HP HPE Synergy 12000 Frame Instrucciones de funcionamiento y seguridad

HPE Synergy 12000 Frame Setup and Installation GuideHPE Synergy 12000 Frame Setup and Installation Guide

Part Number: 30-5842950C-008

Published: April 2022

Edition: 8

HPE Synergy 12000 Frame Setup and Installation GuideHPE Synergy 12000 Frame Setup and Installation Guide

AbstractAbstract

This document describes identification, installation, and setup for the HPE Synergy System. This guide is for an experienced service

technician. Hewlett Packard Enterprise assumes you are qualified in the servicing of the HPE Synergy components and overall solution.

Part Number: 30-5842950C-008

Published: April 2022

Edition: 8

NoticesNotices

The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and

services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as

constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained

herein.

Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or copying. Consistent with FAR

12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed

to the U.S. Government under vendor's standard commercial license.

Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard Enterprise has no control over and is

not responsible for information outside the Hewlett Packard Enterprise website.

AcknowledgmentsAcknowledgments

Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

® ®

Table of contentsTable of contents
Planning the installation
1 Safety and regulatory compliance
2 Site requirements
3 Warning, caution, and important messages
4 Determine power and cooling configurations
4.1 Power supply calculations
4.2 Power requirements
5 Space and airflow requirements
6 Temperature requirements
7 Grounding requirements
8 Supported racks and rack options
8.1 Rack-free environment requirements
9 HPE Synergy configuration
10 Pallet contents
Component and LED identification
1 Information pull tabs
2 Frame front components and device bays
2.1 Device bay numbering
2.1.1 Device bay partitions
2.2 Front panel components
2.3 Appliance module LEDs and components
2.3.1 Appliance bay numbering
2.4 Compute module LEDs and buttons
2.4.1 System power LED definitions
2.4.2 NVDIMM LED identification
2.4.2.1 NVDIMM-N LED combinations
2.4.2.2 NVDIMM Function LED patterns
2.5 Storage module LEDs
3 Frame rear components
3.1 Rear component bay numbering
3.2 HPE Synergy 4-Port Frame Link Module components and LEDs
3.3 HPE Synergy Frame Link Module components and LEDs
3.4 Power supply LED
3.5 Fan LED
3.6 HPE Synergy 10Gb Interconnect Link Module LEDs and buttons
3.7 HPE Synergy 10Gb Interconnect Module interconnect link port
3.8 HPE Synergy 20Gb Interconnect Link Module LEDs and buttons
3.9 HPE Synergy 20Gb Interconnect Link Module interconnect link ports
3.10 HPE Synergy 50Gb Interconnect Link Module LEDs and buttons
3.11 HPE Synergy 50Gb Interconnect Link Module interconnect link ports
3.12 HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy LEDs and buttons
3.13 HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy components

3.14 HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy LEDs and buttons
3.15 HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy components
3.16 HPE Synergy 40Gb F8 Switch Module LEDs and buttons
3.17 HPE Synergy 40Gb F8 Switch Module components
3.18 Mellanox SH2200 Switch Module for HPE Synergy LEDs and components
Installation
1 Installing the Synergy system components
2 Removing components from the frame
3 Installing the frame in a rack-free environment
4 Installing the frame in a rack
4.1 Measuring with the rack template
4.2 Installing the rack rails for a square-hole rack
4.3 Installing the rack rails for a round-hole rack
4.4 Installing the frame into the rack
5 Component installation
5.1 Installing an appliance module
5.2 Configuring the device bays
5.2.1 Creating a full-height module bay blank
5.2.2 Removing a device bay shelf
5.2.3 Installing a device bay shelf
5.2.4 Removing the half shelf
5.2.4.1 Replacing the half shelf
5.2.5 Installing the half shelf
5.3 Installing compute modules
5.3.1 Installing a full-height compute module
5.3.2 Installing a half-height compute module
5.4 Installing a frame link module
5.5 Installing the storage module
5.6 Installing drives in the storage module
5.7 Installing fans
5.8 Installing interconnect modules
5.8.1 Interconnect module configurations
5.8.1.1 Interconnect module installation guidelines
5.8.1.2 Master interconnect module with interconnect link module configurations
5.8.2 Mezzanine to frame signal routing
5.8.3 Interconnect port mapping
5.8.4 Half-height compute module mezzanine connector definitions
5.8.5 Full-height compute module mezzanine connector definitions
5.9 Installing power supplies
5.9.1 Power supply configurations
5.10 Installing a DC power supply
5.10.1 Warnings and cautions
5.10.2 Installing the DC power grounding kit (no bracket)
5.10.3 Installing the DC power grounding kit (with bracket)

