HP Designjet 8000s Take-Up Reel Kit Manual de usuario
HP Designjet 8000s Take-Up Reel Kit
Installation Guide
Legal notices
The information contained in this document
is subject to change without notice.
Hewlett-Packard makes no warranty of any
kind with regard to this material, including,
but not limited to, the implied warranties of
merchantability and fitness for a particular
purpose.
Hewlett-Packard shall not be liable for errors
contained herein or for incidental or
consequential damages in connection with
the furnishing, performance, or use of this
material.
No part of this document may be
photocopied or translated to another
language without the prior written consent of
Hewlett-Packard Company.
Installing the take-up reel
This Installation Guide contains information necessary to install and set up the HP Designjet 8000s
Take-up Reel Kit (Model Q6681A). For information about using the take-up reel, refer to the HP Designjet
8000s Printer User's Guide.
Two people will be required to install the take-up reel. Make sure there is enough space to access the
front and the rear of the printer. All mechanical installation takes place from the front of the printer and
electrical connections are made at the rear.
The tool you need to install the take-up reel is included in the box, and consists of a cross-head (Phillips)
screwdriver.
To install the take-up reel:
1. Open the box and remove all parts.
1. Left end plate. 4. Take-up reel assembly.
2. Right end plate. 5. Motor cable.
3. Media sensor assembly. 6. Tension bar.
ENWW 1
Installing the take-up reel
2. Install the right end plate as follows:
a. Insert the lip (1) on the right end plate into the slot (2) on the right leg on the printer stand.
b. Install three screws (1) to fix the right end plate to the right printer leg stand.
3. Install the left end plate as follows:
a. Insert the lip on the left end plate into the slot on the left leg on the printer stand.
b. Install three washers (1) and screws (2) to fix the left end plate to the left printer leg stand.
NOTE The left end plate allows for vertical movement so that the take-up reel height
can be adjusted even with the screws fully inserted.
2 Installing the take-up reel ENWW
Installing the take-up reel
4. Install the take-up reel assembly as follows:
a. Place the take-up reel assembly (3) onto the printer stand crossbar.
b. Rest the ends of the support bar (2) on the ledges (1) on each end plate.
5. Install the holding bracket (1) at each end to secure the support bar as follows:
ENWW 3
Installing the take-up reel
a. Install the bottom of the holding bracket into the slot (2) on the end plate.
b. Install one screw (1) into each holding bracket to secure it to the end plate.
6. Turn the take-up reel stop screws (1) anti-clockwise to release the right and left assemblies.
4 Installing the take-up reel ENWW
Installing the take-up reel
7. Slide the left (1) and right (2) take-up reel assemblies to the right and left ends of the support bar.
Remove the assembly packaging (3).
8. Turn the take-up reel stop screws (1) clockwise to lock the right and left take-up reel assemblies.
9. Install one screw (2) to secure the take-up reel media sensor assembly (1) to the right stand.
10. At the rear of the printer, insert the following connectors into the rear of the right take-up reel
assembly and secure them with the cable clip (3):
a. Insert the media sensor connector (1).
b. Insert the take-up reel motor cable connector (2).
ENWW 5
Installing the take-up reel
11. Insert the connector on the other end of the motor cable (1) into the rear of the printer.
12. Secure the motor cable with the three cable clips (1) on the rear of the printer.
6 Installing the take-up reel ENWW
Installing the take-up reel
13. Load the tension bar (1) into the take-up reel.
The height of the take-up reel may require adjustment as it must be horizontally aligned to the media
output from the printer. Refer to the next section to verify alignment of the take-up reel height.
Take-up reel horizontal alignment
The height of the take-up reel may require adjustment as it must be horizontally aligned to the media
output from the printer. To verify alignment of the take-up reel height you need to print the take-up reel
test print.
The printer will print a line across the width of the media. Use this line to check the alignment of the right
side of the take-up reel with the left side. Use the take-up reel tension bar as the horizontal reference
for alignment.
Print the take-up reel pattern on roll media to ensure that there is sufficient length to feed the media to
the tension bar on the take-up reel.
Print the take-up reel print as follows:
1. When the "Printer Ready" message appears on the Front Panel, press the ONLINE key to take the
Printer offline.
2. Press the SHIFT key twice and select the ADJUST menu using the ◄key.
3. In the ADJUST submenu, scroll to TEST PRINTS and press the ENTER key.
4. In the TEST PRINTS menu scroll to the TUR ADJ PRINToption and press the ENTER key.
5. Press the ENTER key to start printing the pattern.
ENWW Take-up reel horizontal alignment 7
Installing the take-up reel
The printer automatically feeds the media through the printer so that the pattern reaches the take-up
reel tension bar.
If the pattern (2) on the right and left edge of the media is aligned with the same groove (1) on the tension
bar, no height adjustment is required.
If the pattern on the left edge of the media is not aligned with the same groove as on the right edge, use
the take-up reel height screw (1) to adjust the take-up reel height up (2) or down (3).
Only the left side of the take-up reel can be adjusted up or down.
8 Installing the take-up reel ENWW
Installing the take-up reel
Otros manuales de Accesorios de impresora de HP
HP
HP LaserJet 4200dtn Manual de usuario
HP
HP C Manual de usuario
HP
HP 5100 - LaserJet B/W Laser Printer Manual de usuario
HP
HP Ink Tank 110 series Manual de usuario
HP
HP Digital Sender 8100C Manual de usuario
HP
HP C2H57A Manual de usuario
HP
HP c9704a Hoja de instrucciones
HP
HP 3500 - Color LaserJet Laser Printer Manual de usuario
HP
HP Laserjet,Color Laserjet 4350 Manual de usuario
HP
HP LaserJet M5035 Series Manual de usuario
HP
HP C2655A - Deskjet 340 Color Inkjet Printer Manual de usuario
HP
HP c9700a Hoja de instrucciones
HP
HP Officejet 100 Manual de usuario
HP
HP LaserJet Enterprise M4555 Manual de usuario
HP
HP Color LaserJet CP3520 Manual de usuario
HP
HP Color LaserJet CP3520 Manual de usuario
HP
HP Jetdirect 2800w Manual de usuario
HP
HP ScanJet Scanners Manual de usuario
HP
HP Designjet 10000s series Manual de usuario
HP
HP LaserJet M4345 - Multifunction Printer Manual de usuario
