HP STORAGEWORKS ALL-IN-ONE STORAGE SYSTEM Manual de usuario

<<bar code goes here in

text box, if applicable>>

201414- 003

hp StorageWorks

SDLT external tape drive

SDLT External Tape Drive Installation Instructions

Third Edition (October 2002)

Part Number: 201414-003

© Hewlett-Packard Company, 2002.

Hewlett-Packard Company makes no warranty of any kind with

regard to this material, including, but not limited to, the implied

warranties of merchantability and fitness for a particular purpose.

Hewlett-Packard shall not be liable for errors contained herein or for

incidental or consequential damages in connection with the

furnishing, performance, or use of this material.

This document contains proprietary information, which is protected

by copyright. No part of this document may be photocopied,

reproduced, or translated into another language without the prior

written consent of Hewlett-Packard. The information contained in this

document is subject to change without notice.

All other product names mentioned herein may be trademarks of their

respective companies.

Hewlett-Packard Company shall not be liable for technical or editorial

errors or omissions contained herein. The information is provided “as

is” without warranty of any kind and is subject to change without

notice. The warranties for Hewlett-Packard Company products are set

forth in the express limited warranty statements accompanying such

products. Nothing herein should be construed as constituting an

additional warranty.

installation

instructions

The HP SDLT tape drive requires a Wide-Ultra SCSI controller

or higher.

Step 1, Set the SCSI ID (Figure A)

Each SCSI device on the same SCSI bus must have a unique

SCSI ID. The default for HP tape drives is 6. If needed, change

the SCSI ID by pressing the button above or below the number

display on the back of the tape drive enclosure.

Note: SCSI ID 7 is reserved for the SCSI controller, two SCSI

controllers have IDs 6 and 7.

Step 2, Connect the Cables (Figure B)

1. Turn off the computer and any peripherals.

2. Attach the SCSI signal cable 1to the SCSI connector 2

located on the rear panel of the SDLT drive and then to the

external SCSI-2 port on the computer. Use the appropriate

SCSI cable for your computer SCSI connection. Two 6-ft

(1.8-m) cables are provided.

3. Attach the terminator (not shown) to the SCSI connector 3.

6

A

2

3

1

4

B

Page 2

4. Plug the tape drive AC power cord 4into the drive and

then plug the other end into a grounded AC outlet.

WARNING: To reduce the risk of electric shock or damage

to your equipment, do not disable the power cord

grounding feature. This equipment is designed for

connection to a grounded (earthed) power outlet. The

grounding plug is an important safety feature.

5. Turn on all peripheral devices and the computer.

Daisy Chaining - Optional Configuration

(Figure C)

Two SDLT tape drives can be connected to the same SCSI

channel at the same time. Use a 6-ft (1.8-m) cable to attach the

initial unit, then use a 3-ft (0.9-m) cable to daisy chain the

additional tape drive.

Note: Do not connect more than two tape drives per SCSI

controller. If using a low voltage differential (LVD) controller, more

than 2 drives can be connected per controller. Refer to your LVD

manual for cable configurations.

1. If the first drive unit has a terminator on the SCSI connector

1, remove it.

2. Connect the tape drives together by placing a SCSI cable

between the SCSI connector 2of the first drive to the SCSI

connector 3of the second drive.

3. Place the terminator (not shown) on the SCSI connector 4

of the second drive.

4. Turn on all peripheral devices and the computer.

Installation is complete. For more information about your tape

drive, refer to the HP StorageWorks SDLT Drive Reference

Guide that came with your tape drive.

1

2

3

4

C

Otros manuales para STORAGEWORKS ALL-IN-ONE STORAGE SYSTEM

8

Otros manuales de Almacenamiento de HP

HP

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manual de usuario

HP

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Manual de instrucciones

HP

HP StorageWorks MSA2000 Manual de usuario

HP

HP StorageWorks 2000fc Manual de instrucciones

HP

HP StoreOnce B6000 Manual de usuario

HP

HP D2D100 Manual de usuario

HP

HP StorageWorks 1000 - Modular Smart Array Manual de uso y cuidado

HP

HP D2D Manual de usuario

HP

HP StorageWorks Ultrium 215 Instrucciones de uso

HP

HP Surestore 6164 - Switch Manual de usuario

HP

HP P9000 Manual de usuario

HP

HP P9000 Manual de usuario

HP

HP StorageWorks XP1024 Guía rápida

HP

HP P9000 Manual de usuario

HP

HP StorageWorks 1000 - Modular Smart Array Manual de servicio

HP

HP StorageWorks 2300 - Disk System Manual de usuario

HP

HP P10000 Manual de usuario

HP

HP 3PAR StoreServ 7000 Manual técnico

HP

HP XP7 Manual de usuario

HP

HP c350b Manual de usuario

HP

HP P9000 Manual de usuario

HP

HP 6400/8400 Manual de usuario

HP

HP StorageWorks MSA 2/8 - SAN Switch Manual de usuario

HP

HP 345524-B21 Manual de usuario

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario

Dell

Dell PowerVault MD3600f Series Manual de usuario

CFI

CFI TERA STOR SATA RAID IV Manual de usuario