IBM Flex System EN2092 Manual de usuario

Configuring the IBM Flex System EN2092 1Gb Ethernet Sc l ble Switch

Prerequisites:

One IBM Flex System Enterprise Chassis, one IBM Flex System EN2092 1Gb Ethernet S alable

Swit h installed in I/O module bay 1 or 2.

An Ethernet network is already onfigured.

Steps:

Note: This pro ess illustrates how to enable the swit h ports through the Chassis Management Module

(CMM) ommand-line interfa e. For information about using the CMM interfa e, you an use the

“Configuring IBM Flex System Enterprise Chassis omponents” qui k start guide. You an find that qui k

start guide at this lo ation:

In the information enter (Internet):

http://pi .dhe.ibm. om/info enter/flexsys/information/topi / om.ibm.a . ommontasks.do / ommonta

sks_ hassis_ onfig.html

The IBM Flex System produ t do umentation is also available on the IBM Flex System Manager management node. To a ess

the installed do umentation, li k Information Center from the IBM Flex System Manager Home page and then navigate to:

IBM Flex System information -> Qui k start guides -> Installing and onfiguring the IBM Flex System Enterprise Chassis

1. Log on to the Chassis Management Module (CMM) CLI with an SSH appli ation. The default IP

address is 192.168.70.100 and the default login/password is USERID/PASSW0RD. If ne essary, obtain

the IP address and login of the CMM from your system administrator.

2. Set the environment to the bay where you installed the swit h. The following example is for bay 2:

env -T system:swit h[2]

3. Run the following ommand to enable external data ports:

if onfig -ep enabled

External ports 1 – 10 are now enabled for data throughput.

Page 1 of 2

Activating additional keys:

If you have pur hased additional keys, they need to be installed on the swit h. Complete the following

steps to install additional keys using the ISCLI interfa e.

1. To retrieve the key, navigate a browser to https://www.ibm. om/systems/x/fod/index.wss and sign in

with your ID and password

2. Cli k Request activation key.

3. Enter the authorization ode. The authorization ode was supplied to you by email or on paper as

part of the ordering pro ess.

4. Cli k Continue and follow the instru tions and download the key file.

5. Log on to the EN2092 swit h with an SSH appli ation. The default IP addresses for the swit h

through the CMM are as follows: 192.168.70.120 (bay 1), 192.168.70.121 (bay 2), 192.168.70.122

(bay 3), and 192.168.70.123 (bay 4). If ne essary, obtain the IP address and login of the swit h from

your system administrator.

6. Enter ena.

7. Enter software-key.

8. Enter enakey address <hostname or IP address> keyfile <file name>

protocol tftp mgt-port

Note: you must reset the swit h to apply the key.

9. Reset the swit h. Enter reload..

Repeat the step for additional keys if needed. The sequen e of steps is shown here:

Router#ena

Router(config)#software-key

Router(Software-Key)#enakey address 9.44.143.206 keyfile

ibm_fod_0007_ 010CM28N001_anyos_noarch.key protocol tftp mgt-port

Starting download key file...

Key file download complete (494 bytes)

Software feature Upgrade1 will be Active upon next reboot.

Aug 5 11:47:39 1080:0:0:0:0:0:0:82 NOTICE mgmt: Software feature Upgrade1

will be Active upon next reboot.

A Reboot is required for the new settings to take effect.

Router(Software-Key)#reload

...

Resetting at 11:47:59 Tue Aug 5, 2014...

Page 2 of 2

Otros manuales para Flex System EN2092

Tabla de contenidos

Otros manuales de Cambiar de IBM

IBM

IBM 3110X - Cisco Catalyst Switch Manual

IBM

IBM 612 Manual de usuario

IBM

IBM Redbooks G8264CS Manual de usuario

IBM

IBM 8265 Manual de usuario

IBM

IBM 8270 600 Manual de usuario

IBM

IBM 8271 Nways Ethernet LAN Switch Manual de usuario

IBM

IBM Nways 8260 Manual de usuario

IBM

IBM T860 Manual de usuario

IBM

IBM F16 Manual de usuario

IBM

IBM BROCADE 4 GB FC HBAS Manual de usuario

IBM

IBM RackSwitch G8000 Manual de usuario

IBM

IBM SAN40B-4 - System Storage Switch Guía de solución de problemas

IBM

IBM Brocade FCoE Manual de usuario

IBM

IBM 24R9718 IB Manual de usuario

IBM

IBM 8237 Manual de usuario

IBM

IBM J08E Manual de usuario

IBM

IBM RedBooks SAN24B-5 Manual

IBM

IBM 2498B24 - System Storage SAN24B-4 Switch Manual

IBM

IBM Nortel Networks L2/3 Manual de usuario

IBM

IBM 8285 Nways Manual de usuario

IBM

IBM 2498B24 - System Storage SAN24B-4 Switch Manual

IBM

IBM G8124E Manual de usuario

IBM

IBM RedBooks SAN24B-5 Manual de usuario

IBM

IBM Flex System EN4023 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario