Hypertherm Powermax45 XP Manual de referencia

Field Service Bulletin

Bulletin de service sur le terrain

809520 | Revision 1 | December 2016

| Révision 1 | Decembre 2016

Powermax45 XP®Raw Arc Voltage Kit

Kit de tension d’arc brute Powermax45 XP

Hypertherm Inc.

Etna Road, P.O. Box 5010

Hanover, NH 03755 USA

603-643-3441 Tel (Main Office)

603-643-5352 Fax (All Departments)

[email protected] (Main Office Email)

800-643-9878 Tel (Technical Service)

[email protected] (Technical Service Email)

800-737-2978 Tel (Customer Service)

customer.service@hypertherm.com (Customer Service Email)

866-643-7711 Tel (Return Materials Authorization)

877-371-2876 Fax (Return Materials Authorization)

[email protected] (RMA email)

Hypertherm México, S.A. de C.V.

Avenida Toluca No. 444, Anexo 1,

Colonia Olivar de los Padres

Delegación Álvaro Obregón

México, D.F. C.P. 01780

52 55 5681 8109 Tel

52 55 5683 2127 Fax

Soporte.Tecnico@hypertherm.com (Technical Service Email)

Hypertherm Plasmatechnik GmbH

Sophie-Scholl-Platz 5

63452 Hanau

Germany

00 800 33 24 97 37 Tel

00 800 49 73 73 29 Fax

31 (0) 165 596900 Tel (Technical Service)

00 800 4973 7843 Tel (Technical Service)

[email protected] (Technical Service Email)

Hypertherm (Singapore) Pte Ltd.

82 Genting Lane

Media Centre

Annexe Block #A01-01

Singapore 349567, Republic of Singapore

65 6841 2489 Tel

65 6841 2490 Fax

[email protected] (Marketing Email)

TechSupportAP[email protected] (Technical Service Email)

Hypertherm Japan Ltd.

Level 9, Edobori Center Building

2-1-1 Edobori, Nishi-ku

Osaka 550-0002 Japan

81 6 6225 1183 Tel

81 6 6225 1184 Fax

HTJapan.info@hypertherm.com (Main Office Email)

TechSupportAP[email protected] (Technical Service Email)

Hypertherm Europe B.V.

Vaartveld 9, 4704 SE

Roosendaal, Nederland

31 165 596907 Tel

31 165 596901 Fax

31 165 596908 Tel (Marketing)

31 (0) 165 596900 Tel (Technical Service)

00 800 4973 7843 Tel (Technical Service)

[email protected]

(Technical Service Email)

Hypertherm (Shanghai) Trading Co., Ltd.

B301, 495 ShangZhong Road

Shanghai, 200231

PR China

86-21-80231122 Tel

86-21-80231120 Fax

86-21-80231128 Tel (Technical Service)

[email protected]

(Technical Service Email)

South America & Central America: Hypertherm Brasil Ltda.

Rua Bras Cubas, 231 – Jardim Maia

Guarulhos, SP – Brasil

CEP 07115-030

55 11 2409 2636 Tel

[email protected] (Technical Service Email)

Hypertherm Korea Branch

#3904. APEC-ro 17. Heaundae-gu. Busan.

Korea 48060

82 (0)51 747 0358 Tel

82 (0)51 701 0358 Fax

[email protected] (Marketing Email)

TechSupportAP[email protected]

(Technical Service Email)

Hypertherm Pty Limited

GPO Box 4836

Sydney NSW 2001, Australia

61 (0) 437 606 995 Tel

61 7 3219 9010 Fax

[email protected] (Main Office Email)

TechSupportAP[email protected]

(Technical Service Email)

Hypertherm (India) Thermal Cutting Pvt. Ltd

A-18 / B-1 Extension,

Mohan Co-Operative Industrial Estate,

Mathura Road, New Delhi 110044, India

91-11-40521201/ 2/ 3 Tel

91-11 40521204 Fax

HTIndia.info@hypertherm.com (Main Office Email)

TechSupportAP[email protected]

(Technical Service Email)

1/28/16

Powermax and Hypertherm are trademarks of Hypertherm Inc. and may be registered in the United States and/or other countries. All other trademarks

are the property of their respective holders.

One of Hypertherm’s long-standing core values is a focus on minimizing our impact on the environment. Doing so is critical to our, and our customers’,

success. We are always striving to become better environmental stewards; it is a process we care deeply about.

Powermax et Hypertherm sont des marques d’Hypertherm Inc. qui peuvent être déposées aux États-Unis et/ou dans d’autres pays. Toutes les autres

marques de commerce sont la propriété de leurs détenteurs respectifs.

Une des valeurs fondamentales d’Hypertherm depuis toujours est l’accent mis sur la minimisation de notre impact sur l’environnement. Cet objectif est

essentiel pour notre réussite et celle de nos clients. Nous nous efforçons de devenir de meilleurs gestionnaires environnementaux, c’est une chose qui

nous tient à cœur.

Raw Arc Voltage Kit

Powermax45 XP Field Service Bulletin 809520 3

Introduction

Purpose

This field service bulletin explains how to install a customer-supplied machine interface cable that

does not use the internal 50:1 voltage divider on the Powermax45 XP.

Notice: Installation of the system at the installed site is subject to the approval of the Local

Inspection Authorities (LIA). Without approval of the LIA, modification of the factory installed

wiring voids the safety test marks (for example, cCSAus, CCC, CE, GOST-TR, UkrSEPRO,

RCM, EAC) applied to the product in the Hypertherm factory, and the safety certificates

provided by Hypertherm become invalid after modification.

Tools and materials needed

Wire strippers

Wire terminal crimper

Assorted Phillips®and TORX®screwdrivers

Electric drill with a 15 mm or 19/32 inch drill bit

0.75 mm2or 18 AWG, 2 wire, non-shielded cable similar to

OLFLEX®190 (manufacturer’s part number 601802)

M3 (#5) insulated ring terminals, quantity 2

428689 Kit contents

WARNING

ELECTRIC SHOCK CAN KILL

Disconnect electrical power before performing any maintenance.

All work requiring removal of the power supply cover must be performed

by a qualified technician.

See the safety information provided with your product for more safety

precautions.

Part number Description Quantity

008279 Strain relief 1

075529 M3 x 10 mm machine screw with lock washer 2

Raw Arc Voltage Kit

4809520 Field Service Bulletin Powermax45 XP

Install the interface cable

Connecting a cable to the power board to bypass the voltage divider board and access raw arc

voltage must be done by trained service personnel.

Remove cover and component barrier

1. Turn OFF the power. Disconnect the power cord and gas supply.

2. Remove the two screws from the power supply handle . Remove the two screws from the

bottom of the front and rear panels. Tilt the tops of the front and rear panels away from the

unit to pull the handle out .

WARNING

SHOCK HAZARD, ENERGY HAZARD, AND FIRE HAZARD

Connecting directly to the plasma circuit for access to raw arc voltage

increases the risk of shock hazard, energy hazard, and fire hazard in the

event of a single fault. The output voltage and the output current of the

circuit are specified on the data plate.

Raw Arc Voltage Kit

Powermax45 XP Field Service Bulletin 809520 5

3. Slide the cover off.

4. Remove the two plastic pins that secure the component barrier to the main power board. Slide

the component barrier off.

Raw Arc Voltage Kit

6809520 Field Service Bulletin Powermax45 XP

Prepare the interface cable

1. Use 2 conductor, non-shielded 18 AWG wires to connect to the power supply. Measure the

distance needed to connect from the CNC to the power supply. Add an additional 51.5 cm

(20.25 inches) to make the connection inside the power supply.

2. Cut back the outer jacket 48.3 cm (19 inches) from one end of the cable. Make sure you do not

cut into the insulation on the two 18 AWG wires.

Do not strip the wire ends until after they have been routed through the

power supply.

Install the strain relief

1. Pull the rear panel slightly away from the unit leaving enough space to drill a hole while avoiding

any contact with internal components or wires when drilling.

2. Use a 15 mm (19/32 inch) drill to drill out the interface cable entry point on the panel. Clean the

area of any chips from drilling.

48.3 cm (19 inches)

Raw Arc Voltage Kit

Powermax45 XP Field Service Bulletin 809520 7

3. Attach the strain relief (008279) and tighten the inner nut to secure it to the panel. Attach the

outer retention nut but do not tighten.

Connect the interface cable

1. Pass the cable through the strain relief. The outer jacket should slightly protrude through the

back of the strain relief. Make sure the wire length is 48.3 cm (19 inches) inside the power

supply.

2. Tighten the outer retention nut on the strain relief. Make sure the strain relief closes on the

outer jacket of the cable and holds it securely in place.

3. Insert the interface cable wires through the pass-through holes used by the transformer to

reach the other side of the unit.

Different power supply configurations will have the transformer wires

routed differently. Use the pass-through holes that are not utilized by the

transformer.

Raw Arc Voltage Kit

8809520 Field Service Bulletin Powermax45 XP

4. Route the wires to bring the ends to the (-) and (+) threaded inserts on the main circuit board.

5. Strip the insulation 1.27 mm (0.5 inches) from the ends of the wires.

6. Crimp an M3 insulated terminal ring connector on the end of each wire. Make sure there are no

loose wire strands.

7. Connect the positive lead to the (+) threaded insert (J22) on the power supply board. Use one

of the screws included in the kit (075529). Tighten the screw to 23.0 kg∙cm (20 inch·pounds).

Make sure the wire runs downward and the insulated part of the ring terminal is off the board.

8. Connect the negative lead to the (-) threaded insert (J9) on the power supply board. Use one of

the screws included in the kit (075529). Tighten the screw to 23.0 kg∙cm (20 inch-pounds).

Make sure the wire runs downward and the insulated part of the ring terminal is off the board.

9. Make sure to mark on the other end of the cable which wire is positive (+) and which is

negative (-).

10. Replace the component barrier and secure it to the main circuit board with the two plastic pins.

11 . Set the front and rear panels back in place.

( + )

( - )

(-) (+)

( + )

( - )

( + )

( - )

( + )

( - )

Raw Arc Voltage Kit

Powermax45 XP Field Service Bulletin 809520 9

12. Make sure the ground clip is connected to the ground wire. The clip should be set in place to

accept the screw from the handle.

13. Slide the cover back on.

14. Tilt the front and rear panels to reattach the handle.

15. Secure the front and rear panel bottom screws.

16. Secure the front and rear panel top screws.

17. Connect the other end of the cable to the equipment according to the manufacturer’s

instructions. Remember to observe polarity.

Notice: The output of the internal voltage divider board is designed to prevent shock, energy

and fire hazards, and is intended to satisfy most codes and standards for external wiring outside

the electrical enclosure. All external wiring practices for an unprotected raw arc voltage

should be reviewed and approved by the Local Inspection Authorities (LIA) at the

time of installation prior to operation and use.

Raw arc voltage wiring terminals and connections should not be exposed to accidental

contact under normal and single fault conditions.

External wiring from an unprotected (that is, no voltage divider used in the power source)

raw arc voltage routed inside conduit between electrical enclosures will normally satisfy all

electrical codes and standards worldwide. Failure to address the hazards associated

with live contact, accessibility and single fault failures to this unprotected output

can result in death or fire.

Raw Arc Voltage Kit

10 809520 Field Service Bulletin Powermax45 XP

A voltage divider board inside the CNC protects only the CNC and does NOT protect the

external interconnecting wiring between the power source and the CNC. Over-current

protection may be required to protect the user and/or machine in fault conditions.

External wiring outside the electrical enclosure should be suitable for the installation and meet

national and local regulations (for example, NFPA 70 NEC, NFPA 79, Canadian Electrical Code,

CSA/CAN E60974-1, IEC 60204-1, BS 7671) or other codes and/or standards applicable to

the installed site where the equipment will be operated.

Otros manuales para Powermax45 XP

Tabla de contenidos

Idiomas:

Otros manuales de Sistema de soldadura de Hypertherm

Hypertherm

Hypertherm HPR130 Manual de usuario

Hypertherm

Hypertherm T45v Manual de referencia

Hypertherm

Hypertherm powermax1000 Manual de usuario

Hypertherm

Hypertherm HyDefinition HD4070 Hoja de instrucciones

Hypertherm

Hypertherm Powermax105 Manual de usuario

Hypertherm

Hypertherm Powermax 30 Manual de usuario

Hypertherm

Hypertherm powermax65 Manual de referencia

Hypertherm

Hypertherm Powermax30 AIR Manual de usuario

Hypertherm

Hypertherm MAX200 Hoja de instrucciones

Hypertherm

Hypertherm HPRXD Series Guía

Hypertherm

Hypertherm powermax1000 Manual de usuario

Hypertherm

Hypertherm Powermax 125 Manual de usuario

Hypertherm

Hypertherm powermax600 Manual de usuario

Hypertherm

Hypertherm Powermax 85 Manual de usuario

Hypertherm

Hypertherm HT2000 Manual de usuario

Hypertherm

Hypertherm HT4400 Hoja de especificaciones

Hypertherm

Hypertherm Powermax45 XP Manual de usuario

Hypertherm

Hypertherm HyDefinition HD3070 Manual de usuario

Hypertherm

Hypertherm Powermax 1000 Manual de referencia

Hypertherm

Hypertherm XPR300 Manual de usuario

Hypertherm

Hypertherm Powermax45 XP Manual de referencia

Hypertherm

Hypertherm powermax65 Manual de referencia

Hypertherm

Hypertherm powermax65 Manual de usuario

Hypertherm

Hypertherm Powermax30 AIR Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

Miller

Miller Big Blue 400D Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manual de usuario