Huawei UPS5000-E Series Manual de usuario

Issue: 08

Part Number: 31507658

Date: 2019-10-16

UPS5000-E-(550 kVA-600 kVA)

Quick Guide (50 kVA Power Modules)

UPS Model Weight Dimensions (H x W x D)

UPS5000-E-600K-SM/FM 1090 kg 2000 mm x 1400 mm x 850 mm

UPS5000-E-600K-SM UPS5000-E-600K-FM

(1) Power modules

(2) Control module

(3) Optional card slot

(4)

Power distribution module

covers

(5) Maintenance bypass switch

(6) Bypass module

(1)

Power modules

(2)

Control module

(3)

Optional card slot

(4) Mains input switch

(5) Output switch

(6) Power distribution

module covers

(7) Maintenance

bypass switch

(8) Bypass input switch

(9) Bypass module

2Installing the UPS

1. Channel steels and expansion bolts for securing the channel steels should be purchased by

the customer. The recommended channel steel width is 50 mm or more.

2. Ensure that the spacing between external sides of a channel steel is 800 mm. Secure channel

steels to the ground by using expansion bolts.

Scenario A: Channel steel mounting hole

Scenario B: Mounting holes on the floor

Unit: mm

Determining the UPS Installation Position2.1

NOTE

1. Before installation, read the user manual carefully to get familiar with product information and

safety precautions.

2. Use insulated tools during installation and operation.

3. Only engineers certified by the manufacturer or its agents are allowed to perform UPS

installation, commissioning, and maintenance. Otherwise, personal injury or equipment

damage may occur, and the resulting UPS faults are beyond the warranty scope.

4. This document describes how to install a single UPS. For details about how to install parallel

systems, contact Huawei technical support.

2.3 Install the front, rear, left, and right anchor baffle plates

2.2

(1)

Cabinet mounting holes (ground installation mode)

(2)

Cabinet mounting holes (channel steel installation mode)

Securing the UPS

•Floor mounting: Use eight M12x60 expansion bolts to secure the cabinet to the ground.

•Channel steel mounting: Use eight M12x60 common bolts to secure the cabinet to channel steels.

UPS Cable Connection Reference

3.1

•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps may

ignite and cause personal injury or device damage.

•After cables have been installed, clean the cabinets in a timely manner. Keep the cabinets and

surrounding environment clean and tidy.

•You need to prepare terminals onsite. The stripped length of the copper wire should be the

same as that of the part of the terminal that covers the conductor.

The cabling route is for reference only. Connect cables based on site requirements.

NOTE

3Connecting Cables

1. This document describes cable routing by removing the top cover when there are two mains

inputs.

2. In the case of single mains, you do not need to connect bypass input power cables and remove

short-circuit copper bars.

Connecting Cables

3.2

1. Open the front door of the bypass cabinet,

and remove front power distribution

covers.

2. Remove the cable covers from the top of the

cabinet. Then remove the beam, which is an

optional step.

4. Connect the ground cable to the UPS.

3. Remove the rear cover from the bypass

cabinet, and then remove the connecting

copper bars between mains input

terminals and bypass input terminals. (If

the mains input and bypass input share

a power source, skip this step.)

Scenario 1: Routing Cables from the Top

6. Connect the output power cable.

5. Connect the mains input power cable.

7. Connect bypass input power cables. 8. Connect the battery cable.

9. Connect signal cables.

Route a neutral wire from the middle of the

positive and negative battery strings.

Take a battery string consisting of 40

batteries as an example. A neutral wire

is routed from the middle of positive and

negative battery strings, each consisting of

20 batteries.

NOTE

Scenario 2: Routing Cables from the Bottom

For the screw specifications and torque

used for connecting cables in a bottom

cable routing scenario, refer to the top

cable routing scenario. This section only

shows the cable routes in the bottom cable

routing scenario.

NOTE

1. Remove the cable covers from the bottom of

the cabinet, drill holes in the covers, attach

grommet strips to the hole edges for

protecting cables, and reinstall the cable

covers.

2. Connect power cables and signal cables.

2. After verifying the installation, reinstall all

the covers.

3. (Remove the paper protective film from the

sealing putty.) After routing cables and

verifying cable connections, seal the gap

between cables and the cabinet using

sealing putty.

Dustproof cover

4. Do not remove the dustproof cover before

power-on to prevent dust inside the UPS.

Sealing putty

Sealing putty must be used as a whole and

the gap can be sealed only from the top.

Paper

protective film

4Installation Verification

1. Check that there is no foreign matter in the cabinet.

(1) Switches

(2) Mains input wiring

copper bars

(3) Battery input wiring

copper bars

(4) Output wiring

copper bars

(5) Bypass input wiring

copper bars

(6) Cabinet rear

1. Before powering on the UPS, ensure that the UPS has passed all check items in the UPS5000

Commissioning and Acceptance Report and Chapter 4.

2. Measure the voltage and frequency of the UPS upstream input switch. The line voltage range is

138–485 V AC, and the frequency range is 40–70 Hz.

Initial Startup

5.2

Download and install the Service Expert app.

After login, tap Power-on password activation

on the screen. A message is displayed,

indicating whether to start the UPS. Tap OK.

Insert the WiFi module into the USB port on the

MDU. Enable the mobile phone WLAN, search

for the UPS_WIFI signal, and connect to the

WiFi signal. The password is Changeme.

Set the Site and Device Type as required, and

connect the device. Set IP to 192.168.0.10, Port

to 443, Username to admin, Password to

Changeme, and click Login.

Enter Bar code and Verification code

obtained from the LCD on the Offline

Activation screen. Tap Generate PWD to

generate a startup password.

Set Site and Device Type as required,

and tap Offline Activation.

Enter the generated password in the

password textbox on the LCD to start the

UPS.

Use the app to

start the UPS

online?

Yes

No, start the

UPS offline

On the app home screen, tap StartUp to access the Set Startup screen.

•If the UPS is powered on for the first time, you need to obtain the startup password from the

Service Expert app. Skip this step if the UPS is not powered on for the first time.

•The Service Expert app can be downloaded from Google Play Store and can run on Android.

1. Obtain the startup password.

2. Set the language, time, date, network parameters, and system parameters on the Settings

Wizard screen.

Powering On the UPS

5.1

Close the upstream bypass and mains input switches.

(Full configuration model) Close the UPS bypass input switch, output switch, and mains input switch.

After the UPS is powered on, initialization begins. The MDU displays the Huawei logo and an

initialization progress bar.

5Powering On and Starting the UPS

3. After you perform the settings, the Bypass mode and No battery alarms are reported by the

MDU and do not need to be cleared. If there is any other alarm, you need to rectify the fault.

4. View the system running status diagram on the MDU to check that the UPS is working in bypass

mode.

System User LCD Preset Password WebUI Preset Password

admin (system administrator) 000001 Changeme

operator (common user) 000001 Changeme

To ensure system security,

change the LCD and WebUI

passwords after the first login.

NOTE

1. On the main menu, choose Common Functions and tap

Inv. ON.

2. In the displayed login window, enter the user name and

password, and tap .

3. In the displayed dialog box, tap Yes to start the inverter.

Starting inverter

5.3

Otros manuales para UPS5000-E Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unión Postal Universal de Huawei

Huawei

Huawei UPS5000-S200K-SM Manual de usuario

Huawei

Huawei UPS2000-A-6 kVA Manual de usuario

Huawei

Huawei UPS5000-E-400K-SM Manual de usuario

Huawei

Huawei UPS5000-E-80K-LABBS Manual de usuario

Huawei

Huawei UPS5000-E-30K-FM Manual de usuario

Huawei

Huawei UPS5000-S-1200 kVA Manual de usuario

Huawei

Huawei UPS5000-S-880 kVA Manual de usuario

Huawei

Huawei UPS5000-E-BF Series Manual de usuario

Huawei

Huawei UPS5000-A series Manual de usuario

Huawei

Huawei UPS5000-E-25K-SM Manual de usuario

Huawei

Huawei UPS5000-E Series Manual de usuario

Huawei

Huawei UPS5000-H-1200K-NT Manual de usuario

Huawei

Huawei SUN2000 Series Manual de usuario

Huawei

Huawei PDU8000 Series Manual de usuario

Huawei

Huawei UPS5000 Manual de usuario

Huawei

Huawei UPS5000-S Series Manual de usuario

Huawei

Huawei SUN2000-4.95KTL-JPL0 Manual de usuario

Huawei

Huawei SmartLi 2.0 Manual de usuario

Huawei

Huawei UPS5000-E-50K-HABBS Manual de usuario

Huawei

Huawei PDU8000 Series Manual de usuario

Huawei

Huawei UPS5000-E Series Manual de usuario

Huawei

Huawei UPS5000-S-1600 kVA Manual de usuario

Huawei

Huawei UPS5000-E-****-FM series Manual de usuario

Huawei

Huawei UPS2000-H Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario