IBM REDPAPER P5 520 Manual de usuario

Quick start guide for p5 520 (9131-52A)

IBM Systems

Rack-mounted devices are not to be used as a shelf or workspace. Do not place

any object on top of rack-mounted devices.

CAUTION: The weight of this part or unit is between 32 and 55 kg (70.5 and

121.2 lb). It takes three persons to safely lift this part or unit. (C010)

The exclamation mark surrounded by a gray triangle denotes caution. A CAUTION

notice indicates the presence of a hazard that has the potential of causing

moderate or minor personal injury. Before doing a step that contains a caution icon,

read and understand the caution statement that accompanies it.

1Before you begin

Use safe practices when lifting.

This Quick start guide contains an abbreviated set of setup instructions designed to help you quickly

unpack and set up a standard system. Users unfamiliar with this IBM hardware should use the fully

detailed, setup instructions that you can find in the IBM Systems Hardware Information Center. For

details about how to access the information center, see task 9 .Finish your system setup

Tools needed (Rack installation only)

Flat-blade screwdriver

32-55 kg (70.5-121.2 lbs)

2.1

2.2

Inventory

Complete an inventory of the external parts.

Locate the kitting report (inventory list) in the bag that contains the information

center CD (SK3T-8159). Make sure you received all of the parts that you ordered.

Your order information should be located in an envelope adhered to the outside of

your system box. You can also obtain order information from your marketing

representative or IBM Business Partner.

If you have incorrect, missing, or damaged parts, consult any of the following

resources:

If you are not installing your server into a rack, skip to task 7

Cable the

HMC and the server

Your IBM reseller

IBM Rochester manufacturing automated information

line at 1-800-300-8751 (United States only)

Directory of worldwide contacts at www.ibm.com/planetwide.

Select your location to view the service and support contact information.

Rack-mounting template

Slide rail assemblies

Rack-mounting hardware kit

Blue knobs

System-to-slide-rail screws

Rack-retaining screws

Blue thumb screws

Latch brackets

Latch-bracket screws

Cable-management arm

If you are installing your server into a rack, you will need the following parts:

3.1

3.2

3.3

If you are installing your server into a new rack, ensure that you have completed the

unpacking instructions that were provided with the rack.

If your server is already installed in a rack, skip to task 7

Place the rack in the location of the installation.

Use the wrench that was provided with your rack to level the rack by raising or

lowering the front and back leveling feet .

Install the stabilizer bracket on the front of the rack.

If necessary, remove any trim kit pieces that were previously installed on the

rack. Removing the trim kit pieces allows you to read the EIA units on the rack.

Tip:

Cable the HMC and the

server.

3.4

3Prepare the rack for installation

4.1

4.2

Locate the rack-mounting template, the rack-mounting hardware kit, and the slide

rail assemblies that were included with your server.

Use the rack-mounting template to determine where in the rack to place the server.

Remove any filler panels necessary to allow adequate access to the location

where you will install your server.

If you do not have enough space around your rack to open the front and back doors

completely, remove the doors before starting this task to allow adequate access.

Install the slide rail assemblies

4.3 Follow the rack-mounting template to mark the

location on the rack where you will place the

server. Use the self-adhesive placement dots

found on the rack-mounting template.

Pull the back latch-assembly

release tabs to the retracted

position and lock the latch

assembly . Make sure the

alignment pins that are located

on the back of the slide rail are

fully retracted.

From the back of the rack, insert

the front alignment pin into the

hole in the front of the rack, as

identified by the self-adhesive

placement dot.

Front

Back

Note: Install units into the lower part of the rack first.

Place larger and heavier units in the lower part of the

rack.

4.4 Install the slide rail assemblies .A

4.6

4.7

4.5

From the front, finger-tighten one of the rack-retaining screws in the first hole

above the front alignment pin .

From the front, attach the system-unit-

latch bracket by inserting the hook

into the rack hole above the hole

where you will place the latch bracket

screw. Finger-tighten the screw.

Align the retracted back pins with the holes as identified by the self-adhesive

placement dot. Place the rack flange between the slide-rail flange and the

retracted alignment pins .

Press the back latch-assembly-release tab to extend the back alignment pins into

the back of the rack.

From the back, finger-tighten one of the rack-retaining screws in the hole that

is located between the two back alignment pins .

4.8 Repeat steps 4.4 through 4.7 for

each slide rail assembly.

Actual size

part 26H7213

Actual size

part 12J5289

Actual size

part 12J5289

Actual size

part 04N6485

Before you begin: Read this entire task before completing any individual steps.

5.1

5.2 Fully extend both slide rails.

5.3 Lift the server using the handles on each side and position the server on the

extended slide rails. Align the three holes of the inner slide rails with the three holes

on each side of the server.

5.4

5.5 Remove the four blue knobs .B

Use safe practices when lifting.

Attach the four blue knobs to the server The blue knobs are used temporarily

to rest the server on the slide rails for installation. These knobs will be removed after

the server is secured to the slide rails.

BA.

Install the server onto the slide rail assembly

Before installing the server onto the slide rail assembly, ensure that the

leveling feet are extended and that the stabilizer bracket is correctly installed

to prevent the rack from falling forward.

Using a screwdriver, attach the inner slide

of the slide rails to each side of the

server by using the system-to-slide-rail

screws . Use a screwdriver to tighten

each of the screws.

5.7 Using a screwdriver, tighten the two rack-retaining screws to secure the slide rails to

the back of the rack.

5.6 Simultaneously release the blue safety

latches located near the front of each

slide rail assembly, and slowly push the

server back into the rack.

