HunterDouglas Duette Honeycomb Shades Manual de usuario
Installation
•
Care
Duette
®
Honeycomb Shades
LightLock
™
System for LiteRise
®
and
PowerView
®
Automation Operating Systems
CONTENTS
© 2020 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or
their respective owners.
GETTING STARTED
LightLock™Parts.............................................................................1
Tools and Fasteners Needed ..........................................................2
INSTALLATION
Install the Channels........................................................................3
Install the Brackets.........................................................................7
Apply D-seal (If Necessary) ............................................................7
Install the Shade.............................................................................8
Test the Shade................................................................................8
Finish the Installation .....................................................................8
CARE
Removing the Shade (If Necessary) .............................................11
Removing the Bottom and Rear Channels (If Necessary) ............11
WARRANTY ......................................................................... 13
Questions?
Call Hunter Douglas Consumer Support at 1-888-501-8364.
GETTING STARTED
1
Front Channel
Bottom Channel
Pre-drilled
Mounting Channel
Top End Cap
Bottom End Cap
Rear Channel Template
Room Side
Duette®LightLock™Template
3”
Flush Mount
Depth (2
1
/
2
"):
- LiteRise
©2020 Hunter Douglas. All rights reserved.
Alltrademarks used herein are the property of
HunterDouglas or their respective owners.
Flush Mount
Depth (3
3
/
4
"):
- PowerView
(Headrail-mounted
rechargeable
battery wand)
Flush Mount
Depth (3"):
- PowerView
(Batterywand —
high and low mount)
Trim the template at this dotted line for: PowerView®
(High and low mount battery wand)
Trim the template at this dotted line for: LiteRise®
5109604505 Rev. 10/20
QTY: 1
Mounting Channel (Mount to Window Jamb)
Street Side
Room Side
Rear Channel
(Snap into
Mounting Channel)
Channel Assembly (Top View)
Window Jamb
Front Channel
(Snap into Rear Channel)
Bottom
Channel
LightLock™Parts
2
GETTING STARTED
Thank you for purchasing Hunter Douglas Duette®Honeycomb Shades. With proper
installation, operation, and care, your new shades will provide years of beauty and
performance.
Please thoroughly review this instruction booklet and the enclosed packing list before
beginning the installation.
Tools and Fasteners Needed
■ 1" metal putty knife
■
1
⁄
4
" hex and Flat blade screwdrivers
■ Level (laser level is recommended)
■ Mallet
■ Measuring tape and pencil
■ Power drill,
3
⁄
32
" drill bit and
1
⁄
4
" hex driver
■ Scissors
In addition, you will need fasteners designed to work with your specific mounting surface(s).
■ #6 Hex Head Screws (Provided). 1
1
⁄
2
" screw is provided per installation bracket. Also,
1
1
⁄
2
" screws are provided for the mounting channels — the number of the screws provided
depends on the length of the channels.
Mounting Type and Window Terminology
If the mounting channels and installation brackets are mounted correctly, the rest of the
installation process follows easily. To prepare for these important steps, review the basic
window terminology illustrated below. Note that the LightLock™system is only available for
inside mount.
#6 x 1
1
∕
2
"
Hex Head Screw
(Provided)
Longer #6 Hex Head Screw
for Use with Spacer Blocks
(Not Provided)
#6 Flat Head Screw
for Use with End Mounts
(Provided)
Speed Nut
and Screw
(Two Provided with
Each Extension Bracket)
Inside Mount
Shade fits within
window opening.
Collectively, the sill and
jambs are called the
“window casement.”
Molding
Head Jamb
Sill
Jamb Jamb
INSTALLATION
3
Install the Channels
■ Using the outline on the template, determine where to mount the side channel.
➤ If your shade is LiteRise®or PowerView®(battery wand), the minimum mounting depth
for flush mount is 2
1
⁄
2
". Trim the template at the dotted line prior to use.
➤ If your shade is PowerView (battery wand — high and low mount), the minimum
mounting depth for flush mount is 3".
➤ If your shade is PowerView (rechargeable battery wand), the fully recessed minimum
mounting depth is 3
3
⁄
4
" and the minimum casement depth is 1
1
⁄
4
".
■ Place the template at the bottom of the left side jamb
and mark the rear edge of the template on the jamb.
➤ This mark represents the rear edge of the mounting
channel.
■ Repeat this step for the top of the left jamb.
■ Repeat the above steps for the right jamb.
■ Using the template, mark the location for the installation brackets on the head jamb.
➤ Place the template in the top left corner of the window opening.
➤ Line up the back edge of the template with the mark
previously made on the side jamb.
➤ Mark the center hole, if depth permits.
➤ Repeat for the right side.
➤ If more than two installation brackets came with your
order, space additional bracket(s) evenly between the
two end brackets and mark their location.
INSTALLATION
4
■ Test fit the left pre-drilled mounting channel into the window opening.
➤ If the gap is greater than
1
⁄
16
", select the proper combination of top and bottom end
caps to minimize the gap.
NOTE: D-seal on the top of the top end caps can be effective in reducing light gaps.
➤ Attach the end caps as shown and test to ensure a snug fit.
■ Repeat for the right side.
Gap
Street
Pre-drilled
holes
Room
Top Left Bottom Left
Pre-drilled
holes are
6in apart
INSTALLATION
5
■ Place the mounting channel in the window opening, lining up the rear of the mounting
channel to the marks previously made on the side jambs.
■ Attach the mounting channel to the window frame at the
pre-drilled holes using the screws provided.
NOTE: For highly nonconforming flat surfaces or
out of square installs, it may be necessary to add
an additional screw in the not pre-drilled location
of the mounting channel for additional support.
Screws in the U channel should be placed a
maximum of 18" apart.
■ Repeat for the opposite side.
X
Optional hole location.
Maximum 18in apart
For nonconforming flat or
out of square installs.
INSTALLATION
6
■ Remove the protective liner from the front and the rear channels.
■ Snap the rear channel onto the mounting channel, starting at the bottom and working up
to the top. Use a mallet if necessary.
■ Reach behind the rear
channel and make
sure there is
no gap between the
rear channel and the
mounting
channel.
■ Repeat for the opposite side.
INSTALLATION
7
Install the Brackets
■ Your order will include the correct number of installation brackets for your shade width, as
shown in the table.
■ Install the installation brackets.
➤ Drill the screw holes already marked on the head jamb using a
3
⁄
32
" drill bit.
■ Use a level to check that the mounting surface is level. Shim the brackets if necessary.
■ Attach the installation brackets using the screws
provided.
IMPORTANT: The back edges of the installation
brackets should line up with the back of the rear
channel. If the brackets are closer to the window,
move them forward.
IMPORTANT: The front edges of the installation
brackets must be level and aligned. If mounting to a
heavily textured surface, shim the brackets, if needed.
Apply D-seal (If Necessary)
■ We have provided an adhesive-backed D-seal to reduce
any light gaps created by uneven surfaces. Install the
D-seal on the headrail, as necessary, to eliminate the
light gaps.
Shade
Width
Brackets
Required
12" – 36" 2
36
1
∕
8
" – 72" 3
72
1
∕
8
" – 108" 4
108
1
∕
8
" – 144" 5
144
1
∕
8
" – 174" 6
Installation
Bracket
End Mount
Brackets
INSTALLATION
8
Install the Shade
■ Refer to the appropriate page based on your order.
➤ For LiteRise®shades: see the Duette Honeycomb Shades LiteRise Installation,
Operation, and Care document.
➤ For PowerView®shades: see the Duette Honeycomb Shades PowerView Automation
Installation, Operation, and Care document.
Test the Shade
■ Test the operation. The shade should be evenly spaced from both rear channels and
operate smoothly.
➤ For LiteRise shades: use the handle to lower/raise the shade. Refer to the Duette
Honeycomb Shades LiteRise Installation, Operation, and Care document.
➤ For PowerView shades: use the control button to test the operation. Refer to the
Duette Honeycomb Shades PowerView Automation Installation, Operation, and Care
document.
NOTE: If the channels interferes with the shade’s operation, make sure the side channel is
installed completely to the mounting channel.
Finish the Installation
Install Bottom Channel
■ Clean the sill using standard household cleaners.
■ Test fit the bottom channel.
➤ Trim the channel, if needed.
■ Remove the protective liner from the bottom channel.
IMPORTANT: Be sure that the bottom channel cover is placed on the street side.
Bottom Channel
Bottom
Channel
Cover
Room Side
Street Side
Tabla de contenidos
Otros manuales de Persiana de ventana de HunterDouglas
HunterDouglas
HunterDouglas Solera EasyRise Manual de lista de piezas
HunterDouglas
HunterDouglas 2" Horizontal Aluminum Blinds Manual de lista de piezas
HunterDouglas
HunterDouglas PowerView Gen 3 Manual de usuario
HunterDouglas
HunterDouglas Luminette PowerView Instrucciones de montaje
HunterDouglas
HunterDouglas Silhouette Nantucket PowerView Gen 3... Manual de lista de piezas
HunterDouglas
HunterDouglas Vignette Modern Roman Shades Manual de lista de piezas
HunterDouglas
HunterDouglas Decor Standard Cordlock Manual del propietario
HunterDouglas
HunterDouglas PowerView M40T Manual de usuario
HunterDouglas
HunterDouglas RB 500 Guía de seguridad
HunterDouglas
HunterDouglas RB 500 Manual de usuario
HunterDouglas
HunterDouglas Paramount Manual del propietario
HunterDouglas
HunterDouglas VS 100 Guide rail Guía de mantenimiento y servicio
HunterDouglas
HunterDouglas Cadence Soft Vertical Blinds Manual de lista de piezas
HunterDouglas
HunterDouglas Palmetto Horizontal Shadings Manual
HunterDouglas
HunterDouglas Specialty Motorized Vertical Blinds Manual de lista de piezas
HunterDouglas
HunterDouglas WOODMATES Manual de usuario
HunterDouglas
HunterDouglas SCG 64 Manual de usuario
HunterDouglas
HunterDouglas 5-216 Manual de usuario
HunterDouglas
HunterDouglas EverWood Guía del usuario
HunterDouglas
HunterDouglas 5-151 Manual de usuario
Manuales populares de Persiana de ventana de otras marcas
Domondo
Domondo PureNight Manual de instrucciones de instalación
rollease acmeda
rollease acmeda Easy Spring Air Guía de configuración
IKEA
IKEA KADRILJ Manual de usuario
Hallis Hudson
Hallis Hudson Rolls Super glide Manual de usuario
Benthin
Benthin P1614 Manual de usuario
MV LINE
MV LINE CLARA 015 Manual de instrucciones
