IBM TotalStorage NAS 200 25T Manual de programación

IBM TotalStorage NAS 200

Model 25T

Quick Start Instructions



First Edition (October 2002)

US Government Users Restricted Rights – Use, duplication or disclosure restricted by

GSA ADP Schedule Contract with IBM Corp.

IBM TotalStorage

™

NAS 200Model 25T Quick Start

Instructions

Step 1: Read this first

Caution:

—Safety Information

Use safe practices when lifting this product.

Do not place any object weighing more than 82 kg (180 lb.) on top of

rack-mounted devices.

Notes:

1. Make sure the rack is stabilized before installing hardware, and always

load it starting at the bottom and moving upward to the top.

2. Visually inspect the unit to ensure that it was not damaged during

shipping. If any items are missing or damaged, contact your IBM

representative.

Step 2: Unpack the box

Items you find in the box (tower and rack configurations):

vModel 25T

vTwo power cables

IBM TotalStorage NAS 200

Hardware Installation Guide

Software CD

Documentation CD

vOne set of documentation including: Caution: Safety

Information – Read This First, IBM TotalStorage NAS 200

Hardware Installation Guide, Quick Start Instructions and

product and documentation CD-ROMs.

Rack configuration only

vOne rack installation kit including: Cable-management

assembly, cable straps, cable ties, cage nuts, clip nuts,

screw packages and slide rails and Rack Mounting

Instructions.

Items you provide

vOne Phillips #2 screwdriver

vOne flat-blade screwdriver

vOne One Ethernet cable (Cat5 copper cable if you are

using a copper Ethernet adapter) with connection

instructions and IP information from your network

administrator.

vOne PC with a subnetwork connection, Windows 2000

or Windows NT 4.0 or later, Swing and XML Java

libraries, Advanced Appliance Configuration application,

and Universal Management Services browser.

Optional service and diagnostic equipment

vOne monitor, keyboard and a PS/2 mouse

2NAS 200 Model 25T Quick Start Instructions

Step 3: Install the appliance

1. Tower configuration only: Place the tower configuration in its final location

and then go to “Step 4: Attach cables (Tower configuration)”on page 6.

Rack configuration only: Mark the rack-configuration location on the rack

by placing the provided stickers over the holes on the front and rear of the

rack indicated by the arrows on the template.

2. Insert the cage nuts using a screwdriver or the cage-nut insertion tool (or

slide on the clip nuts) into each marked hole.

IBM TotalStorage

™

NAS 200Model 25T Quick Start Instructions 3

3. Align each slide rail to the rack using the pin as a guide. Then bolt the

slide rails to the rack using the M6 screws provided.

4. Attach the hinge bracket to the rear of the rack using the M6 screws

provided. Then attach the cable-management assembly to the slide rail by

sliding the hinge pin into the hinge.

4NAS 200 Model 25T Quick Start Instructions

5. Place the engine in the rack by fully extending the slide rails out of the

rack, lifting the engine above the rails, and resting the rack-support wheels

on the slide rails. Then lower the front of the engine onto the slide rails,

ensuring that the bracket notches on the front of the engine fit securely on

the tabs located on the front of the slide rails.

6. Secure the appliance to the rails using the M4 screws provided. Unscrew

the rack-support wheels and store them in a safe place. Go to “Step 5:

Attach cables (Rack configuration)”on page 7.

IBM TotalStorage

™

NAS 200Model 25T Quick Start Instructions 5

Step 4: Attach cables (Tower configuration)

1. Connect the engine to your network by plugging the network cables to the

Ethernet ports and then into your network. Connect each power cable to

the receptacles on the back of the engine and then to different power source

outlets.

2. Route the power and network cables through the cable-restraint brackets on

the rear of the appliance. Go to “Step 7: Power on and verify LED status”

on page 9.

6NAS 200 Model 25T Quick Start Instructions

Step 5: Attach cables (Rack configuration)

1. Connect the engine to your network by pressing in on the safety latches,

sliding the engine halfway into the rack, and plugging the network cables

to the Ethernet ports and then into your network. Connect each power

cable to the receptacles on the back of the engine and then to different

power source outlets.

2. Route the cables through the cable-management assembly on the rack.

IBM TotalStorage

™

NAS 200Model 25T Quick Start Instructions 7

Step 6: Complete the installation

Rack configuration only

Complete the installation by sliding the engine into the rack until the release

latches snap shut. Then insert the M6 screws provided through the

release-latch-bracket assembly on either side of the engine.

Note: Inserting the M6 screws is required if the rack is moved or in a

vibration-prone area.

8NAS 200 Model 25T Quick Start Instructions

Tabla de contenidos

Otros manuales de Hardware de red de IBM

IBM

IBM TotalStorage DS300 Manual de usuario

IBM

IBM Proventia Management SiteProtector SP1001 Manual de usuario

IBM

IBM NEXUS 5000 - OVERVIEW 19-10-2010 Manual de usuario

IBM

IBM TotalStorage 201 Hoja de información del producto

IBM

IBM System Cluster 1350 Instrucciones de instalación y mantenimiento

IBM

IBM 8687-3RY Manual de usuario

IBM

IBM 2078-4F4 Manual de usuario

IBM

IBM Storwize V3500 Manual de usuario

IBM

IBM 16/4 Token Ring PCI Special NIC Instrucciones de uso

IBM

IBM DualPort TR Controller NetFlex-2 Instrucciones de uso

IBM

IBM J36S Manual de usuario

IBM

IBM 37L1415 Manual de usuario

IBM

IBM 3192-G Manual

IBM

IBM 32R1860 - Nortel Layer 2/3 Copper GbE Switch... Manual de usuario

IBM

IBM TotalStorage DS300 Manual de usuario

IBM

IBM 8271 F12 Manual de usuario

IBM

IBM 16/4 Token Ring PCI Special NIC Instrucciones de uso

IBM

IBM AS/400 Instrucciones de uso

IBM

IBM ioMemory VSL 3.2.6 Manual

IBM

IBM TotalStorage DS300 Manual de usuario

IBM

IBM 39Y9314 Manual

IBM

IBM System storage DS6000 Series Manual técnico

IBM

IBM J56S Manual de usuario

IBM

IBM 8852 - BladeCenter H Rack-mountable Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario