HunterDouglas Country Woods Manual de operación

Installation and

Care Instructions

Fixed Slat

Specialty Shapes

Country Woods®

Wood Blinds

HEXAGON OCTAGON CIRCLE OVAL

ARCH

QUARTER

ARCH ANGLE TRIANGLE

Tools needed for installing your blind:

• Measuring tape

• Pencil

• Flat blade screwdriver

• Phillips screwdriver

• Carpenter’s level

• Power drill, drill bits and 1/4" hex

bit socket (or socket wrench with

1/4" hex socket)

In addition, you will need fasteners designed to work with your

specific mounting surfaces:

THANK YOU

for purchasing a Hunter Douglas product. Your

new blind has been custom built for you from the highest quality

materials to provide you with a lifetime of beauty and function.

Important: Read these instructions all the way through before

beginning.

Getting Started

Remove the blind from the package. Keep the packaging until the

blind is installed to your satisfaction.

Each fixed slat specialty shape you ordered includes:

• The required number of slats, cut to varying widths to form the

correct shape.

• Two or more uprights into which the slats are inserted.

•Arch, quarter arch, angle, and triangle only: One bottom rail to

which the uprights are attached, along with two flat head screws

(#6 x 11/4") per upright to attach the uprights to the bottom rail;

and one extra 2" slat for light control.

Each fixed slat specialty shape you ordered also includes all necessary

mounting hardware:

• The required number of mounting brackets. There are two types

of brackets, one for inside mounts and one for outside mounts.

• Two #6 x 11/4" hex head screws per mounting bracket.

• One snap button per mounting bracket.

BOTTOM RAIL

(Arches, Quarter Arches, An

les, Trian

les onl

)

MOUNTING BRACKET

(Inside Mount) MOUNTING

BRACKET

(Outside Mount)

SNAP

BUTTON

UPRIGHT

SLATS

Wood

Drywall, Plaster

Metal

Mounting Surface Fastener

No. 6 Hex Head Screws

(Provided)

Wall Anchors, Expansion Bolts

(Not Provided)

Sheet Metal Screws

(Not Provided)

For assistance, call the Hunter Douglas

Customer Information Center

at 1-888-501-8364

7:00 AM to 4:30 PM MST, Mon.-Fri.

Visit our Web site at hunterdouglas.com

Assemble the Blind

Blinds with No Bottom Rail

Hexagon, Octagon, Circle, and Oval

Arrange the Uprights

Each upright is marked with a label: A, B, C, etc. Start on the left side

with “A” and arrange the uprights as labeled.

• Stand the uprights on their back edge so that the slots are face up,

with the slots angled the same on all uprights.

• Arrange the uprights so that they approximate the shape of the

blind, with the slots aligned horizontally.

• The distance between uprights should be approximately equal.

Install the Slats

• Slats are stacked in the order of assembly.

• Start at the bottom slot of the uprights and insert the first slat.

• Work your way up to the top until all slots are filled.

A B C D E

SHAPE OF

BLIND

Blinds with Bottom Rail

Arch, Quarter Arch, Angle, and Triangle

Position the Bottom Rail

• Stand the bottom rail on its back edge, with its front edge facing

up and the countersunk holes toward you.

• Labels indicating the position of the uprights are located on the

top of the bottom rail, near the front edge.

Arrange the Uprights

• Each upright is marked with a label that matches the label on the

bottom rail.

• Arrange the uprights as labeled against the top side of the bottom

rail.

• The slots in the uprights must face up, and the end of the upright

with two holes goes against the bottom rail.

B C

COUNTERSUNK

HOLES

UPRIGHT POSITION LABELS

UPRIGHT

POSITIONS

BOTTOM RAIL

BOTTOM

SIDE

TOP

SIDE

FRONT EDGE

BACK EDGE

Attach the Uprights to the Bottom Rail

• Attach the uprights to the bottom rail using two flat head screws

(#6 x 11/4") per upright.

• The screws go through the countersunk holes in the bottom rail,

and then into the uprights.

Double check that the slots in all the uprights are facing up.

Important: Do not overtighten the screws.

Install the Slats

• Insert the slats into the slots in the uprights. Start at the bottom

and insert the longest slat.

• Work your way up to the top until all slots are filled.

A B C D E F G

SHAPE OF

BLIND

Important: With 25/8" slats, the bevel on the bottom part of the slat

should face downward (see illustration at right).

Slat

Bevel

Upright

Important: With 25/8" slats, the bevel

on the bottom part of the slat should

face downward.

Optional Additional Slat Instllation

Arch, Quarter Arch, Angle, and Triangle

An additional slat labeled “extra” is included with your order. This

slat is the same length as the bottom rail. It is designed to help

eliminate the light gap at the bottom of the specialty shape.

If you choose to install this extra slat:

• Use the Velcro provided to attach the slat to the rear side of the

bottom rail, with the slat upright as shown in the illustrations.

• Be sure the slat is installed on the rear side of the bottom rail so

that it faces the window when the blind is installed.

2Install the Blind

Snap Buttons

• Snap buttons are installed onto the top of the uprights.

• On blinds with no bottom rail, snap buttons are installed onto the

bottom of the uprights, as well.

• On outside mounted blinds with a bottom rail, snap buttons are

also installed onto the ends of the rail.

The following chart shows onto which uprights you will need to

install snap buttons. The black boxes indicate snap button locations.

NUMBER OF UPRIGHTS

= Snap Button Locations

UPRIGHT LABEL DESIGNATIONS

ACEG

BCD

BCDE

BDF

Front View

Rear View

Extra

Slat

Extra

Slat

SNAP

BUTTON

UPRIGHT

Notice on the chart that:

• A blind with two uprights will have snap buttons installed onto

both.

• Blinds with three to six uprights will have snap buttons installed

onto the middle upright(s), omitting only the two on the far left

and far right.

• Blinds with seven uprights will have snap buttons installed onto

alternate uprights.

Install the Snap Buttons

• Insert snap buttons into the

pre-drilled holes on the uprights

indicated on the chart, and

press them firmly in place.

• On blinds with no bottom

rail, remember to install

snap buttons on both the

top and bottom of the

uprights.

• On outside mounted blinds

with a bottom rail, also install

snap buttons into the pre-drilled

holes on the ends of the rail.

Install the Mounting Brackets

Mark the Mounting Bracket Locations

• With inside mounted specialty shapes, hold the blind inside the

opening, flush with the front of the opening, and mark on the

casement the locations of the front edges of all snap buttons.

• With outside mounted specialty shapes, center the blind over the

opening and mark the location of all snap buttons on the wall or

molding.

Attach the Mounting Brackets (Inside Mounts)

• Position the circular opening at the front of the brackets

approximately 1/4" behind where you marked the front edge

location of the snap buttons.

• Mark where to drill pilot holes for the #6 x 11/4" mounting screws.

• Drill 1/8" pilot holes and attach the brackets with the screws.

• Be sure all brackets are mounted the same depth inside the

opening.

MARKS

TOP OF

OPENING

Product Code No. 8800031002 1M-9/04

™Trademark of Hunter Douglas Inc. Patented in the U.S. and foreign countries.

U.S. and foreign patents pending.

A NOTE ABOUT WOOD PRODUCTS

Our wood blinds are true wood products, made from 100% hardwood.

There will be variations in color, grain, texture, and warpage that are

characteristic of all woods. These variations will be especially visible

in blinds with light color stains. The variations are normal and natural,

and are considered acceptable quality.

Care and Cleaning

Like any wood furnishings, Country Woods blinds should be cleaned

on a routine basis to keep them looking new.

• Dust regularly. Use a soft clean cloth, chemically-treated dust

cloth or dusting mitt.

• Blinds may also be vacuumed using a brush attachment.

• Another way to clean blinds is simply by wiping them with a soft,

damp cloth.

• Stained blinds, like wood furniture, should be treated periodically

with lemon oil or other wood preservative to protect their finish

and enhance their luster.

Important: Hunter Douglas does not recommend ultrasonic cleaning

of wood blinds.

Install the Blind

• Align the snap buttons on the uprights (and bottom rail, if

applicable) with the front of the mounting brackets.

• Insert the snap buttons into the mounting brackets until they

“snap” in place.

Attach the Mounting Brackets (Outside Mounts)

• Orientation of the mounting brackets depends on whether the

snap button is at the top or bottom of the upright, or the left or

right end of the bottom rail (see illustration).

• Position the brackets on your marks so that the circular opening

at the front of the brackets will fit onto the snap buttons.

• Mark where to drill pilot holes for the #6 x 11/4" mounting screws.

• Drill 1/8" pilot holes and attach the brackets with the screws.

ORIENTATION FOR

BOTTOM OF UPRIGHT

MARK

SNAP

BUTTON

SNAP

BUTTON

INSIDE MOUNT OUTSIDE MOUNT

Otros manuales de Persiana de ventana de HunterDouglas

HunterDouglas

HunterDouglas Silhouette A Deux Manual de lista de piezas

HunterDouglas

HunterDouglas Solera EasyRise Manual de lista de piezas

HunterDouglas

HunterDouglas Duolite Shades Manual de lista de piezas

HunterDouglas

HunterDouglas Alustra Woven Textures ST30 Manual de lista de piezas

HunterDouglas

HunterDouglas Vignette Tiered Manual de usuario

HunterDouglas

HunterDouglas PowerView Gen 3 Manual de usuario

HunterDouglas

HunterDouglas Alustra Woven Textures Manual de usuario

HunterDouglas

HunterDouglas Vignette Modern Roman Shades Manual de lista de piezas

HunterDouglas

HunterDouglas 5-156 Manual de usuario

HunterDouglas

HunterDouglas PowerView EOS Plisse Manual de usuario

HunterDouglas

HunterDouglas Skyline Manual de lista de piezas

HunterDouglas

HunterDouglas Designer Roller Shades Manual de lista de piezas

HunterDouglas

HunterDouglas Standard Cordlock, Moveable Slat Specialty... Guía del usuario

HunterDouglas

HunterDouglas Vignette Modern Roman Shades Manual de lista de piezas

HunterDouglas

HunterDouglas Specialty Motorized Vertical Blinds Manual de lista de piezas

HunterDouglas

HunterDouglas 5-257 Manual de usuario

HunterDouglas

HunterDouglas Cadence Manual de lista de piezas

HunterDouglas

HunterDouglas Duette Honeycomb Shades Manual de usuario

HunterDouglas

HunterDouglas WOODMATES Manual de usuario

HunterDouglas

HunterDouglas LiteRise Manual de usuario

HunterDouglas

HunterDouglas Duette Manual de usuario

HunterDouglas

HunterDouglas Standard Hardware System Manual de lista de piezas

HunterDouglas

HunterDouglas RB 500 Manual de usuario

HunterDouglas

HunterDouglas Paramount Manual del propietario

Manuales populares de Persiana de ventana de otras marcas

Jysk

Jysk ROGEN Manual de usuario

SOMFY

SOMFY 1241752 Manual de usuario

Rollos

Rollos S-Nanorollo V2 Guía de planificación

Teptron

Teptron Move Manual de usuario

Renson

Renson Outdoor Loggia Guía de seguridad

Project Source

Project Source CDLF2342W Manual de usuario

Domondo

Domondo PureNight Manual de instrucciones de instalación

rollease acmeda

rollease acmeda Easy Spring Air Guía de configuración

IKEA

IKEA KADRILJ Manual de usuario

Hallis Hudson

Hallis Hudson Rolls Super glide Manual de usuario

Benthin

Benthin P1614 Manual de usuario

MV LINE

MV LINE CLARA 015 Manual de instrucciones

Current

Current E-WAND Guía

weinor

weinor VertiTex ZipR Manual

Roto

Roto ZAR M R4/R7 Manual de usuario

SOMFY

SOMFY Movelite WT Series Manual de usuario

Acmeda

Acmeda RF400 Series Manual de usuario

Motura

Motura Pli_353/3 Manual de usuario