HP E3494A Instrucciones de instalación y mantenimiento

Tabla de contenidos

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario

Installation and Service

Guide

Publication number E3494-97000

First edition, May 1996

For Safety information, Warranties, and Regulatory information, see the

pages behind the index.

© Copyright Hewlett-Packard Company 1994, 1995, 1996

All Rights Reserved

HP Processor Probe for

PowerPC 603/603e

HP processor probe—At a Glance

The HP processorprobe providesa

low-cost wayto debug embedded

softwarefor IBM/Motorola PowerPC

microprocessors.

Supported processors

Your HP processor probe is

pre-programmed for either the

PowerPC 603or PowerPC 603e

processor.

The floppydisk containsfirmware to

program your HP processor probe for

additional PowerPC processors.

Thetargetconnection

The HP processorprobe connectsto

your target microprocessor via a

special connector onthe targetsystem.

The configuration switches

Usethe switches to configure

communication to the HP 16505A. There

is a guide totheseswitches on the

bottom of the HP processor probe.

The status LEDs

LEDs show thestatus of the power

supply, the target system, and the

connection to the LAN.

Compatibility with other products

The HP processorprobe requiresthe

use ofa host basedsoftware debugger.

No debuggersfor the HP processor

probe are sold byHewlett-Packardso

you must purchase a software

debugger from a third party.

ii

iii

iv

Contents

Part 1 Installation

1 Connecting to the Host Computer

Connecting the HP processor probe to a Power Source 5

To choose a power cord 5

To connect the power cord and turn on the HP processor probe 8

Setting Up a LAN Connection 9

To obtain an IP address 10

To configure LAN parameters using the built-in terminal interface 11

To configure LAN parameters using "ipconfig700" 14

To configure LAN parameters using BOOTP 17

To set the 10BASE-T configuration switches 19

To verify LAN communications 20

Setting Up a Serial Connection 21

To set the serial configuration switches 22

To connect a serial cable 22

To verify serial communications 24

Setting up the Host Software 25

2 Connecting to the Target System

Connector provided 28

To test the HP processor probe 29

To connect to a target system via the IEEE 1149.1 (JTAG) Port 29

Part 2 Using the HP processor probe

3 Configuring the HP Processor Probe for PowerPC 603/603e

To configure the HP processor probe 38

General Configuration Items 39

v

To set restrict to real-time runs 39

Setting the JTAG Clock Speed (communications speed) 40

Configuring reset operation 41

Setting memory read delays 42

Setting memory write delays 43

Setting BNC Break In operation 44

Setting BNC trigger out operation 45

Generating parity bits on memory operations 46

Setting databus size 47

Processor Memory Cache Configuration Items 48

Enabling data retry mode 49

Configuring the memory read operation 50

Configuring data memory write operations 51

Configuring instruction memory write operations 52

Part 3 Reference

4 Designing a Target System

Target System Requirements for PowerPC 603 58

Target System Requirements for PowerPC 603e 59

Target System Requirements for other PowerPC Processors 60

Motorola MVME 160X, Ultra, Atlas and Series E Target Boards 61

PowerPC 603 JTAG Interface Connections and Resistors 62

5 Specifications and Characteristics

Processor Compatibility 66

Electrical Specifications 66

Environmental Specifications 68

Product Regulations 68

6 Updating Firmware

To update firmware using prgflash.xxx 71

To run prgflash.xxx on Unix workstations 72

To run prgflash.exe on MS-DOS 72

Contents

vi

To display current firmware version information 73

If the firmware doesn’t appear to be updated 74

If there is a power failure during a firmware update 74

7 Solving Problems

Status Lights 78

Problems with the LAN Interface 79

If you cannot verify LAN communication 79

If you have LAN connection problems 80

If the "POL" LED is lit 81

If it takes a long time to connect to the network 81

Problems with the Serial Interface 82

If you cannot verify RS-232 communication 82

If you have RS-232 connection problems with the MS Windows Terminal pro-

gram 82

Problems with the HP Processor Probe Itself 84

To run the power up self test 84

To execute the built-in performance verification test 86

Returning the HP processor probe to Hewlett-Packard for Service 92

To return the HP processor probe to Hewlett-Packard 92

To obtain replacement cables 93

Contents

vii

Contents

viii

Part 1

Installation

Installation

1

Installation

2