ICM Controls SC 2811 Instrucciones generales
3 Heat/2 Cool
Auto or Manual Changeover
Hardwired
SC 2811
Non-Programmable Electronic Thermostat
Installation, Operation & Application Guide
For more information on our complete range of American-made
products – plus wiring diagrams, troubleshooting tips and more,
visit us at www.icmcontrols.com
• Configurable
• Three Stage Heat / 2 Stage Cool Systems
• Multi-Stage Heat Pump Systems
• Backlit Display
• Field Temperature Calibration
• Filter Check
• Status Indicator Light
• Relay Outputs
(minimum voltage drop in thermostat)
• Ideally Suited for:
– Residential (New Construction/Replacement)
– Light Commercial
Table of Contents
Parts Diagram .............................................................................................................................1
Specifications .............................................................................................................................. 2
Important Safety Information .....................................................................................................2
Package Contents/Tools Required............................................................................................... 2
To Remove Existing Thermostat ................................................................................................3
To Install Thermostat ..................................................................................................................3
Remote Sensor Installation (Optional) ........................................................................................5
Terminal Designator Descriptions................................................................................................ 6
SC2811 Output Chart..................................................................................................................6
Wiring Diagrams..........................................................................................................................7
Wiring Diagram Conversions .....................................................................................................10
Configuration Mode...................................................................................................................22
Testing the Thermostat ............................................................................................................ 26
Mode of Operation ....................................................................................................................27
Operating Modes ...................................................................................................................... 28
Troubleshooting ........................................................................................................................ 29
1
Parts Diagram
R12
W1
O/B
Y1 W2 Y2 W3
S1
S2
2
Specications
Electrical rating: • 24 VAC (18-30 VAC) • 4 amp maximum total load
• 1 amp maximum per terminal
Temperature control range: 45°F to 90°F (7°C to 32°C) Accuracy: ± 1°F (± 0.5°C)
System configurations: 3-stage heat, 2-stage cool, heat pump, gas, oil, electric
Timing:
Anti-short Cycle:
5 minutes
Backlight Operation:
13 seconds after mode change or button press
Terminations: R, C, W1/O/B, Y1, W2, Y2, G, W3, S1, S2
Important Safety Information
WARNING!
:
Always turn off power at the main power supply before installing, cleaning, or removing
thermostat.
• This thermostat is for 24 VAC applications only; do not use on voltages over 30 VAC
• Do not short across terminals of gas valve or system control to test operation; this will damage your
thermostat and void your warranty
• All wiring must conform to local and national electrical and building codes
• Do not use air conditioning when the outdoor temperature is below 50 degrees; this can damage your
A/C system and cause personal injuries
• Use this thermostat only as described in this manual
Package Contents/Tools Required
Package includes: SimpleComfort®2811 thermostat on base, thermostat cover, wiring labels, screws and
wall anchors, Installation, Operation and Application Guide
Tools required for installation: Drill with 3/16” bit, hammer, screwdriver
3
To Install Thermostat
To Remove Existing Thermostat
ELECTRICAL SHOCK HAZARD
– Turn off power at the main service panel by removing the fuse
or switching the appropriate circuit breaker to the OFF position before removing the existing
thermostat.
1. Turn off power to the heating and cooling system by removing the fuse or switching the appropriate
circuit breaker off.
2. Remove cover of old thermostat. This should expose the wires.
3. Label the existing wires with the enclosed wire labels before removing wires.
4. After labeling wires, remove wires from wire terminals.
5. Remove existing thermostat base from wall.
6. Refer to the following section for instructions on how to install this thermostat.
ELECTRICAL SHOCK HAZARD
– Turn off power at the main service panel by removing the fuse
or switching the appropriate circuit breaker to the OFF position before removing the existing
thermostat.
IMPORTANT: Thermostat installation must conform to local and national building and electrical
codes and ordinances.
Note: Mount the thermostat about five feet above the floor. Do not mount the thermostat on an
outside wall, in direct sunlight, behind a door, or in an area affected by a vent or duct.
1. Turn off power to the heating and cooling system by removing the fuse or switching the appropriate
circuit breaker off.
4
To Install Thermostat (continued)
2. To remove cover, insert and twist a coin or screwdriver in the slots on the sides of the thermostat.
3. Put thermostat base against the wall where you plan to mount it (Be sure wires will feed through the
wire opening in the base of the thermostat).
4. Mark the placement of the mounting holes.
5. Set thermostat base and cover away from working area.
6. Using a 3/16” drill bit, drill holes in the places you have marked for mounting.
7. Use a hammer to tap supplied anchors in mounting holes.
8. Align thermostat base with mounting holes and feed the control wires through wire opening.
9. Use supplied screws to mount thermostat base to wall.
10. Insert stripped, labeled wires in matching wire terminals. See “Wiring Diagrams” and “Wiring Diagram
Conversions”sections of this manual (Pages 7-21).
