HUANUO HNCM7 Manual de usuario
(A
Monitor Desk Mount
Instruction Manual
Model: HNCM7
English ------------------------ 01-07
Deutsch ------------------------ 08-14
Français ------------------------ 15-21
Español ------------------------ 22-28
Italiano ------------------------ 29-35
Thank you for choosing this HUANUO product! At HUANUO, we strive to provide you with
the best quality products and services in the industry. Should you have any issues, please
don't hesitate to contact us.
Technical Support:
(US/CA)1-800-556-0533 Mon-Fri 8am - 8pm(CST)
(UK)44-808-196-3874 Mon-Fri 2pm - 10pm(UTC
Other Info:
Website: www.huanuoav.com
Manufacturer: BESTQI INNOATION (HONGKONG)TECHNOLOGY CO.,LIMITED
Address: RM21 UNIT A 11/F TIN WUI ING BLDG NO 3 HING WONG ST TUEN MUN NT HONGKONG
AMZLAB GmbH
Laubenhof 23,45326 Essen
THEMIS AR support ltd.
85 Great Portland St, London, United Kingdom.
Tools Needed (Not Included)
Phillips Screwdriver
Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly speci ed in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by incorrect assembly or inappropriate use.
• The desk must be capable of supporting ve times the weight of the monitor
and mount combined.
Check the VESA Pattern of Your Monitor before the Installation
IMPORTANT SAFETY INFORMATION
If your monitor VESA is greater than 100x100 mm/4x4 in or less than
VESA 75x75 mm/3x3 in, this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
MAX: 100mm/4 in
MAX: 100mm/4 in
Minimum VESA pattern:
75mm/3 in(W)x75mm/3 in(H)
100 mm 4 in
75 mm 3 in
Supplied Parts and Hardware
WARNING:This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, please contact our
• PLEASE NOTE:Not all hardware included in this package will be used.
01
3/8 in (10mm)
Socket Wrench
Drill(Optional)
7/16 in (11mm) -
7/8 in (22mm)
Drill(Optional)
Supplied Parts and Hardware for Step 1
02
Supplied Hardware for Step 4 and 5
1/8 in (3mm)
Small Allen Key
F3 (x1)
Nut
F4 (x2)
Washer
M6
D (x1)
Nut
M10
E2 (x1)
Bolt
M6X12mm
F (x1)
Bolt
M8X10mm
G (x2)
3/16 in (5mm)
Large Allen Key
F1
(x1)
5/32 in (4mm
Medium Allen Key
F2 (x1)
Locking Plate
a (x1)
C-Clamp Brace
02 (x1)
C-Clamp
03 (x1)
Pole
01 (x1)
Bottom Pad
b (x1)
Bolt
M6X8mm
H (x2)
Supplied Parts for Step 2
Decorative Cover
c (x1)
Arm
04 (x1)
Supplied Parts and Hardware for Step 3
Faceplate
05 (x2)
Bolt
M4x12mm
A (x8)
Bolt
M4x30mm
B (x8) L13mm Spacer
C1 (x8) M4 Washer
C2 (x8)
Step 1
Option A
C-Clamp Installation
Install the Base
03
02
02
01
03
Medium
Allen Key
Large
Allen Key
F2
H
F
Medium
Allen Key
F2
b
G
F1
04
Desk
Thickness
2 3/16 in (55mm) - 3 5/32 in (80mm)
Desk
Thickness
1 3/16 in (30mm) - 2 3/16 in (55mm)
Desk
Thickness
3/8 in (10mm) - 1 3/16 in (30mm)
b
Option B:
Grommet Installation
b
03a
03b
03b
01
03
D
a
03
D a
Tighten
D
a
D
a
05
Step 2 Secure the Arm [04] to the Pole [01]
If there is no grommet hole on your desk,
position the pole [01] on the mounting
surface and mark the hole. Drill a hole
using the drill bit in a diameter of
7/16 in - 7/8 in (11-22mm) at the marked
position through the mounting surface.
03b
3/4 in - 3 5/32 in
(20-80mm)
7/16 in - 7/8 in
(11-22mm)
a
E2
F1
c
Large
Allen Key
UP DeskDesk DeskDesk
Height Adjustment
04
01
WARNING
CASE If the head
is not straight.
Solution
06
A
Step 4 Hang the Monitor to the Arm [04]
Step 5 Adjustment
Step 3 Attach the Faceplate [05] the Back of Monitor
Use the Allen key [F3] to
slightly adjust the height of
each monitor.
Individual monitor height
adjustment helps monitors to
be perfectly aligned.
B
C1/C2
Flat back monitor Round back monitor
Small Allen Key
F3
Remove the nut [F4]
Slightly Adjust the Height of each Monitor
Phillips
Screwdriver
Not Included
F4
F4
07
1. Slightly loosen the
pre-assembled set screw
[T] .
2. Tilt monitor to your
desired angle.
3. Re-tighten the pre-as-
sembled set screw [T] to
hold monitor in place.
WARNING:
To avoid tipping, please be
careful not to extend the
arms too far forward or
backward. When you adjust
the angle of the arms,
please make sure two arms
are balanced to avoid
instability of the center of
gravity of the base.
F1
Tilt Adjustment
Large Allen Key
Tilt Adjustment
T
Swivel Swivel SwivelSwivel Swivel
Cable management
Cable Tie x 6
NOTE:
You can rotate the monitor or
swivel the arm manually.
08
Minimales VESA Muster:
75mm (Breite) x75mm (Höhe)
MAX:100mm
MAX:100mm
Benötigtes Werkzeug (nicht enthalten)
Kreuzschraubendreher
Bitte lesen Sie alle Anweisungen sorgfältig durch, bevor Sie instal lieren. Wenn
Sie dieses Handbuch nicht verstehen oder Fragen haben, wenden Sie sich bitte an
Attention: évitez les potentiels dommages corporels et aux biens.
• Ne pas utilizer ce produit dans le cas où cet instruction n’a pas indiqué. Ne pas
dépasser le poids limité. Nous ne sommes pas responsables des dommages
causés par le montage incorrect ou l’utilisation inappropriée.
• La table doit être capable de supporter au moins 5 fois du poids total (les poids
du socle, le moniteur et tous les accessoires), ne pas utiliser ce pruoduit dans un
panneau des particules.
Überprüfen Sie vor der Installation das VESA Muster des Monitore
Wichtige Sicherheitshinweise
Wenn Ihr Monitore-VESA größer als 100 x 100 mm oder weniger als
75x75mm ist, ist diese Installation NICHT kompatibel.
Wenn diese Halterung NICHT kompatibel ist, wenden Sie sich an den
Installation zu nden.
Mitgelieferte Teile und Hardware
WARNUNG:Dieses Produkt enthält kleine Gegenstände, die beim Verschlucken eine
Erstickungsgefahr verursachen können. Stellen Sie vor Beginn der Montage sicher, dass alle
Teile enthalten und nicht beschädigt sind. Verwenden Sie keine beschädigten oder defekten
Teile. Wenn Sie Ersatzteile benötigen, wenden Sie sich bitte an unseren Kundenservice unter
• Bitte beachten Sie: Es wird nicht alle in diesem Paket enthaltene Hardware verwendet.
10mm
SteckschlüsselBohrer(Optional) 11mm - 22mm
Bohrer(Optional)
09
Mitgelieferte Teile und Hardware für Schritt 1
Mitgelieferte Teile für Schritt 4 und 5
3mm
Kleiner Inbusschlüssel
F3 (x1)
Schraubenmutter
F4 (x2)
Unterlegscheibe
M6
D (x1)
Schraubenmutter
M10
E2 (x1)
Bolzen
M6X12mm
F (x1)
Bolzen
M8X10mm
G (x2)
5mm
Großer Inbusschlüsse
F1
(x1)
4mm
Mittlerer Inbusschlüssel
F2 (x1)
Verriegelungsplatte
a (x1)
C-Klemm platte
02 (x1)
C-Klemme
03 (x1)
Mast
01 (x1)
Unteres Pad
b (x1)
Bolzen
M6X8mm
H (x2)
Mitgelieferte Teile für Schritt 2
Dekorative Abdeckung
c (x1)
Arm
04 (x1)
Mitgelieferte Teile und Hardware für Schritt 3
Frontplatte
05 (x2)
Bolzen
M4x12mm
A (x8)
Bolzen
M4x30mm
B (x8)
L13mm
Abstandshalter
C1 (x8)
M4
Unterlegscheibe
C2 (x8)
Otros manuales para HNCM7
3
Tabla de contenidos
Idiomas:
Otros manuales de Rack y soporte de HUANUO
HUANUO
HUANUO HNQF2 Manual de usuario
HUANUO
HUANUO HNDS7 Manual de usuario
HUANUO
HUANUO HNDS8 Manual de usuario
HUANUO
HUANUO HNKB01 Manual de usuario
HUANUO
HUANUO HNTS4 Manual de usuario
HUANUO
HUANUO HNDS8 Manual de usuario
HUANUO
HUANUO HNPS01 Manual de usuario
HUANUO
HUANUO HNKB03 Manual de usuario
HUANUO
HUANUO HNQF2 Manual de usuario
HUANUO
HUANUO HNDSK4 Manual de usuario
HUANUO
HUANUO HNCM12 Manual de usuario
HUANUO
HUANUO HNSS12 Manual de usuario
HUANUO
HUANUO HNCM7 Manual de usuario
HUANUO
HUANUO HNCM16 Manual de usuario
HUANUO
HUANUO HNWSS1 Manual de usuario
HUANUO
HUANUO HNCM17 Manual de usuario
HUANUO
HUANUO HNCM3 Manual de usuario
HUANUO
HUANUO HNCM2 Manual de usuario
HUANUO
HUANUO HNDS11 Manual de usuario
HUANUO
HUANUO HNLL11 Manual de usuario
