HP Kayak XA-s Series 02 Manual de usuario
HP Kayak XA-s 02xx PC Workstation -
Installing Accessories In Your
HP Minitower PC Workstation
Explains in detail how to install accessories, such as extra memory,
accessory boards, and additional disk drives.
M02inst.fm Page 1 Thursday, February 18, 1999 3:48 PM
HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Minitower PC
Workstation
Supported HP Accessories
2English
Supported HP Accessories
Contact your dealer for an up-to-date list of supported accessories.
Up to six accessory boards
can be installed:
- One AGP slot (graphics)
- Three 32-bit PCI slots (one used by SCSI/LAN board)
- One combination PCI or ISA slot
- One 16-bit ISA slot
Front Access Drives, for example:
- 3.5-inch 1.44 MB flexible disk drive
(one third height)
- 5.25-inch DDS tape drive (half height)
Internal Mass
Storage Devices
Pack of five pairs of rails for
Front Access Devices:
- 3.5-inch disk drives (D3566A)
- 5.25-inch disk drives (D2880A)
Main Memory Upgrades
DIMM slots for 100 MHz SDRAM:
- 32 MB Non-ECC (D6501A)
- 64 MB Non-ECC (D6502A)
- 128 MB Non-ECC (D6503A)
- 32 MB ECC (D6521A)
- 64 MB ECC (D6522A)
- 128 MB ECC (D6523A)
- 256 MB ECC (D6524A)
M02inst.fm Page 2 Thursday, February 18, 1999 3:48 PM
English 3
HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Minitower PC Workstation
Removing and Replacing the Cover
Removing and Replacing the Cover
WARNING For your safety, never remove the PC Workstation’s cover without first
removing the power cord from the power outlet, and any connection to
a telecommunications network. Always replace the cover on the
PC Workstation before switching it on again.
Removing the Cover
1Switch off the display and computer.
2Disconnect all power cables and any telecommunications cables.
3If necessary, unlock the cover using the key on the back panel, and
remove any floppy diskettes from the floppy drive.
4Push the two latches on the sides of the computer upwards.
5Grasp the cover on both sides of the computer, and carefully slide it
forwards and off the computer.
Step 4
Step 4
Step 5
M02inst.fm Page 3 Thursday, February 18, 1999 3:48 PM
HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Minitower PC
Workstation
Removing and Replacing the Cover
4English
Replacing the Cover
1Ensure that you have installed all your accessories and that all
internal cables are properly connected and safely routed.
2Ensure that the two latches on the front sides of the cover are lifted
up, and that the lock is unlocked.
3Slide the cover onto the computer, making sure that the two guides
at the bottom of the case slide into the two rails at the base of the
computer. Firmly slide the cover backwards into position.
4Lower the latches on the front sides of the cover. If required, lock
the cover using the key provided.
5Reconnect all the power cables.
Press here on both sides
of the PC’s cover.
M02inst.fm Page 4 Thursday, February 18, 1999 3:48 PM
English 5
HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Minitower PC Workstation
Removing and Replacing the Cover
Intrusion Monitor Your PC Workstation is equipped with an intrusion monitor, which is
located on the front of the PC Workstation, behind the Hardware
Control Panel. It is designed to detect whether your PC Workstation
has been opened since the last time it was used:
•If your PC Workstation has been opened, it is assumed that the
system configuration has changed and a full start-up check is carried
out.
•If your PC Workstation has not been opened, it is assumed that the
system configuration has not changed and a reduced start-up check
is carried out.
M02inst.fm Page 5 Thursday, February 18, 1999 3:48 PM
HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Minitower PC
Workstation
Moving the Power Supply
6English
Moving the Power Supply
1Disconnect the computer’s power cord and any telecommunications
cable.
2Remove the computer’s cover (see page 3).
3Remove the fan connection to the system board.
4Press the retaining buttons on each side of the HP UltraFlow airflow
guide and lift it out of the PC Workstation’s case.
5Unscrew the four self-retaining screws at the back of the power
supply.
HP UltraFlow
Airflow Guide
Retaining
button
Fan connection to
system board
Unscrew the
self-retaining screws
M02inst.fm Page 6 Thursday, February 18, 1999 3:48 PM
English 7
HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Minitower PC Workstation
Moving the Power Supply
WARNING To avoid electrical shock, do not open the power supply.
6Slide the power supply out of the computer until it stops—the
power supply unit remains connected to the computer.
Replacing the Power
Supply after Installing
Accessories
1Check that all internal cables are safely routed.
2Slide the power supply back into the computer.
3Tighten the four self-retaining screws.
4Replace the HP UltraFlow airflow guide.
5Reconnect the fan to the system board.
Slide the power
supply unit clear of
the computer
Power Supply
M02inst.fm Page 7 Thursday, February 18, 1999 3:48 PM
HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Minitower PC
Workstation
Installing Memory
8English
Installing Memory
Main Memory Modules
If you need more main memory to run your application software, you
can install up to 768 MB of memory in three DIMM slots.
Main memory upgrades are available in single 32 MB, 64 MB, 128 MB
and 256 MB Non-ECC SDRAM or 64 MB, 128 MB and 256 MB ECC
SDRAM memory modules. You should note that only 100 MHz memory
modules should be used to upgrade your PC Workstation.
CAUTION Static electricity can damage electronic components. Turn off all
equipment. Do not let your clothes touch the accessory.
To equalize the static electricity, rest the accessory bag on top of the
power supply while you are removing the accessory from the bag.
Handle the accessory as little as possible and with care.
To install a main memory module:
1Disconnect the computer’s power cord and any LAN or
telecommunications cable.
2Remove the computer’s cover (see page 3).
3Remove the fan connection to the system board.
NOTE Refer to the illustration on page 8 for steps 3 and 4.
4Press the retaining buttons on each side of the HP UltraFlow airflow
guide and lift it out of the PC Workstation’s case.
5Remove the transparent airflow guide covering the processor
sockets (if needed).
6Remove the floppy disk drive data cable from the system board.
7The location of the memory module slots is shown here.
M02inst.fm Page 8 Thursday, February 18, 1999 3:48 PM
English 9
HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Minitower PC Workstation
Installing Memory
8Slide the memory module into the slot at 90° to the system board
(with the cutouts furthest away from the processor).
9Firmly press the memory module completely into the connector
until the retaining clips click into position.
10 Repeat this procedure for each additional memory module you want
to install.
11 Install any other accessories if necessary, then replace all units and
reconnect all cables and power cords. Replace the cover (refer
to page 3).
12 Check the HP Summary Screen to verify the new configuration.
Video Adapter
Accessories Available
from Other Sources
Additional accessories, including a video MPEG module, are available
for your video adapter. However, these accessories cannot be ordered
from HP. Contact your dealer for more details about these accessories.
Slide the memory module into the slot at 90o
to the system board
Push the module until the retaining clips click
into position
Memory module
cutouts
M02inst.fm Page 9 Thursday, February 18, 1999 3:48 PM
HP Kayak XA-s 02xx PC Workstation - Installing Accessories In Your HP Minitower PC
Workstation
Installing Mass Storage Devices
10 English
Installing Mass Storage Devices
The computer has two internal shelves (for hard disk drives) and five
front-access drive shelves (for front-access drives and hard disk
drives).
Your computer is supplied with one 3.5-inch flexible disk drive and a
CD-ROM drive. If your computer is supplied with a hard disk, the hard
disk will be installed in the second internal shelf
Two internal shelves
for 3.5-inch disks
Two shelves for 3.5-inch
drives
Three shelves for 5.25-inch
drives
M02inst.fm Page 10 Thursday, February 18, 1999 3:48 PM
Otros manuales para Kayak XA-s Series 02
6
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Accesorios de HP
HP
HP Aruba UXI G Series Instrucciones de instalación
HP
HP Model 744 - VME Workstation Guía de referencia
HP
HP p1535a Manual
HP
HP L1520 - 15 Inch LCD Monitor Manual de usuario
HP
HP CC487-91209 Instrucciones de instalación y mantenimiento
HP
HP 245161-B22 - 10642 42U Rack Shock Pallet Manual de usuario
HP
HP 245161-B22 - 10642 42U Rack Shock Pallet Manual de usuario
HP
HP MPP 1.51 Manual de usuario
HP
HP E1399A Manual de usuario
HP
HP 8517B Manual de instrucciones y seguridad
HP
HP 8081A Manual de servicio
HP
HP Model 744 - VME Workstation Guía de referencia
HP
HP ProCurve 1600M Manual de usuario
HP
HP Support Anywhere Manual de usuario
HP
HP 8691B Manual de servicio
HP
HP L1520 - 15 Inch LCD Monitor Manual de usuario
HP
HP 245161-B22 - 10642 42U Rack Shock Pallet Manual de usuario
HP
HP 930C Manual de usuario
HP
HP L1510 - 15 Inch LCD Monitor Manual de usuario
HP
HP MSM415 Manual de usuario