CAUTION!
:
Be sure exposed portion of wires does not touch other wires.
11. Tighten screws on terminal block. Gently tug wire to be sure of proper connection. Double check that
each wire is connected to the proper terminal.
12. Seal hole for wires behind thermostat with non-flammable insulation or putty, or use an ICM insulated
wall plate (ACC-WP01).
13. Replace cover on thermostat by snapping it in place.
14. Turn on power to the system at the main service panel.
15. Test thermostat operation as described in “Testing the Thermostat” (Page 26).
5
Remote Sensor Installation (Optional)
1. Remove cover from remote sensor housing.
2. Select an appropriate location for mounting the remote sensor.
3. Mount remote sensor unit using hardware provided.
4. Install two wires between remote sensor and thermostat (use shielded cable).
• Wire 1 should run between the S1 terminal on the thermostat and the S1 terminal on the remote sensor
• Wire 2 should run between the S2 terminal on the thermostat and the S2 terminal on the remote sensor
5. Disable the main sensor (R12) on the thermostat by cutting it from the circuit board.
6
R – 24 VAC hot
C – 24 VAC common
W1/O/B – Configurable
W1 – 1st stage heat for non heat pump systems
O – cool active reversing valve
B – heat active reversing valve
Y1 – 1st stage cool, 1st stage heat for heat pumps
W2 – 2nd stage heat for non-hp, 3rd stage heat for 2 compressor heat pump systems
Y2 – 2nd stage cool for 2 compressor systems, 2nd stage heat for 2 compressor heat pump systems
G – Fan
W3 – 3rd stage heat for non-hp systems
Terminal Designator Descriptions
1ST Cool 2ND Cool 1ST Heat 2ND Heat 3RD Heat
Heat/Cool Y1,G YI,Y2,G W1,G* W1,W2,G* W1,W2,W3,G*
Heat Pump (One Compressor) Y1,G,O Y1,G,O Y1,G,B Y1,W2,G,B Y1,W2,W3,G,B
Heat Pump (Two Compressors) Y1,G,O Y1,Y2,G,O Y1,G,B Y1,Y2,G,B Y1,Y2,W2,G,B
Emergency Heat (Heat Pump Only) N/A N/A W2,G W2,W3,G N/A
* G not energized when configured as a gas/oil system
The SC2811 thermostat is configurable for all systems. The configuration directly affects the outputs.
Use the output chart to correctly configure and wire the thermostat to your system.
SC2811 Output Chart
7
First
Cooling Control
Second
Cooling Control
Wiring Diagrams
Third
Heating Control
Second
Cooling Control
Second
Heating Control
First
Cooling Control
First
Heating Control
8
Third
Heating Control
Second
Heating Control
First
Heating Control
Third
Heating Control
Second
Heating Control
First
Heating Control
Tabla de contenidos
Otros manuales de Termostato de ICM Controls
ICM Controls
ICM Controls SC1600L Manual de usuario
ICM Controls
ICM Controls SimpleComfort SC2211L Manual de usuario
ICM Controls
ICM Controls SC 5811 Instrucciones generales
ICM Controls
ICM Controls MP2010L Instrucciones generales
ICM Controls
ICM Controls SC 5011 Instrucciones generales
ICM Controls
ICM Controls SC3211L Instrucciones generales
ICM Controls
ICM Controls SC 3201 Instrucciones generales
ICM Controls
ICM Controls SC710 Instrucciones generales
ICM Controls
ICM Controls FS1500L Instrucciones generales
ICM Controls
ICM Controls SC 1800 Instrucciones generales
ICM Controls
ICM Controls SC3000L Instrucciones generales
ICM Controls
ICM Controls SC3000L Manual de usuario
ICM Controls
ICM Controls SC2201 Instrucciones generales
ICM Controls
ICM Controls SC4812 Manual de usuario
ICM Controls
ICM Controls SC1901L Instrucciones generales
ICM Controls
ICM Controls SC 1901 Instrucciones generales
ICM Controls
ICM Controls SC1800L Manual de usuario
ICM Controls
ICM Controls SC 3006 Instrucciones generales
ICM Controls
ICM Controls SC4010 Instrucciones generales
ICM Controls
ICM Controls SC 3000 Instrucciones generales
Manuales populares de Termostato de otras marcas
EWELLY
EWELLY EW-181 Manual de usuario
Prolon
Prolon T1100 Instrucciones de instalación
Computherm
Computherm Q20 Manual de usuario
Heatmiser
Heatmiser neoStat Manual de usuario
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario
