on a DIN rail, panel or wall. Modules have a screw-terminal

block to connect to the signals.

2. Terminal Assignment

M-7011 1-channel Thermocouple input DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

M-7011 1-channel Thermocouple input DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Default Settings

Default setting for M-7011/11D :

- Address : 01

- Analog Input Type : Type 05, -2.5 to +2.5 V

- Baudrate : 9600 bps

- Checksum disable, 60Hz rejection, engineer unit format

5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

M-7011 1-channel Thermocouple input DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

M-7011 1-channel Thermocouple input DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For M-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See Section 2.1 for

details. To configure the M-7005, the $AA7CiRrr command must also be sent. See user

manual Section 2.12 for details. For M-7000 modules using the Modbus RTU protocol,

configure the module using the following functions.

-Sub-function 04h of Function 46h, see user manual Section 3.6.2

-Sub-function 06h of Function 46h, see user manual Section 3.6.4

-Sub-function 08h of Function 46h, see user manual Section 3.6.6

Read data from the input channels: send either the #AA or #AAN commands to the

module. See user manual Sections 2.3 and 2.4 for details. For M-7000 modules using

the Modbus RTU protocol, use Function 04h to read the data from the input channels.

See user manual Section 3.3 for details.

M-7011 1-channel Thermocouple input DAQ Module - QuickStart (Oct/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Tabla de contenidos

Otros manuales de Sistema de E/S de ICP DAS USA

ICP DAS USA

ICP DAS USA ISO-P32S32W Manual de usuario

ICP DAS USA

ICP DAS USA IR-712-MTCP Manual de usuario

ICP DAS USA

ICP DAS USA RTU-140 Manual de usuario

ICP DAS USA

ICP DAS USA I-7065BD Manual de usuario

ICP DAS USA

ICP DAS USA CAN-2084C Manual de usuario

ICP DAS USA

ICP DAS USA I-7018 CR Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2050 Manual de usuario

ICP DAS USA

ICP DAS USA I-7061D Manual de usuario

ICP DAS USA

ICP DAS USA SG-3071 Manual de usuario

ICP DAS USA

ICP DAS USA SG-3071 Manual de usuario

ICP DAS USA

ICP DAS USA A-626 Manual de usuario

ICP DAS USA

ICP DAS USA EIP-2019 Manual de usuario

ICP DAS USA

ICP DAS USA M-7046 Manual de usuario

ICP DAS USA

ICP DAS USA PISO-P32C32U-5V Manual de usuario

ICP DAS USA

ICP DAS USA CAN-2088D Manual de usuario

ICP DAS USA

ICP DAS USA M-7053 Manual de usuario

ICP DAS USA

ICP DAS USA I-7019R Manual de usuario

ICP DAS USA

ICP DAS USA DGW-521 Manual de usuario

ICP DAS USA

ICP DAS USA DIO-96/144 Manual de usuario

ICP DAS USA

ICP DAS USA M-7084 Manual de usuario

ICP DAS USA

ICP DAS USA tGW-700 Series Manual de usuario

ICP DAS USA

ICP DAS USA A-826 Series Manual de usuario

ICP DAS USA

ICP DAS USA I-7043 Manual de usuario

ICP DAS USA

ICP DAS USA I-7019R Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario