I3 International I3F416U Manual de usuario

i3F416U (with UTP Balun)

Wide Dynamic Range Dome User Guide

CONTENTS

PRECAUTIONS

NOTES OF USE

CEILING MOUNT I

NSTALLATION

WALL MOUNT I

NSTALLATION

OSD MENU

OSD SETTINGS

SPECIFICATIONS

WARNING:

Before attempting to connect or operate this product, read these instructions carefully.

Save this manual for future use.

To avoid electrical shock and to preserve the product warranty, DO NOT disassemble the camera.

Refer servicing to qualified personnel only.

PRECAUTIONS

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications.

Operation of this equipment in a residential area is likely to cause

harmful interference, in which case users will be required to correct the

interference at their own expense.

FCC Caution:

To ensure continued compliance, use only shielded interface cables

when connecting to computer or peripheral devices. Any changes

or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

The serial number of this product may be found on top of the unit. It is

recommended that you note the serial number of this unit in the space

provided and retain this book as a permanent record of your purchase to

aid identication in the event of theft.

Model No.

Serial No.

Date of Purchase:

Features

• Rugged, Vandal-resistant, IP67

•Wide dynamic range color camera with auto iris, 2.8-10mm varifocal

lens

•Available with wide dynamic range(WDR) technology

(102dB typical / 120dB max)

•1/3” Pixim Orca sensor

•Noise ratio > 50dB

•Available with lowlight DSS (digital slow shutter) technology

•WDR model include both composite and unshielded Twisted pair

(UTP) output and progressive scan

•Gamma correction

•AGC

•Slow shutter up to 32x

•Power supply: 12VDC / 24VAC

•Ceiling mount or wall mount

Troubleshooting

The following conditions may be observed when using this camera.

These are inherent in the design and do not stem from any fault in the

camera itself.

• Vertical smear This phenomenon occurs when viewing a very

bright object.

• Patterned noise

This is a xed pattern, which may appear over the

entire monitor screen when the camera is operated

at a high temperature or in a low-light environment.

• Jagged picture When viewing stripes, straight lines, or similar pat-

terns, the image on the screen may appear jagged.

NOTES OF USE

Power Supply

You can use either AC 24V or DC 12V power input. The camera auto-

matically detects the power. When connecting the transformer, be sure

to connect each lead to the appropriate terminal. Incorrect connection

may cause malfunction and/or damage to the video camera.

Operating or storage location

Avoid shooting very bright objects (such as light ttings) for an extended

period. Avoid operating or storing the unit in the following locations:

• Extremely hot or cold places (operating temperature: -10oC to +50oC)

•Close to sources of strong magnetism

• Close to sources of powerful electromagnetic radiation, such as

radios or TV transmitters

•Close to humid or excessively dusty places

•Where exposed to mechanical vibrations

• Close to uorescent lamps or objects reecting light

• Under unstable light sources (may cause ickering)

Attaching the dome casing

Attach the dome casing with the screw provided.

Transportation

When transporting the camera, repack it as originally packed at the

factory, or in materials equal in quality.

Cleaning

• For maximum optical clarity, the dome cover must remain clean. Use

a soft, dry cloth to remove nger prints or dust from the dome cover.

•Use a blower to remove dust from the lens.

•Clean the body with a soft, dry cloth. If it is very dirty, use a cloth

dampened with a small quantity of neutral detergent, then wipe dry.

•Do not use volatile solvents such as alcohol, benzene, or thinners,

as they may damage the surface nishes.

Ensuring Water Resistance

Wrap the connections (threads) between pipes with waterproof adhesive/tape to

prevent water/moisture from entering.

NOTES OF USE

Using the Camera Outdoors

To prevent moisture from getting inside the casing, use sealant (e.g., silicon

sealant) to seal the following areas:

• The holes under the unit casing that is attached to a ceiling or wall.

• Conduit holes on the side and bottom of the unit casing. You can seal these

using a water-proof accessory.

• Joint surface of the camera casing gasket and unit casing.

Location and Function of Parts

1. Unit casing

The unit casing is made of die-cast aluminum and has conduit holes on

the side and bottom.

2. Safety cord

The safety cord prevents the dome casing from falling. To avoid personal

injury and liability, do not remove the safety cord from the unit. If it is

necessary to remove the cord, remember to fasten the screws provided.

3. Zoom & Focus lever

Adjusts the camera range and focus. The lever itself is a screw and can be

removed. Turning this screw completely clockwise locks the position.

4. UTP-Unshield Twisted Pair (white/black wire)

Twisted Pair (TP) terminal (CAT.5E) for video signal. Usage of TP output

requires a TP receiver at the other end of the TP line.

5. Power connector (red/black wire)

Connects to the external power source. (DC12V/AC24V)

6. BNC connector

Connects to the VIDEO IN connector of the Monitor Video Connector

7. Multi-Function switch

Press the multi-function switch for 2 or more seconds and the OSD setup

menu will display on the monitor. Use the multi-function switch to select

desired item and change the settings of the selected item.

8. Monitor (MONITOR OUT) connector

You can connect to an external monitor from this connector. This will allow

you to adjust the camera while looking at the image on the monitor. After

adjusting the camera, disconnect the cable.

456

NOTES OF USE

CEILING MOUNT INSTALLATION

Step 2:

Install the camera onto the ceiling

and fasten securely using the

screws provided.

Step 3:

Remove the mask. Rotate the

main bracket to adjust the pan

angle.

Step 1:

Adhere the guide pattern to the

installation surface. Drill one big

and three small holes, using the

template as a guide.

CEILING MOUNT INSTALLATION

Step 4:

Loosen the screw on the main

bracket, adjust the tilt angle, then

tighten the screw to maintain

setting.

Step 5:

Adjust the camera zoom to a

suitable position.

Step 6: Return mask to

its original position on the

camera. Screw the top cover

to the camera securely.

WALL MOUNT INSTALLATION

Step 2:

Fasten the bottom casing to the

wall by securely tightening the

four screws provided.

Step 3:

Install the camera onto the

bottom casing and secure tightly

with screws.

Step 1:

Adhere the guide pattern to the

installation surface. Drill four

small holes for the plastic drywall

anchors.

Tabla de contenidos

Otros manuales de Cámara de seguridad de i3 International

i3 International

i3 International Ax63Z Series Manual de usuario

i3 International

i3 International Ax73RM-series Manual de usuario

i3 International

i3 International Ax47R4 Manual de usuario

i3 International

i3 International Am52R Manual de usuario

i3 International

i3 International C-Di210 Manual de usuario

i3 International

i3 International Ax40W2 series Manual de usuario

i3 International

i3 International Ax47R series Manual de usuario

i3 International

i3 International Ax83C Manual de usuario

i3 International

i3 International Ax65W Manual de usuario

i3 International

i3 International C-AX401D1M Manual de usuario

i3 International

i3 International Ax46 Series Manual de usuario

i3 International

i3 International Ax68R Manual de usuario

i3 International

i3 International Ax85 Manual de usuario

i3 International

i3 International Ax47R series Manual de usuario

i3 International

i3 International Am57 Manual de usuario

i3 International

i3 International AM42R Manual de usuario

i3 International

i3 International Ax45RM series Manual de usuario

i3 International

i3 International Di721 Manual de usuario

i3 International

i3 International Ax78R Manual de usuario

i3 International

i3 International Di721 Manual de usuario

i3 International

i3 International Ax47R series Manual de usuario

i3 International

i3 International i3F417U Manual de usuario

i3 International

i3 International Ax46DC Manual de usuario

i3 International

i3 International Ax40W2 series Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

i3 International i3F416U Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas