ICP DAS USA I-7232D Guía de configuración

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----1

The I-7232D CANopen/Modbus Gateway

Quick Start User Guide

1. Introduction

This user guide describes how to implement the I-7232D module into

users’ applications in a quick and easy way. Therefore, it only provides the

basic instructions. If users want to know more detail information about the

I-7232D, please refer to the I-7232D user manual in the product CD or

download it from following web site:

http://www.icpdas.com/download/can/index.htm

The purpose of this manual is focused on helping users to quickly

familiarize themselves with the I-7232D module. Users can apply the I-

7232D module as follows.

CANopen

Device

PISO-CAN200/400

CPS_Modbus RTU

Gateway

CANopen

Salve

I-8421

PISO-CPM100

RS-485

Modbus RTU

(M-7000)

Modbus RTU

Master

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----2

2. Hardware structure

3. 7-segment LED

7-segment

LED Number

CAN Baud

rate

RS-485

Baud rate

0 10 K bps 1200 bps

1 20 K bps 2400 bps

2 50 K bps 4800 bps

3 125 K bps 9600 bps

4 250 K bps 19200 bps

5 500 K bps 38400 bps

6 800 K bps 57600 bps

7 1000 K bps 115200 bps

Bypass CAN

Bus Connector

7-segment

LED

RS-232 Port

(

connect to PC

)

Reserve for further use

RS-485 Baud rate:

Refer to the right

hand side table

CAN Baud rate:

Refer to the right

hand side table

Node ID:

0x00

(

)

~0x7F

(

127

)

n: Normal

Power Pin

RS-485 Port

(Connect to I/O modules)

Power LED

CAN Bus

Connector

CANopen

Status LED

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----3

4.How to Start

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----4

5.Configuration Installation

Step1: Install the CANopen/Modbus RTU Gateway Utility into your PC. Users can get

the setup file from the web site http://www.icpdas.com/download/can/index.htm or

the product CD in the path of “/Napdos/iCAN/CAN_Gateway/I-7232D”.

Step2: Before running the CANopen/Modbus RTU Gateway Utility, please connect the

COM1 of the I-7232D with the available COM port of your PC. Also, connect

the configured Modbus RTU modules with the COM2 of the I-7232D. The

architecture is displayed in the following figure.

(Note: We use the ICPDAS M-7000 series Modbus RTU modules for this demo, if users want to use any

other Modbus RTU device, please configure the communication parameters of this device firstly.)

Step 3: Turn off the I-7232D firstly. Connect the INIT* pin and the GND pin on the I-

7232D. Then, turn on the I-7232D.

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----5

Step 4: Run the CANopen/Modbus RTU Gateway Utility.

Step 5: Execute the CAN_MRU.exe file. The following figure will be displayed.

Then click the “connect” button.

(Note: When the CAN_MRU.exe can’t get the configuration information from the EEPROM, it may

response a Warning dialog as follows. This situation may be happen because the connection between

PC and I-7232D is broken during the CAN_MRU.exe is writing the data to the I-7232D EEPROM. Users

can repeat the steps from 2~5 to solve this problem)

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----6

Step 6: Click the “CAN Bus” button to configure the CAN communication parameters

for I-7232D.

Step 7: Click the “RS-485” button to configure the RS-485 parameters for the

CANopen/Modbus RTU gateway. These parameters need to match with the

communication parameters of Modbus RTU modules. Afterwards, click the

“Next” button to next step.

Step 8: You have to input the Modbus device NodeID, Relay Address, Register/Relay

Address and Data Length for one Modbus device connected with I-7232D.

These parameters are decided from this Modbus RTU device. Then click

“ADD” button to save the parameters settings. Repeat the action described

above if you have another Modbus device. When you finish these steps,

please click “Next” button to next step.

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----7

(Note: If you want to remove some device information, please select the instance number corresponding

to this device, and click the “Delete” button, the device information will be removed.)

Users can click on the “PDO Information” or “Modbus Information” button to view the PDO objects or

Modbus RTU devices configuration information. These information dialogs are shown below.

I-7232D CANopen/Modbus RTU Quick Start User Guide (Version 1.1,March/2006, I-7232D) -----8

Step 9: If everything is ok, click the “Finish” button to create the EDS file and save the

related information into the EEPROM of the I-7232D.

Step 10: Turn off the I-7232D, and remove the wire between the Init* pin and GND pin

of the I-7232D, Then power on the I-7232D. When the I-7232D has finished

the initialization, the RUN LED on the I-7232D will be flashed about twice per

second, and the I-7232D is into the NMT pre-operational state. For more

information about the CANopen system and CANopen communication set,

please refer to the I-7232D user manual.

Tabla de contenidos

Otros manuales de Puerta de ICP DAS USA

ICP DAS USA

ICP DAS USA GW-7838-M Manual de usuario

ICP DAS USA

ICP DAS USA GW-7552 Guía de configuración

ICP DAS USA

ICP DAS USA GW-7228 Manual de usuario

ICP DAS USA

ICP DAS USA HRT-310 Manual de usuario

ICP DAS USA

ICP DAS USA GW-7472 Guía de instalación

ICP DAS USA

ICP DAS USA GRP-520 Manual de usuario

ICP DAS USA

ICP DAS USA GRP-540M Manual de usuario

ICP DAS USA

ICP DAS USA GT-541 Manual de usuario

ICP DAS USA

ICP DAS USA HRT-711 Manual de usuario

ICP DAS USA

ICP DAS USA GW-7228 Manual de usuario

ICP DAS USA

ICP DAS USA GRP-2841M Manual de usuario

ICP DAS USA

ICP DAS USA GRP-540M Manual de usuario

ICP DAS USA

ICP DAS USA GW-2200 Series Manual de usuario

ICP DAS USA

ICP DAS USA RMV-511 Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2610 Manual de usuario

ICP DAS USA

ICP DAS USA GW-7553 Guía de configuración

ICP DAS USA

ICP DAS USA GW-5492 Manual de usuario

ICP DAS USA

ICP DAS USA GW-7553-B Manual de usuario

ICP DAS USA

ICP DAS USA GW-2139M Manual de usuario

ICP DAS USA

ICP DAS USA ECAN-240-FD Manual de usuario

ICP DAS USA

ICP DAS USA GW-7238D Manual de usuario

ICP DAS USA

ICP DAS USA I-7540D Manual de usuario

ICP DAS USA

ICP DAS USA SMS-531 Manual de usuario

ICP DAS USA

ICP DAS USA PFN-2000 Series Manual de uso y cuidado

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario