HP NetStorage 6000 Guía de inicio rápido

Otros manuales para NetStorage 6000

12

Este manual sirve para los siguientes modelos

1

Otros manuales de Servidor de almacenamiento en red de HP

HP

HP X1800sb Instrucciones de uso

HP

HP DL320s - ProLiant 9TB SATA Storage Server... Cómo utilizar

HP

HP NAS 4000s Manual de usuario

HP

HP 3PAR StoreServ 7000 Manual de usuario

HP

HP StorageWorks P4000 Series Guía de referencia rápida

HP

HP ML370 - ProLiant - G3 Manual de usuario

HP

HP StorageWorks NAS e7000 v2 Manual de usuario

HP

HP NetStorage 6000 Manual de instrucciones

HP

HP EX495 - 1.5TB Mediasmart Home Server Manual de usuario

HP

HP Proliant DL580 Manual de usuario

HP

HP J3278B - SureStore CD-ROM Server/Tower 7 NAS... Manual de usuario

HP

HP ProLiant DL100 G2 DPSS Manual de usuario

HP

HP EX495 - 1.5TB Mediasmart Home Server Instrucciones de instalación

HP

HP ProLiant Server Manual del operador

HP

HP 3PAR StoreServ 7000 Manual de usuario

HP

HP ProLiant ML310 G3 1TB Manual de usuario

HP

HP StorageWorks E Series Manual de usuario

HP

HP AK373A - StorageWorks All-in-One Storage System 1200r 5.4TB SAS Model NAS... Cómo utilizar

HP

HP ML350 - ProLiant - G2 Manual de usuario

HP

HP X300 Data Vault Guía de instalación

HP

HP ProLiant ML110 G1 Manual de usuario

HP

HP ProLiant DL380 G4 DPSS Manual de usuario

HP

HP ML110 - ProLiant G5 2TB Storage Server NAS Cómo utilizar

HP

HP ProLiant 300 Series Manual de instrucciones

Manuales populares de Servidor de almacenamiento en red de otras marcas

Seagate

Seagate U10 ST320423A Manual de usuario

Synology

Synology RackStation RS816 Manual

D-Link

D-Link ShareCenter Pro DNS-1200-05 Manual de usuario

Avid Technology

Avid Technology VideoRAID ST Guía de seguridad

Western Digital

Western Digital My Cloud Home Duo Manual de usuario

PrimeArray

PrimeArray 4xxx Manual de usuario

Buffalo

Buffalo TeraStation WSS WSH5010N6 Manual de usuario

Planex

Planex MZK-NAS01SG Manual de usuario

Intel

Intel SS4000-E - Entry Storage System NAS Server Manual de usuario

Synology

Synology RS2212+ Manual de usuario

Allnet

Allnet ALL69000 Manual de usuario

Adaptec

Adaptec 5325301580 Manual de usuario

Motorola

Motorola EXORdisk II Manual de usuario

Sony

Sony XDAAI1PK Manual de usuario

Cisco

Cisco Linksys NAS200 Instrucciones de funcionamiento originales

Sans Digital

Sans Digital MR4UT6G Manual de usuario

AIC

AIC FB128-LX Manual de usuario

Dell

Dell PowerVault NX3500 Instrucciones de uso

Storage Upgrade

HP NETSTORAGE 6000

Before You Begin:

•You must add at least three hard drives for this procedure.

•Use only HP Hard Drives approved for your HP NetStorage 6000. For an up to date list of

approved hard disk drives, please visit our web site at http://www.hp.com/support/ns6000.

Drives on the approved list have custom firmware for use in your NetStorage 6000. Do not

attempt to install any hard disk drives other than the approved drives listed at this web site

as doing so may result in system failure or loss of data. Using non supported hard drives

may also void your warranty.

•Use only hard drives that are the same capacity as the drives that originally came with your

HP NetStorage 6000 device. Do not mix different capacity hard drives.

•You can upgrade storage while the unit is operational.

•To insure proper cooling of the unit, do not remove empty filler shuttles until you are ready

to replace them with new hard drives.

Remove Empty Drive Shuttles

A. Open the front panel door, and unlock the drive

shuttles.

B. Loosen the thumbscrew, and remove as many

empty shuttles as needed to accomodate the new

drives.

CAU ION: Do not remove drives that are already

present or you may lose data.

Parts Required:

•New drives

•Key for physically unlocking the hard drives

•Phillips screwdriver

•Electrostatic protection device

A. If an open drive bay still exists, remove the empty drive shuttle and

install the new spare drive.

B. If an open drive bay does not exist, carefully determine

which existing hard drive is the current hot spare using the

Storage > Logical Drives page in the web interface. The drive bays

are numbered from left to right. Remove the current spare drive

and install the new one.

NO E: If you accidentially removed a hard drive that is assigned to

a logical drive, the system will fail over to the existing hot spare.

Wait for the rebuilding process to complete, and install the new hot

spare in the same bay as the drive you just removed.

Install the New Hot Spare (if needed)

Use a Web Browser to Create a Logical Drive

A. Open a web browser and enter the unit's IP address in the browser's

address or location field.

B. Locate the new drives by selecting Storage > Physical Drives.

These drives will have Unassigned in the Assignment field.

NO E: It may take a few minutes for the new drives to show up on

the user interface. Click Actions > Refresh to update the display.

C. If you are upgrading your hot spare, select Actions > Assign Hot

Spares. Select the drive that you want to be the spare, and click OK.

D. To assign drives to a new logical drive, select Actions > Create

Logical Drive. Select the drives to be included in the new logical

drive, and click OK.

NO E: For information on creating or expanding file volumes,

refer to the HP NetStorage 6000 User’s Guide.

Install New Hard Drives

A. Loosen the shuttle lever thumbscrew on the new hard drive.

B. Slide the hard drive into the empty bay.

C. Fully seat the drive by lifting the lever and pushing rearward while

lowering the lever. The top of the lever will engage with the rail at

the top of the drive bay. Lower the lever, securing the drive in place.

D. Tighten the thumbscrew.

E. Use the key to lock the hard drives in place.

*C4484-90100*

C4484 90100