6 Cabling the frame
HPE Synergy Cabling
Configuring HPE Synergy
1 Configuration overview
1.1 HPE Synergy Console connections
1.1.1 Connecting to the HPE Synergy Console using a laptop computer
1.1.2 Connecting to the HPE Synergy Console using a keyboard, video monitor, and mouse
1.1.3 HPE Synergy Console Frame Health & Inventory screen
1.2 Run hardware setup
1.3 Remotely connect to HPE OneView
1.4 Configure Network Time Protocol
1.5 Add IP and subnet address ranges
1.6 Configure the hardware in HPE OneView
1.6.1 Create a network
1.6.2 Create a logical interconnect group
1.6.3 Define an enclosure group
1.6.4 Create a logical enclosure
1.6.5 Create a server profile
1.7 Update the firmware
1.7.1 Update the HPE Synergy appliance firmware
1.7.1.1 Single frame configurations with redundant Composers and only a single frame link module
1.7.2 Add a firmware bundle to the appliance firmware repository
1.8 Configure HPE Synergy Image Streamer
1.8.1 Configuring HPE Synergy Image Streamer
1.8.2 Configuring HPE OneView to deploy OS build artifacts to compute modules
1.9 Configure additional settings
Troubleshooting
1 Symbols on equipment
2 Error screens when connecting to the HPE Synergy Console
2.1 HPE Synergy Console not responding
2.2 Frame not claimed by an HPE Synergy Console
2.3 The HPE Synergy Console cannot connect to HPE OneView
2.4 HPE Synergy Console icons
3 Issues during installation
4 HPE Synergy Console
4.1 Accessing the HPE OneView Maintenance Console from the frame link module
4.2 Connecting to the HPE OneView maintenance console using SSH
4.3 Creating a support dump file
5 Resetting to factory settings
5.1 Resetting the appliance module to the original factory settings
5.2 Frame link module factory reset
5.3 Performing a frame link module factory reset
HPE Synergy documentation resources
1 HPE Synergy firmware update resources

HPE Synergy documentation map
Specifications
1 HPE Synergy QuickSpecs
Electrostatic discharge
Support and other resources
1 Accessing Hewlett Packard Enterprise Support
2 Accessing updates
3 Remote support
4 Customer self repair
5 Warranty information
6 Regulatory information
7 Documentation feedback
Acronyms and abbreviations

Planning the installationPlanning the installation

Planning the installation 7

Safety and regulatory complianceSafety and regulatory compliance

For important safety, environmental, and regulatory information, see Safety and Compliance Information for Server, Storage, Power,

Networking, and Rack Products, available at the Hewlett Packard Enterprise website ( https://www.hpe.com/support/Safety-Compliance-https://www.hpe.com/support/Safety-Compliance-

EnterpriseProductsEnterpriseProducts).

Safety and regulatory compliance 8

Site requirementsSite requirements

Select an installation site that meets the detailed installation site requirements described in the site planning guide on the Hewlett

Packard Enterprise website (http://www.hpe.com/info/synergy-docshttp://www.hpe.com/info/synergy-docs).

Site requirements 9

Warning, caution, and important messagesWarning, caution, and important messages

WARNING:WARNING:

To reduce the risk of personal injury or damage to equipment, heed all warnings and cautions

throughout the installation instructions.

WARNING:WARNING:

To reduce the risk of personal injury or damage to the equipment, be sure that:

The leveling feet are extended to the floor.

The full weight of the rack rests on the leveling feet.

The stabilizing feet are attached to the rack if it is a single-rack installation.

The racks are coupled together in multiple-rack installations.

Only one component is extended at a time. A rack may become unstable if more than one

component is extended for any reason.

WARNING:WARNING:

The frame is very heavy. To reduce the risk of personal injury or damage to the equipment:

Observe local occupational health and safety requirements and guidelines for manual

material handling.

Remove all installed components from the frame before installing or moving the frame.

Use caution and get help to lift and stabilize the frame during installation or removal,

especially when the frame is not fastened to the rack.

WARNING:WARNING:

When lifting the frame with the optional removable handles, always use at least four people to

lift the frame into the rack. If the frame is being loaded into the rack above chest level, a fifth

person must assist with aligning the frame with the rails while the other four people support the

weight of the frame. If you are using a mechanical lift to install the frame, two people are

required to install the frame into the rack.

WARNING:WARNING:

Install the frame starting from the bottom of the rack and work your way up the rack.

These symbols, on power supplies or systems, indicate that the equipment is supplied by multiple sources of

power.

NOTE:NOTE:

To reduce the risk of injury from electric shock, remove all power cords to completely disconnect

power from the system.

Each frame has two or more power supply cords. A single rack or cabinet may contain more than

one frame. Power may be supplied in a redundant fashion. Removing any single source of power

does not necessarily remove power from any portion of the system. When performing any service

other than hot-plug module replacement, you must completely disconnect all power to that

portion of the system.

When performing service procedures on frames, shut off the circuit breakers to both A and B AC

power feeds and then disconnect all power cords from the outlets before servicing.

Warning, caution, and important messages 10

Otros manuales para HPE Synergy 12000 Frame

Tabla de contenidos

Otros manuales de Hardware de red de HP

HP StorageWorks X9720 Manual de servicio

HP A3550A - High Availability Disk Arrays Model 20 Storage... Manual de usuario

HP StorageWorks 2324fc Manual de usuario

HP 12500 Series Manual de usuario

HP AHA-8940 Manual de usuario

HP StorageWorks x9300 Manual de servicio

HP X5000 G2 Manual de servicio

HP A3550A - High Availability Disk Arrays Model 20 Storage... Manual de usuario

HP MSR954 Series Instrucciones de montaje

HP StorageWorks 1/8 Tape Autoloader Manual de usuario

HP zl2 Manual de usuario

HP c-Class Guía de instalación

HP E-MSM466-R Instrucciones de montaje

HP procurve radio port 220 Instrucciones de montaje

HP Wireless LAN 802.11b/g Device WN4201B Manual de usuario

HP 30020B Manual

HP 82713A Manual de usuario

HP E1459A Manual de usuario

HP JG602A Manual de usuario

HP Mv2120 - Media Vault Network Drive Manual de usuario

HP StoreOnce 4700 Guía de instalación y uso

HP X1800sb G2 Instrucciones de uso

HP Deskjet 870 Manual de usuario

HP ARUBA 8320 48 10/6 40 X472 5 2 Bdl Instrucciones de montaje

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario