ICM Controls SC 2300 Instrucciones generales
2 Heat/2 Cool
Non-Programmable
Manual Changeover
SC 2300
Non-Programmable Electronic Thermostat
Installation, Operation & Application Guide
For more information on our complete range of American-made
products – plus wiring diagrams, troubleshooting tips and more,
visit us at www.icmcontrols.com
• Up to two-stage heat / two-stage cool
• Mercury-free, environmentally safe
• For use with 24 VAC systems
• Non-heat pump
• Manual Changeover
• Compatible with Gas, Oil, or Electric
Table of Contents
Parts Diagram ............................................................................................................................. 1
Specifications .............................................................................................................................. 2
Important Safety Information ..................................................................................................... 2
Package Contents/Tools Required............................................................................................... 3
General Description..................................................................................................................... 3
Features/Benefits........................................................................................................................ 3
To Remove Existing Thermostat ................................................................................................ 4
To Install Thermostat .................................................................................................................. 4
Installing and Changing Batteries................................................................................................ 6
Replacing Wiring Labels .............................................................................................................. 6
Operation .................................................................................................................................... 7
Setting the Setpoint Temperature .............................................................................................. 7
Setting a New Temperature Differential...................................................................................... 7
Changing Fahrenheit to Celsius................................................................................................... 8
Starting the Thermostat ............................................................................................................. 8
LED Indicator .............................................................................................................................. 9
Wiring Diagrams........................................................................................................................ 10
Troubleshooting ........................................................................................................................ 12
CAUTION!
:
This thermostat should be installed by trained technicians only.
Adhere to all local and national codes. Disconnect all power to the
system before installing, removing, or cleaning.
1
Parts Diagram
Mode Switch or
Cool/Off/Heat Switch
Fan Switch
Gas/Electric
Switch
Battery
Compartment
Celsius/
Fahrenheit
Jumper
RH
ONAUTO
2300
F–C
CRCY2 W2 Y1 W1G
Up Button Down Button
2
Specications
Input:
• Voltage: 24 VAC (18-30 VAC)
• DC Power: 3.0 VDC (2 “AA” alkaline batteries included)
Output:
• Maximum: 1 amp per terminal (3 amp total for all terminals)
• Temperature control ranges: 45°F to 90°F (7°C to 32°C)
Accuracy: ± 1°F (± 0.5°C)
• System configurations: Multi-stage – Two-stage heat or two-stage cool
• Terminations: RH, RC, W1, W2, Y1, Y2, G, C
SET
ROOM
LO BAT
DIFF
Low battery indicator
Temperature
differential setting
Room temperature
Room temperature
setpoint
Important Safety Information
• Always turn off power at the main power source by unscrewing fuse or switching circuit breaker to the off
position before installing, removing, cleaning, or servicing this thermostat
• Read all of the information in this manual before installing this thermostat
• This thermostat should be installed only by a professional contractor
• This is a 24 VAC low-voltage thermostat; do not install on voltages higher than 30 VAC
• All wiring must conform to local and national building and electrical codes and ordinances
• Do not short (jumper) across terminals on the gas valve or at the system control to test installation; this will
damage the thermostat and void the warranty
• Do not switch system to cool if the temperature is below 50°F (10°C) This can damage the air conditioning
system and may cause personal injury
• The thermostat will not control your heating/air conditioning system without power; it requires two charged
“AA” batteries for thermostat operation and a continuous 24 VAC circuit for proper system control
• Replace batteries every year or when the low battery indicator appears on the thermostat’s display
• Use this thermostat only as described in this manual
3
Features/Benets
General Description
Package includes: SimpleComfort®2300 non-programmable thermostat on base, thermostat cover, wiring
labels, screws and wall anchors, Installation, Operation and Application Guide.
Tools required for installation: Drill with 3/16” bit, hammer, screwdriver.
Package Contents/Tools Required
The SimpleComfort®2300 is intended to operate and is compatible with 24 VAC residential systems with
up to 2-stage heat/2-stage cool. It will operate with multi-stage systems that are manual changeover.
There are no optional items required for standard installations. This thermostat is also compatible as a
master thermostat in zoned system applications.
The SimpleComfort®2300 will automatically control the heat and/or air conditioning system. When used
properly, this thermostat can reduce heating and cooling costs throughout the year.
• The SimpleComfort®2300 thermostat is a digital, mercury-free, non-programmable, electronic thermostat
• Compatible with multi-stage heating/cooling systems; works with gas, oil, or electric systems
• Compatible as a master thermostat in zoned system applications
• Visual low battery indication
• Automatic Heating System Shutdown: If temperature exceeds 90°F (32°C)
• System Customization: Choose Fahrenheit or Celsius display; three available temperature differential
settings
4
ELECTRICAL SHOCK HAZARD
– Turn off power at the main service panel by removing the fuse
or switching the appropriate circuit breaker to the OFF position before removing the existing
thermostat.
1. Turn off power to the heating and cooling system by removing the fuse or switching off the appropriate
circuit breaker.
2. Remove cover of old thermostat. This should expose the wires.
3. Label the existing wires with the enclosed wire labels before removing wires.
4. After labeling wires, remove wires from wire terminals.
5. Remove existing thermostat base from wall.
6. Refer to the following section for instructions on how to install this thermostat.
To Remove Existing Thermostat
ELECTRICAL SHOCK HAZARD
– Turn off power at the main service panel by removing the fuse
or switching the appropriate circuit breaker to the OFF position before removing the existing
thermostat.
IMPORTANT: Thermostat installation must conform to local and national building and electrical
codes and ordinances.
Note:
Mount the thermostat about five feet above the floor. Do not mount the thermostat on an
outside wall, in direct sunlight, behind a door, or in an area affected by a vent or duct.
1. Turn off power to the heating and cooling system by removing the fuse or switching off the appropriate
circuit breaker. Move the Cool/OFF/Heat switch to OFF
.
To Install Thermostat
5
To Install Thermostat (continued)
2. Move the FAN AUTO/ON switch to AUTO.
3. To remove cover, insert and twist a coin or screwdriver in the slots on the sides of the thermostat.
4. Put thermostat base against the wall where you plan to mount it (Be sure wires will feed through the
wire opening in the base of the thermostat).
5. Mark the placement of the mounting holes.
6. Set thermostat base and cover away from working area.
7. Using a 3/16” drill bit, drill holes in the places you have marked for mounting.
8. Use a hammer to tap supplied anchors into mounting holes.
9. Align thermostat base with mounting holes and feed the control wires through wire opening.
10. Use supplied screws to mount thermostat base to wall.
CAUTION!
:
Be sure exposed portion of wires does not touch other wires.
11. Tighten screws on terminal block. Gently tug wire to be sure of proper connection. Double check that
each wire is connected to the proper terminal.
12. Seal hole for wires behind thermostat with non-flammable insulation or putty.
13. Set the Gas/Electric switch to electric or gas/oil.
14. Set the temperature scale jumper to Fahrenheit or Celsius.
CAUTION!
:
Installing batteries incorrectly can damage thermostat.
15. Install two “AA” alkaline batteries.
16. Replace cover on thermostat by snapping it in place.
17. Turn on power to the system at the main service panel.
6
If your LCD is blank, or displaying LO BAT, the batteries are not installed or need to be changed. We
suggest you change the batteries at least once a year, or whenever the LO BAT warning displays.
Note: After installing new batteries, you have to reset the room temperature setting and the
differential setting.
Step 1: Move the Cool/Off/Heat switch into the Off position.
Step 2: Move the Fan Auto/On switch into the Auto position.
Step 3: Remove the cover, and install the two “AA” alkaline batteries into the battery compartment.
Proper battery installation is important! Make sure the positive ends of the batteries match the
positive terminals in the battery compartment.
If the display is on, the batteries are installed properly.
Replace the old labels with the enclosed new labels:
Old New Type
R, V-VR or VR-R RH 24 VAC, heat transformer
Y, Y1 or M Y1 Stage 1 cooling
G or F G Fan contactor circuit
Y2 Y2 2nd stage cooling control
W1, W2 or W-U W2 2nd stage heating control
C, X or B C 24 VAC, transformer common side
W1 W1 Stage 1 heating
RC 24 VAC, cool transformer
Installing and Changing Batteries
Replacing Wiring Labels
7
Setting the Setpoint Temperature
Step 1: Press the or button; the current temperature setpoint displays.
Step 2: Press the or button until the desired temperature setpoint displays.
Note:
Holding down either
the or button will scroll the
temperature display.
The new temperature setting is automatically saved. After 5 seconds, the display
returns to showing the current room temperature.
Setting a New Temperature Differential
IMPORTANT: The default temperature differential is factory set at 1°F. When your room temperature
varies by 1°F, the thermostat turns your system on. If you notice your system turning on and
off too frequently, increase the temperature differential accordingly.
Step 1: Remove the cover and the batteries.
Step 2: Reinstall the batteries and the cover. The display will show
This is the temperature differential setting.
Step 3: Press the or button to adjust the temperature differential down or up.
The display will return to the room temperature
display five seconds after the last input. The new
temperature differential setting will be saved.
Differential Setting °F °C
11°F 0.5°C
22°F 1.0°C
33°F 1.5°C
Operation
8
Operation (Continued)
Changing Fahrenheit to Celsius
The temperature displays in degrees Fahrenheit as a factory set default. Follow these steps to change to
degrees Celsius:
Step 1: Remove the cover and the batteries.
Step 2: Move the F/C jumper to the desired position, For Cusing the center pin as a common.
Step 3: Reinstall the batteries and the cover.
Your LCD readout changes accordingly.
Starting the Thermostat
Step 1: Move the Fan switch into the Auto position.
• In Auto, indoor fan runs only during a heating or cooling cycle
• In ON, indoor fan runs continuously
Step 2: Move the Mode switch to either Cool or Heat position, depending on
the season. The thermostat will now operate and maintain the room
temperature at the desired setpoint.
Note:
When the thermostat operates the system, there is built-in
compressor protection. After the compressor turns off, the
system will not turn it back on for about five minutes. This
protects the compressor.
Cool Off Heat
Mode
Auto On
Fan
Tabla de contenidos
Otros manuales de Termostato de ICM Controls
ICM Controls
ICM Controls SC 2000 Manual de usuario
ICM Controls
ICM Controls SimpleComfort PRO SC5812 Manual de usuario
ICM Controls
ICM Controls SC4812 Manual de usuario
ICM Controls
ICM Controls SC3211L Instrucciones generales
ICM Controls
ICM Controls MP2211L Manual de usuario
ICM Controls
ICM Controls SC900V Instrucciones generales
ICM Controls
ICM Controls SC1901L Instrucciones generales
ICM Controls
ICM Controls SC2000L Instrucciones generales
ICM Controls
ICM Controls SC1800L Manual de usuario
ICM Controls
ICM Controls SC4010 Instrucciones generales
ICM Controls
ICM Controls SC4011 Instrucciones generales
ICM Controls
ICM Controls SC 3201 Instrucciones generales
ICM Controls
ICM Controls MP5010 Instrucciones generales
ICM Controls
ICM Controls SC4011 Manual de usuario
ICM Controls
ICM Controls SC2201 Instrucciones generales
ICM Controls
ICM Controls SC 2000 Instrucciones generales
ICM Controls
ICM Controls SC1600L/VL Manual de usuario
ICM Controls
ICM Controls SC 2001 Instrucciones generales
ICM Controls
ICM Controls SC 4211 Instrucciones generales
ICM Controls
ICM Controls ICM I3 Instrucciones de instalación y funcionamiento
Manuales populares de Termostato de otras marcas
EWELLY
EWELLY EW-181 Manual de usuario
Prolon
Prolon T1100 Instrucciones de instalación
Computherm
Computherm Q20 Manual de usuario
Heatmiser
Heatmiser neoStat Manual de usuario
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario
