HP 20wd Manual de usuario

HP 20wd LED Backlit Monitor

User Guide

Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft

Corporation in the United States and/or other countries.

The only warranties for HP products and services are set forth in the express warranty statements

accompanying such products and services. Nothing herein should be construed as constituting an

additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

This document contains proprietary information that is protected by copyright. No part of this document

may be photocopied, reproduced, or translated to another language without the prior written consent of

Hewlett-Packard Company.

First Edition (January 2014)

Document Part Number: 751598-001

Chapter I. Introduction

1.1 Features

Multilingual OSD adjustment

Compatible with IBM VGA, extended VGA, VESA VGA, SVGA, XGA, and SXGA modes

Wide range of applicable voltages (AC 100-240V 50/60Hz) enables direct use without any

setting.

Plug-and-play VESA DDC1/ 2B Standard. Compatible with Windows 9x / 2000 / XP / 7 /8/

Vista operation systems

1.2 Check list

Please make sure the following items are included with your LCD monitor;

The monitor (and the pedestal)

Lower stand

Power cord

VGA cable

DVI cable (Optional)

Documentation and software disc

Setup poster

Warranty

If any of these items are missing, please contact your dealer for technical support and custom service.

Note: Be sure to save original box and all packing materials for future transport.

Chapter II. Installation

2.1 Install the pedestal

Please follow the steps illustrated below to install the pedestal.

2.2 Connect your monitor to your computer

1. Power off and unplug your computer.

2. Connect the 15-Pin ends of the signal cable to the VGA port of your monitor and the VGA OUT jack

on the back of your computer. Secure the screws on both ends of the signal cable.

or, connect the DVI signal cable to the DVI port on the monitor and the other end of the

cable to the back of the computer or source device.

3. Connect one end of power cord to the monitor, then connect the other end of the power cords to the

nearest electrical outlet.

Warning! To reduce the risk of electric shock or damage to the equipment:

Do not disable the power cord grounding feature. The grounding plug is an

important safety feature.

Plug the power cord into an easily accessible grounded outlet.

Disconnect the power from the equipment by unplugging the power cord from

the electrical outlet.

4. Power on your computer and monitor. If your monitor displays an image, the installation has been

successfully done. If the monitor does not display any image, check all the connections.

Cautions: 1. For installation, please complete signal cord connection before plugging the power

cord into the electrical outlet to avoid damaging the monitor.

2. During installation, please support the front frame with your hand at its center of

gravity to avoid dropping and damaging the monitor. Do not touch the surface of the

LCD panel.

Pressure on the panel may cause non-uniformity of color or disorientation

of the liquid crystals. If this occurs the screen will not recover to its normal

condition.

AC DVI VGA

Overview of the ports of the monitor:

1. AC power supply input

2. DVI signal input

3. VGA signal input

2.3 Disconnect the pedestal for shipping

Press the clip button on the pedestal and remove the pedestal from the stand.

Chapter III. Monitor overview

Overview of front panel controls

Control Function

1 Menu Opens, select or exits the OSD menu

2 — Minus

If the OSD menu is on, press to navigate backward through

the OSD menu and decrease adjustment levels.

Plus/input If the OSD menu is on, press to navigate for

ward through the

OSD menu and increase adjustment levels.

If the OSD in inactive, press to activate the input button to

select the video signal input (DVl or VGA)

4 /OK Auto/OK If the OSD menu is on, press to

select the highlighted menu

items.

If the OSD menu is inactive, press to activate

the auto

adjustment feature to optimize the screen image.

Power Turns the monitor on or off

6 Power LED Blue=Fully powered.

Amber=Sleep mode.

Flashing Amber=Sleep Timer mode.

Chapter IV. Operational Instruction

4.1 Power ON/OFF Switch

Press this button to power on/off your monitor. Note: The ON/OFF switch does not disconnect

your monitor from the main voltage. To completely disconnect the main voltage, please remove

the power plug from the socket.

4.2 Power indicator

The power LED is blue when the monitor operates normally. If the monitor runs in power-saving

mode, this indicator changes to amber. When the monitor is turned off, this indicator is not lit.

4.3 Menu features

All the following features of your monitor can be accessed and adjusted by using the on screen

display (menu) system.

1. If your monitor is not powered on, press the "Power” button to turn it on.

2. Press the "Menu” button to activate the OSD menu. The OSD main menu will be displayed.

3. To view the main menu or submenu, press the “+” on the front panel of your monitor to scroll

up or the “-” to scroll down. Then press the "OK” button to select a highlighted function.

When the highlight scrolls down to the bottom of the menu, it returns to top of the menu. When

the highlight scrolls up to the top of the menu, it returns to bottom of the menu.

4. To adjust the selected option, press the “+” or “-” button.

5. Select “Save” and return. If you do not want to save the setting, select “Cancel” from the

submenu or “Exit” from the main menu.

6. Press the “Menu” button to exit from the OSD menu.

4.4 OSD operational instructions

Icon

Main menu option

Submenu option

Note

Brightness To adjust the brightness level of the

screen. The factory default range is 90.

Contrast To adjust the contrast level of the screen.

The factory default range is 80.

Color

Selects the screen color. The factory is

6500K or Custom color,

depending on the

mode.

Warm- 5000K

Changes color to slightly reddish white.

Standard- 6500K

Uses standard colors (default).

Cool- 9300K

Change color to slightly blueish white.

Custom (RGB)

Selects and adjusts your own color scales:

Red Color – sets your own red color

levels.

Green Color – sets your own green color

levels.

Blue Color – sets your own blue color

levels.

Image control

To adjust the image on the screen. The

ambient brightness sensor can also be

enabled or disabled (only applicable to

some models)

Auto-adjustment

To automatically adjust the image on the

screen (only applicable to VGA input).

Clock and Phase

To adjust the clock phase of the screen.

This adjustment eliminates all horizontal

noises to enable

clearer and more lifelike

images and

characters (only applicable to

VGA input)

Horizontal position To adjust the horizontal position of an

image (only applicable to VGA input).

Vertical position

To adjust the vertical position of an image

(only applicable to VGA input).

Custom Scaling

Selects the method on how displayed

information on the monitor will be

formatted. Select

Fill to Screen – image fills the entire

screen and may look distorted or

elongated because of non-proportional

scaling of height and width.

Fill to Aspect Ration –

image is sized to fit

the screen and maintains proportional

image.

Sharpness

Adjusts the screen image to look sharper

or soft.(range:1~6)

Dynamic Contrast Turns Dynamic Contrast Ratio On or Off.

The factory default is Off.

OSD Control Provides a menu for adjusting the

on-screen display (OSD) control.

OSD position To adjust OSD position for your monitor.

Horizontal OSD Position

To adjust the visual position of the OSD

menu to the right or left

of the screen. The

factory default horizontal position value is

97.

Vertical OSD Position

To adjust the visual position of the OSD

menu up or down the screen. The factory

default vertical position value is 13.

OSD Transparency

To adjust the transparency to enable

transparent background information under

the OSD. (range:0~7)

OSD Timeout

To set the OSD display time (in seconds)

after the last pressing the button. The

factory default setting is “30 seconds”.

Tabla de contenidos

Otros manuales de Monitor de HP

HP Essential LE1901w Manual de usuario

HP Compaq Advantage LA2306x Instrucciones de uso

HP 1332A Manual de servicio

HP L1755 Manual de usuario

HP Compaq L2311c Manual de usuario

HP EliteDisplay S240ml Instrucciones de uso

HP 2509p Manual de usuario

HP DreamColor Z Series Manual de usuario

HP HP ZR2040w Instrucciones de montaje

HP V22ve G5 Manual

HP W2338h Manual de usuario

HP V196bz Instrucciones de instalación

HP LA1905wg - Widescreen LCD Monitor Instrucciones de uso

HP L2035 Instrucciones de uso

HP Compaq L1506x Manual de usuario

HP Compaq CV5500 Manual de usuario

HP FV247AA#ABA - Compaq Presario Q1859 Cómo utilizar

HP Z24U G3 Manual

HP HP M27f Hoja de especificaciones

HP E23 G4 Manual

HP Compaq LA1951G Instrucciones de uso

HP L2035 Manual de usuario

HP vf15 Manual de usuario

HP Compaq L1702 Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación