ICP DAS USA CAN-2018C Manual de usuario

CAN-2018C Quick Start Ver. 1.1, Feb/2014

CAN-2018C Quick Start

Hardware Specification

CAN Interface

CANopen Specification

CiA DS-301 v4.02, DS-401 v2.1

No. of PDOs

10 Rx, 10 Tx (Support dynamic PDO)

PDO Mode

Event-triggered, Remotely-requested, Cyclic and acyclic SYNC

Node ID

1~99 selected by rotary switch

Baud Rate (bps)

10k, 20k, 50, 125k, 250k, 500k, 800k and 1M

Error Control

Node Guarding protocol and Heartbeat Producer protocol

Terminator Resistor

Switch for 120 Ω terminator resistor

Connector

5-pin screwed terminal block

(CAN_GND, CAN_L, CAN_SHLD, CAN_H, CAN_V+)

Analog Input

Channels

Input Type

+/- 15mV, +/- 50mV, +/- 100mV, +/- 500mV, +/- 1V, +/- 2.5V

+/-20mA (Requires Optional External 125 Ohms Resistor)

Thermocouple (J, K, T, E, R, S, B, N, C)

Resolution

16-bit

ESD Protection

+/-4 kV, Contact for each channel

LED

Status LED

PWR LED, RUN LED, ERR LED

Power

Input range

Unregulated +10 ~ +30 VDC

Power Consumption

1.5 W

Environment

Operating Temp.

-25 ~ 75 ℃

Storage Temp.

-30 ~ 80 ℃

Humidity

10 ~ 90% RH, non-condensing

For more information about CAN-2018C, please visit the following website:

http://www.icpdas.com/products/Remote_IO/can_bus/can-2018c.htm

CAN-2018C Quick Start Ver. 1.1, Feb/2014

CAN-2018C Pin Assignments

CAN-2018C Quick Start Ver. 1.1, Feb/2014

CAN-2018C Internal I/O Structure

CAN-2018C Quick Start Ver. 1.1, Feb/2014

CAN-2018C Wiring Connection Type

Note: When connecting to a current source, an optional external 125-Ohm precision

resistor is required.

CAN-2018C Quick Start Ver. 1.1, Feb/2014

CAN-2018C CAN Bus Wire Connection

*CAN_SHID (FG) is Optional.

2-Wire Connection

Signal

Description

CAN_V+

Power positive

CAN_H

Signal high of CAN Bus

line

CAN_SHLD

Cable Shield (FG)

CAN_L

Signal low of CAN Bus

line

CAN_GND

CAN ground

CAN-2018C Quick Start Ver. 1.1, Feb/2014

3-Wire Connection

4-Wire Connection (The CAN-2000 is powered by the master device)

CAN-2018C Quick Start Ver. 1.1, Feb/2014

CAN-2018C Firmware Update

Step 1 –Set Module to “Bootloader” mode (set Node ID to 00). Then power on the

module.

Step 2 –Run FW_Update_CAN Utility

(FW_Update_CAN Utility)

CAN-2018C Quick Start Ver. 1.1, Feb/2014

[1] CAN Device :

The below ICP DAS CAN products are supported by FW_Update_CAN utility

for firmware update.

(1) RS232 to CAN : I-7530

(2) Ethernet to CAN : I-7540D

(3) USB to CAN : I-7565, I-7565-H1, I-7565-H2

(4) CAN Card : PISO-CM100(U),

PISO-/PCM-/PEX-CAN200 / CAN400

Before firmware update, users need to set the below parameters.

(1) Select CAN hardware interface

(2) set Dev_Port or Board_ID

(3) set CAN_Port” number

[2] Download Firmware :

(1) Click “Browser…” button to choose firmware file, can_2018c_xx.fw.

(2) Click “Start Firmware Update” button to start firmware update and it will

show the total percentage of firmware update in progress bar. After the

firmware update finished, it will show the “Firmware Update Success !!”

message.

CAN-2018C firmware Download:

ftp://ftp.icpdas.com/pub/cd/fieldbus_cd/canopen/slave/can-2000c/can-2018c/

FW_Update_CAN Utility Download:

ftp://ftp.icpdas.com/pub/cd/fieldbus_cd/canopen/slave/can-2000c/tools/

Otros manuales de Sistema de E/S de ICP DAS USA

ICP DAS USA

ICP DAS USA tET-PD6 Manual de usuario

ICP DAS USA

ICP DAS USA I-7060 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

ICP DAS USA

ICP DAS USA tET Series Manual de usuario

ICP DAS USA

ICP DAS USA ISO-C64 Manual de usuario

ICP DAS USA

ICP DAS USA ISO-AD32H Manual de usuario

ICP DAS USA

ICP DAS USA PROFI-8455 Guía de configuración

ICP DAS USA

ICP DAS USA I-7043D Manual de usuario

ICP DAS USA

ICP DAS USA ET-2200 Series Manual de usuario

ICP DAS USA

ICP DAS USA PISO-813 Manual de usuario

ICP DAS USA

ICP DAS USA I-7061D Manual de usuario

ICP DAS USA

ICP DAS USA EIP-2019 Manual de usuario

ICP DAS USA

ICP DAS USA ET-2242 Manual de usuario

ICP DAS USA

ICP DAS USA CAN-8823 Manual de usuario

ICP DAS USA

ICP DAS USA PIO-D144 Series Manual de usuario

ICP DAS USA

ICP DAS USA I-7065BD Manual de usuario

ICP DAS USA

ICP DAS USA CAN-2084C Manual de usuario

ICP DAS USA

ICP DAS USA I-3591 Manual de usuario

ICP DAS USA

ICP DAS USA DB-16R Manual de usuario

ICP DAS USA

ICP DAS USA ET-2255U Manual de usuario

ICP DAS USA

ICP DAS USA ET-2242 Manual de usuario

ICP DAS USA

ICP DAS USA PISO-P64 Series Manual de usuario

ICP DAS USA

ICP DAS USA DGW-521 Manual de usuario

ICP DAS USA

ICP DAS USA EC2-P32 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario

WAGO

WAGO I/O-SYSTEM 750 Manual de usuario