5.8 Slide the server part of the way out of the rack. Using a screwdriver, tighten the front

two rack-retaining screws and the two latch-bracket screws on the front of the rack to

secure the slide rails.

32-55 kg (70.5-121.2 lbs)

Tip: Pull the server back out and push it in again to make sure that the slide

rails are aligned correctly and that it glides smoothly.

6Install the cable-management arm

6.3

From the back of the rack, use the pin to affix the cable-management arm to the

left slide-rail management arm flange that is attached to the rack frame .

D-

6.1 Locate the cable-management arm and the two pins .EA

6.2

Use the second pin to affix the other end of the cable-management arm to the

flange that is attached to the sliding portion of the left slide rail assembly .

Tip: If space is limited inside the rack, slide the server out part of the way to install the

cable-management arm.

7.1

7.2

7.3

Route the power cords through the rings or clamps on the

back of the server, and connect to the server, monitor, and HMC.

, if available,

not connect the power cords to a power source until instructed to

do so.

7.4 Attach the monitor cable to the monitor connector on the HMC

and tighten the screws.

Tip: If you are using the rack-mounted LCD monitor and

keyboard (7316-TF3), use the C2T-to-KVM adapter breakout

cable to attach to the HMC.

A Hardware Management Console (HMC) is a system that connects to the server and manages it

through a network.

If you are using a rack-mounted HMC, these steps assume it is already installed in the rack.

If you need to install the HMC into the rack, follow the instructions in the IBM Systems Hardware

Information Center, and return to this guide when you are ready to begin cabling your HMC. For details

about how to access the information center, see task 9

If you are not using an HMC to manage your server, you can use the Integrated

Virtualization Manager (IVM), a graphics terminal, or an ASCII terminal. If you plan to use

IVM, which allows you to create and manage partitions, skip to task 8

. For information about the other console

options, go to the IBM Systems Hardware Information Center. For details about how to

access the information center, see task 9 .

Cable the server and

access the Integrated Virtualization Manager

Finish your system setup

Finish your system setup.

If you are using any optional adapters for the HMC, connect the cables to the

appropriate adapter connectors in the PCI slots of your server and HMC.

Cable the HMC and the server

Important: Ensure that if there is a voltage switch next to the power

connector on the monitor, it is in the appropriate position for the voltage used

in your geography.

Connect the mouse and keyboard cables to the appropriate ports on the

back of the HMC. If your mouse and keyboard use Universal Serial Bus

(USB) cables, you can connect these to the ports on the front of the HMC.

7.5

7.6

If you are not using a modem, skip to step 7.6.

If you are using the integrated HMC modem, connect the telephone cable to

the modem and to the analog jack on the wall. If you are using an external

modem, connect the modem data cable to the external modem and to a serial

port on the HMC. Then connect the telephone cable to the external modem

and to the analog jack on the wall.

Connect the Ethernet cable to the Ethernet port on the HMC and to

the Ethernet port labeled HMC1 on the server.

For a stand-alone HMC, use the integrated Ethernet port. For the 7310-CR2

rack-mounted HMC, use the bottom-right Ethernet port. For the 7310-CR3 rack-

mounted HMC, use the left port of the two planar board Ethernet ports.

7.7

7.8

7.9

If using an external modem, plug the power cord into the modem.

Plug the power cords for the monitor, HMC, and external modem into a power

source. Do not connect the server to a power source until instructed to do so.

CAUTION: This product is equipped with a 3-wire (two conductor and a

ground) power cable and plug. Use this power cable with a properly

grounded electrical outlet to avoid electrical shock. (C018)

You have completed the basic setup. Go to task 9 Finish your system setup.

Route the cables through the cable-management arm on the server and

secure the cables with the straps provided.

7.12

7.10

7.11

Start and configure the HMC, which includes the Guided Setup Wizard. You can

find the instructions for configuring the HMC in the IBM Systems Hardware

Information Center. For details about how to access the information center, see

task 9 Finish your system setup.

Connect the server to a power source and wait for the control panel on the front of

the server to display This might take several minutes..01

Press the white Power On button on the control panel.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Servidor de IBM

IBM

IBM System x3300 M4 Manual

IBM

IBM RS/6000 7025 F50 Series Manual de usuario

IBM

IBM Power System 9009-22G Manual de usuario

IBM

IBM BladeCenter HS23 Manual de usuario

IBM

IBM System x iDataPlex dx360 Manual de usuario

IBM

IBM eServer xSeries 225 Type 8647 Manual de usuario

IBM

IBM HS12 - BladeCenter - 8028 Manual de usuario

IBM

IBM System Storage TS7650G 3958 DD4 Manual de usuario

IBM

IBM x3455 - System - 7984 Manual de usuario

IBM

IBM 7944 Manual de usuario

IBM

IBM System x3755 M3 7164 Manual de usuario

IBM

IBM 72332SU Manual de usuario

IBM

IBM 8500R - Netfinity - 8681 Manual del propietario

IBM

IBM X 330 Series Manual de usuario

IBM

IBM QS21 - BladeCenter - 0792 Manual de usuario

IBM

IBM BladeCenter JS12 7998 Manual de usuario

IBM

IBM Eserver pSeries 670 Manual de usuario

IBM

IBM Power System LC922 Manual de usuario

IBM

IBM System x3650 M4 Type 7915 Manual de usuario

IBM

IBM Power 720 Express Guía de instalación

IBM

IBM Netfinity 3000 Manual de instrucciones

IBM

IBM BladeCenter PS703 Guía de instalación

IBM

IBM 787264U Manual de usuario

IBM

IBM 88631SU - System x3850 - 8863 Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario