Cisco Linksys NAS200 Instrucciones de funcionamiento originales

Network Storage

System with 2 Bays

Model No: NAS200 (EU)

QUICK INSTALLATION

English

Deutsch

Español

Français

Italiano

Nederlands

Português

Table of Contents

Online Resources

Most web browsers allow you to enter the web address without adding the

http:// in front of the address. This User Guide will refer to websites without

including http:// in front of the address. Some older web browsers may require

you to add it.

Resource Website

Linksys www.linksys.com

Linksys Europe www.linksys.eu

Linksys International www.linksys.com/international

Glossary www.linksys.com/glossary

Network Security www.linksys.com/security

Specifications are subject to change without notice. Linksys is a registered

trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and

Other brands and product names are trademarks or registered trademarks of

their respective holders.

TableofContents........................................................3

Installation(English)...............................................4

Installation(Deutsch).............................................14

Instalación(Español)..............................................24

Installation(Français) .............................................34

Installazione(Italiano) ............................................44

Installatie(Nederlands) ...........................................54

Instalação(Português)............................................64

ContactInformation....................................................74

Installation (English)

NOTE: The Network Storage System supports up to two 3.5-inch,

Serial-ATA (SATA) hard drives, so use hard drives equipped with the

SATA interface. Before you begin, back up any pre-existing data

because all data on your hard drives will be erased.

WARNING: Low-prole or half-height hard drives can be used at your

own risk; however, Linksys does not support the use of these drives

as they are not securely held in place inside the Network Storage

System.

Make sure the Network Storage

System is powered off.

Insert the Setup Wizard CD-ROM

into your computer’s CD-ROM

drive. The Setup Wizard should run

automatically, and the Welcome

screen should appear. If it does not,

click Start and then Run. In the

field provided, enter

D:\SetupUtility.exe (if“D” is the

letter of your CD-ROM drive).

If a language selection screen

appears, select your preferred

language. Then click Next/Install.

Click the Click Here to Start

button.

Insert the CD-ROMInsert the CD-ROM

Click Here to StartClick Here to Start

Installation

For first-time installation, click Set

up NAS200.

Read the License Agreement, and

click Next to accept it.

The screen describes the Setup

Wizard steps you will perform. Click

Next.

Set up NAS200Set up NAS200

License AgreementLicense Agreement

Setup Wizard StepsSetup Wizard Steps

Installation

Make sure your hard drives use

the SATA interface. These drives

must be formatted by the Network

Storage System. Make sure you

back up all pre-existing data before

the Network Storage System erases

and formats your hard drives. Click

Next.

For physical installation, follow

these instructions:

Push together the clips, and

remove the drive bay door. (If

you have only one drive, install

it in the upper bay.)

Lift up the ribbon.

Make sure the connector side

of the drive faces the bay, and

the label side faces up.

Make sure the drive is inserted under the ribbon.

Push the drive in until it snugly fits in the bay.

Replace the drive bay door.

If you have a second hard drive, repeat these steps for the lower bay.

NOTE: If you install a second drive and plan to stripe (RAID 0) or

mirror (RAID 1) these drives, then match the drive sizes for maximum

drive use.

Click Next.

SATA Hard DrivesSATA Hard Drives

Install Hard DriveInstall Hard Drive

Installation

Connect one end of the included

Ethernet network cable to the

Ethernet port of the Network

Storage System.

Connect the other end to one of

the router’s local network ports.

Click Next.

Connect the power adapter to the

Power port of the Network Storage

System.

Connect the power cord to the

power adapter. Plug the power cord

into an electrical outlet.

Press the Power button on the

back panel of the Network Storage

System. The Network Storage

System beeps once when it is ready.

Click Next.

Connect Network CableConnect Network Cable

Connect PowerConnect Power

Installation

While the Network Storage System

is booting up, the Power LED on the

front panel flashes.

Wait until you hear the Network

Storage System beep twice. (Be

patient; this can take several

minutes.)

The Power and Ethernet LEDs are

lit. The Disk 1 LED is lit if you have

installed a drive in the upper bay.

The Disk 2 LED is lit if you have

installed a drive in the lower bay.

Click Next.

The Setup Wizard automatically

searches for any Network Storage

System on your network.

If the Network Storage System

is not detected, check its cable

connections, and make sure it is

powered on. Then click Search

Again to locate the Network

Storage System.

Select the Network Storage System

that you want to set up. Then click

Next.

Wait for Two BeepsWait for Two Beeps

Network Storage System DetectedNetwork Storage System Detected

Installation

Enter a descriptive name for the

Network Storage System. Click

Next.

If you have a router or other

DHCP server automatically

assigning IP addresses, then select

Automatically obtain an IP

address (DHCP recommended)

and click Next. (If you are not sure

which option to select, then select

this option.)

Proceed to step P.

NOTE: If you need more information, click Help.

To manually set the Network

Storage System’s network settings,

select Set IP conguration

manually and enter the following

information:

IP Address Enter the Network

Storage System’s IP address, and

make sure that it is on the same

local area network (LAN) segment

as the computer running the Setup

Wizard.

Enter Descriptive NameEnter Descriptive Name

Automatic Network SettingsAutomatic Network Settings

Manual Network SettingsManual Network Settings

Installation

Subnet Mask Enter the Subnet Mask, which must match the subnet mask

of the other devices on your network. The default is 255.255.255.0.

Gateway If you have a router on your network, enter its IP address. The

default is 192.168.1.1.

Click Next.

Select the appropriate

configuration for your drive usage:

WARNING: Before you format

drive(s), back up pre-existing

data because all data on your

drive(s) will be erased when

they are formatted.

NOTE: If you need more

information, click Help.

Maximum Storage - Two separate disks (Recommended) Drives seen

separately.

Maximum Storage - Two disks configured as one large disk

(JBOD/LVM) Drives seen as a single virtual drive.

Maximum Data Security - Mirroring (RAID 1) Requires two hard drives.

Maximum Speed - Striping (RAID 0) Requires two hard drives.

Click Next.

Select Drive ConfigurationSelect Drive Configuration

Installation

Review the new settings. If they

are correct, click Save. If you would

like to change them, click Back to

return to the previous screen.

To confirm that you want to format

your drives and erase all data on

them, click Next.

WARNING: Before you format

drive(s), back up pre-existing

data because all data on your

drive(s) will be erased when

they are formatted.

NOTE: When formatting is complete, the Network Storage System is

congured. You can map it to computers or use the Network Storage

System without mapping.

The following steps map the

network drive(s) to your computer

for convenient access.

Click Set up Computer.

Confirm New SettingsConfirm New Settings

Confirm FormattingConfirm Formatting

Set up ComputerSet up Computer

Otros manuales para Linksys NAS200

Tabla de contenidos

Idiomas:

Otros manuales de Servidor de almacenamiento en red de Cisco

Cisco

Cisco ASR 5000 Series Manual de instrucciones

Cisco

Cisco UCS 6400 Series Manual

Cisco

Cisco C880 M4 Manual del propietario

Cisco

Cisco Smart Storage NSS322 Manual de usuario

Cisco

Cisco NSS2000 - Gigabit Storage System Chassis Manual de instrucciones

Cisco

Cisco Linksys NAS200 Manual de usuario

Cisco

Cisco UCS S3260 Guía de inicio rápido

Manuales populares de Servidor de almacenamiento en red de otras marcas

HP NetStorage 6000 Manual de usuario

Seagate

Seagate U10 ST320423A Manual de usuario

Synology

Synology RackStation RS816 Manual

D-Link

D-Link ShareCenter Pro DNS-1200-05 Manual de usuario

Avid Technology

Avid Technology VideoRAID ST Guía de seguridad

Western Digital

Western Digital My Cloud Home Duo Manual de usuario

PrimeArray

PrimeArray 4xxx Manual de usuario

Buffalo

Buffalo TeraStation WSS WSH5010N6 Manual de usuario

Planex

Planex MZK-NAS01SG Manual de usuario

Intel

Intel SS4000-E - Entry Storage System NAS Server Manual de usuario

Synology

Synology RS2212+ Manual de usuario

Allnet

Allnet ALL69000 Manual de usuario

Adaptec

Adaptec 5325301580 Manual de usuario

Motorola

Motorola EXORdisk II Manual de usuario

Sony

Sony XDAAI1PK Manual de usuario

Sans Digital

Sans Digital MR4UT6G Manual de usuario

AIC

AIC FB128-LX Manual de usuario

Dell

Dell PowerVault NX3500 Instrucciones de uso