Huawei OptiX PTN 3900 Manual de usuario
HUAWEI TECHNOLOGIES CO., LTD.
OptiX PTN 3900 Packet Transport Platform of PTN Series
Quick Installation Guide
Issue: 14
Date: 2013-07-30
Copyright © Huawei Technologies Co., Ltd. 2013. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address:
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website:
http://www.huawei.com
Email:
This document aims to provide simple and distinctive guidelines for hardware installation.
This document does not describe operations for the pre-delivery installation. Instead, this document
describes only the operations for on-site installation.
NOTE
Electrostatic Discharge
Before touching the device, or holding the boards and IC
chips, wear the anti-static wrist strap to prevent the
electrostatic discharge of the human body from
damaging the sensitive components. Ensure that the
other end of the antistatic wrist strap is well grounded.
Bundling Cables
The distance between cable ties or fiber binding straps inside the cabinet should be within 250 mm. (For
subscriber cable, the distance is 200mm. )
The distance between cable ties for all cables and corrugated pipes outside the cabinet is determined
according to the distance between two horizontal beams. For the cabling trough without beams, bundle the
cables with the distance not exceeding 250 mm between cable ties.
Pre-Installation Check
Verify that the equipment room, power supply, ground cables and optical cables are ready for installation.
Start the installation according to the engineering design documents after confirming that conditions are met.
Refer to the Installation Guide for information about specific operational requirements and technical
specifications.
Affixing Labels or Tags
Affix the label or tag to the signal cable, 2 cm away from the connector. When the cable is placed vertically,
the label or tag should point towards the right. When the cable is placed horizontally, the label or tag should
point downwards.
Precautions
2
2
Instructions and Precautions for Handling Boards
Do not hold a board without hand protection. Wear an ESD wrist strip or ESD gloves before handling a board.
Insert filler panels into vacant slots on an NE to prevent foreign matters from getting into the NE, which may
result in faults on the NE.
Boards are fragile and valuable. When handling or placing a board, exercise caution and put it into a
dedicated packing box.
Holding aboard without hand protectionWearing ESD gloves Wearing an ESD strip
Hold the front panel of a board with hands.
Tools for Installation
Tape measure Philips screwdriver Flathead screwdriver
Adjustable wrench Socket wrench Paper knife
Crimping pliers Cable cutter Wire stripper
Torque spanner Cable tester Multimeter
Electric soldering iron Hydraulic crimper Heat gun
Coax stripper Ethernet cable crimping pliers Diagonal pliers
3
Cabling Holes on the Top and at the Bottom of the Cabinet
2
Installing and Routing Power Cables
3
Contents
Installing and Routing Fibers
Upward Cabling
2
Downward Cabling
3
Installing the Cable Distribution Plate 1
2
Installing and Routing Cables
Overview of Cables
12
4
Installing and Routing Cabinet Indicator Cables
4
Installing and Routing Alarm Cables
514
Installing and Routing E1 Cables
616
Installing and Routing Ethernet Cables
720
Installing and Routing External Clock and Time Cables
821
Installing and Routing Network Management Cables 22
24
25
Connecting the Equipment Power Supply 27
1Open Corrugated Pipe 23
9
23
13
Appendix 28
Checking the Installation 26
1
Installing the Cable Distribution Plate
37th hole
Cable distribution plate
Panel screw
1st hole
22nd hole
36th hole
The holes are numbered from the bottom up. The hole at the bottom is numbered 1. The 73rd and 74th holes
are for installation of the upper cable distribution plate .
2
Installing and Routing cables
1
Overview of Cables
BGND power cable-48V power cable PGND cable
Subrack power
cable(positive)
Subrack power
cable (negative) 75-ohm 8 x E1
cable(1)
Alarm output and
concatenation cable
120-ohm 8 x E1
cable Cabinet indicator
cable
Two-Channel clock
transfer cables
One-Channel clock
transfer cables
3
2
Installing and Routing cables
Cabling Holes on the Top and at the Bottom of the Cabinet
Cabling holes on the top of the cabinet
Power cable hole
M8 grouding bolt
Fiber hole
Cabling hole
600mm
251mm
62mm
300mm
81mm
143mm
188mm
66mm
Fiber hole
Cabling hole Cabling hole Cabling hole
Cabling holes at the bottom of the cabinet
360mm
184mm
Cabling hole
Fiber hole
Cabling hole
Fiber hole
4
3
Installing and Routing cables
Installing and Routing Power Cables －Connection of Power Cables (TN81PDU)
Office grounding
bar
PGND cable
To office power supply
A
A
Subrack
power cable
Cabinet grounding
A
Subrack
power cable
connector
PIU
PWRB
PWRA
ALM
PIU
RTN1(+) NEG1(-)
RTN2(+) NEG2(-)
PIU
PWRB
PWRA
ALM
PIU
RTN1(+) NEG1(-)
RTN2(+) NEG2(-)
Power cables are classified into cabinet power cables and subrack power cables. The subrack power cables
are connected to the power distribution unit before delivery. Connect the subrack power cable connector to the
PIU board in the subrack during installation.
Tabla de contenidos
Otros manuales de Hardware de red de Huawei
Huawei
Huawei HW-TX-5000 Manual de usuario
Huawei
Huawei IDS2000 Dual-Row Aisle Containment Manual de usuario
Huawei
Huawei OceanStor S5600 Manual de usuario
Huawei
Huawei RRU3832 Manual de usuario
Huawei
Huawei CR52K-2xPOS/STM64 Manual de usuario
Huawei
Huawei RRU3971 Manual de usuario
Huawei
Huawei CR52-SFUD Manual de usuario
Huawei
Huawei ETP4860-B1A2 Manual de usuario
Huawei
Huawei CR52-RPR/STM64-XFP Manual de usuario
Huawei
Huawei CR52K-10GE-SFP Manual de usuario
Huawei
Huawei OptiX OSN 8800 T64 Manual de usuario
Huawei
Huawei CR-C2CF Manual de usuario
Huawei
Huawei RT-FIC-1CPOS Manual de usuario
Huawei
Huawei V600R019C00 Especificaciones técnicas
Huawei
Huawei FusionModule2000 V500R003C10 Especificaciones técnicas
Huawei
Huawei NetCo 15000-C30 Guía
Huawei
Huawei eAN3810A Guía de referencia rápida
Huawei
Huawei EchoLife EG8143H5 Manual de usuario
Huawei
Huawei FIC-1E1 Manual de usuario
Huawei
Huawei OptiX OSN 8800 Guía
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
