Huawei SmartLi Series Manual de usuario

Issue: 05

Part Number: 31500BED

Date: 2019-10-15

SmartLi Quick Guide

1Overview

Model Capacity Weight Dimensions (H x W x D) Configuration type

SmartLi-512V-80AH-F 80 Ah < 750

kg 2000 mm x 600 mm x 850

With an LCD

SmartLi-512V-80AH-S Without an LCD

The auxiliary wrench is used to assist in turning on and off the battery switch.

NOTE

Battery circuit breaker

Monitoring module

Battery management module

End pressure gauge

Battery module

Fuse

MDU

Auxiliary

wrench

Fuse

Fire-trace

tube

Fire

cylinder

Front View Rear

View

Riser screw

1. Check the fire cylinder and all components for any damage, abrasion, or corrosion. If there is any

visible abrasion or corrosion, replace the damaged components and all corroded components.

2. Fill the fire cylinder with extinguishant. The recommended extinguishant is heptafluoropropane or

perfluorohexanone.

3. Check the status of the fire cylinder.

•Check that the ball valve is closed (vertical to the cylinder).

•Check that the reading of the pressure gauge on the fire cylinder is greater than 1.6 MPa and

the pointer is in the green zone.

4. Remove the rear panel of the cabinet.

5. Install the fire cylinder.

2Installing a Fire Cylinder

6. Install the fire-trace tube on the fire cylinder.

Do not bend or twist the fire-trace tube or bind the tube using cable ties. Otherwise, the fire cylinder

may fail.

a. Remove the connection nut and riser screw thread from the top of the fire cylinder, and route

the nut and riser screw thread through the fire-trace tube.

Fire-trace tube

Connection nut

1. Before installation, read the user manual carefully to get familiar with product information and

safety precautions.

2. Use insulated tools during installation and operation.

3. Only Huawei engineers or engineers certified by Huawei are allowed to install, commission, and

maintain the battery cabinet. Otherwise, personal injury or equipment damage may occur, and

the resulting battery cabinet faults are beyond the warranty scope of Huawei.

4. This document describes how to install a single battery cabinet. For details about how to install

parallel systems, contact Huawei technical support.

•Keep the fire cylinder upright.

•Ensure that the front of the

pressure gauge faces the

right side of the cabinet (as

shown in the figure) and that

the cylinder does not

interfere with the battery

trays and the rear cover of

the cabinet.

b. Clamp the end of the fire-trace tube to the threaded nozzle using a pipe holder.

Hold the pipe holder close to the end to

avoid bending the tube during pipe

insertion.

c. Tighten the nut to a torque of 7 N·m.

7. Remove the valve positioning kit, open the valve, reinstall the positioning kit, and secure it.

8. Check the end pressure gauge on the front of the cabinet. The pointer should be in the green

zone and the pressure reading should be greater than 1.6 MPa. Record the reading of the

pressure gauge. 8 hours later, observe the pressure gauge again. The pressure reading should

remain unchanged.

3Installing a Cabinet

1. Determine the position for installing the cabinet.

Mark mounting holes based on the drawings

(unit: mm).

5. Open the front door, and remove the four

rubber plugs from the bottom of the

cabinet.

1. Lower the four leveling feet at the bottom of

the cabinet by using a wrench until all the four

castors at the bottom hang in the air and the

leveling feet bear the whole cabinet weight.

2. Check whether the bottom of the cabinet is

horizontal by using a level instrument. If the

cabinet is not leveled, adjust the leveling feet.

2. Use a hammer drill to drill four holes for

installing expansion bolts and then install

four expansion bolts in the holes. Remove

the bolt, spring washer, and flat washer.

3. Slide the cabinet on its castors to the

installation position.

4. (Optional) If the castors of the SmartLi

need to be lifted from the ground, perform

Step 1 to Step 2 in Non-Secured

Installation.

6. Insert four M12x115 expansion bolts into

the expansion bolt holes in the floor, and

tighten the expansion bolts.

Secured Installation

3.1

Non-Secured Installation

3.2

4Cable Connection Reference

•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps may

ignite and cause personal injury or device damage.

•After cables have been installed, clean the cabinets in a timely manner. Keep the cabinets and

surrounding environment clean and tidy.

•You need to prepare terminals onsite. The stripped length of the copper wire should be the

same as that of the part of the terminal that covers the conductor.

The cabling route is for reference only. Connect cables based on site requirements.

NOTE

1. Remove the cover from the power distribution

unit. 2. Remove the cover from the top of the cabinet

based on the cable route and cable

dimensions.

Cable Connection Reference

4.1

Installing a Ground Cable

4.2

1. Pull out the battery management module for

about 10 cm

3. Connect the ground cable.

1. Install the battery modules from bottom to top and from left to right to prevent falling over due to

imbalance.

2. Two persons are required to install the battery modules.

3. Place the front cover properly to prevent the light pipe from falling off.

InstallingBattery Modules and Cables

4.3

The 70 mm2ground cable is recom

mended.

NOTE

2. Install battery modules.

3. Remove front cover from the battery module,

and install battery baffle plate. 4. Install battery communications cables.

1. Communications cables between

the battery modules and the battery

management module are

preinstalled inside the cabinet.

2. Connect cables between the

battery modules and then connect

the cables to the battery

management module.

5. Open the battery terminal protective cover, install battery copper bars and cables.

1. During installation, wear insulation

gloves and use insulated tools.

2. Battery cables are preinstalled inside

the cabinet.

3. Install copper bars between the

battery modules, and then install

cables between the battery modules

and the battery management module.

4. Connect the round hole of the copper

bar to the upper battery module, and

then connect the waist hole of the

copper bar to the lower battery

module.

5. After the copper bar on each terminal

is secured, reinstall the protective

cover on the terminal.

6. Reinstall the battery management module.

1. Install power cables. 2. Install a control cable to the UPS.

InstallingOutput Cables

4.4

1. Install each cabinet in sequence

according to the installation method

of a single cabinet.

2. Combine cabinets.

3. Install a PE cable for each cabinet.

1. The SmartLi supports the

combination of up to five

cabinets.

2. When multiple cabinets are

connected in parallel, only the

basic cabinet has an LCD.

3. When cabinets are combined, a

battery bus bar box (BBB box) is

required. For details about how

to install a BBB box, see

PDU8000-(0630,1250, 2000)

DCV8-BGA001 BBB Box User

Manual.

CombiningCabinets

4.5

4. Connect battery cables.

5. Connect control cables.

The numbers of cabinets in a

parallel system depend on

the connection of control

cables. After the control

cables are connected

according to the preceding

figure, the cabinets are

numbered 1, 2, 3, 4, and 5

from top to bottom.

MUE05A

NOTE

Otros manuales para SmartLi Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unión Postal Universal de Huawei

Huawei

Huawei UPS2000-A-6KTTS-S Manual de usuario

Huawei

Huawei UPS2000-G Series Manual de usuario

Huawei

Huawei UPS2000-G-2KRTL Manual de usuario

Huawei

Huawei UPS5000-E-400K-FMS Manual de usuario

Huawei

Huawei UPS5000-E-600 kVA Manual de usuario

Huawei

Huawei UPS5000-S Series Manual de usuario

Huawei

Huawei Smartkits V100R002C00 Manual de usuario

Huawei

Huawei UPS5000-S Series Manual de usuario

Huawei

Huawei PDU8000 Series Manual de usuario

Huawei

Huawei UPS2000-G-6 kVA Manual de usuario

Huawei

Huawei UPS5000-E-600K-SC Manual de usuario

Huawei

Huawei UPS5000-E-****-FM series Manual de usuario

Huawei

Huawei UPS5000-H-800 Manual de usuario

Huawei

Huawei SmartLi 2.0 Manual de usuario

Huawei

Huawei UPS5000-S-880 kVA Manual de usuario

Huawei

Huawei PDU8000 Series Manual de usuario

Huawei

Huawei UPS5000-E-200K-SM Manual de usuario

Huawei

Huawei UPS5000-S-1200 kVA Manual de usuario

Huawei

Huawei UPS2000-G Series Manual de usuario

Huawei

Huawei UPS5000-S-1600 kVA Manual de usuario

Huawei

Huawei UPS5000-S Series Manual de usuario

Huawei

Huawei SmartLi-512V-162Ah-F Manual de usuario

Huawei

Huawei UPS5000-H Series Manual de usuario

Huawei

Huawei UPS5000-H-600 kVA-FTN Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario