HP Aruba UXI G Series Instrucciones de instalación
MF877-00 Page 1
Template Revision C, 30-July-2018
Copyright 2018 Hewlett Packard Enterprise Development LP
HPE instructions for this template are available at MF877-01
Product End-of-Life Disassembly Instructions
Product Category
: Networking
Marketing Name / Model
[List multiple models if applicable.]
Aruba UXI G-Series .11ax+Eth+Cell Sensor
Purpose: The document is intended for use by end-of-life recyclers or treatment facilities. It provides the basic instructions
for the disassembly of HPE products to remove components and materials requiring selective treatment, as defined by
Directive 2012/19/EU of the European Parliament and of the Council on Waste Electrical and Electronic Equipment
(WEEE).
1.0 Items Requiring Selective Treatment
1.1 Items listed below are classified as requiring selective treatment.
1.2 Enter the quantity of items contained within the product which require selective treatment in the right column, as
applicable.
Item Description Notes
Quantity
of items
included
in product
Printed Circuit Boards (PCB) or Printed Circuit
Assemblies (PCA)
With a surface greater than 10 sq cm
1
Batteries
All types including standard alkaline and lithium
coin or button style batteries
0
Mercury-containing components
For example, mercury in lamps, display backlights,
scanner lamps, switches, batteries
0
Liquid Crystal Displays (LCD) with a surface
greater than 100 sq cm
Includes background illuminated displays with gas
discharge lamps
0
Cathode Ray Tubes (CRT)
0
Capacitors / condensers (Containing PCB/PCT)
0
Electrolytic Capacitors / Condensers measuring
greater than 2.5 cm in diameter or height
0
External electrical cables and cords
0
Gas Discharge Lamps
0
Plastics containing Brominated Flame Retardants
weighing > 25 grams (not including PCBs or PCAs
already listed as a separate item above)
0
Components and parts containing toner and ink,
including liquids, semi-liquids (gel/paste) and toner
Include the cartridges, print heads, tubes, vent
chambers, and service stations.
0
Components and waste containing asbestos
0
MF877-00 Page 2
Template Revision C, 30-July-2018
Copyright 2018 Hewlett Packard Enterprise Development LP
HPE instructions for this template are available at MF877-01
Item Description Notes
Quantity
of items
included
in product
Components, parts and materials containing
refractory ceramic fibers
0
Components, parts and materials containing
radioactive substances
0
2.0 Tools Required
List the type and size of the tools that would typically be used to disassemble the product to a point where components
and materials requiring selective treatment can be removed.
Tool Description
Tool Size (if
applicable)
Screwdriver
T8,T10,PH#1
Tweezers
3.0 Product Disassembly Process
3.1 List the basic steps that should typically be followed to remove components and materials requiring selective treatment:
1. Use screwdriver (T8) to loosen up the screw on the cover wall plate then, remove the cover wall plate.
2. Use screwdriver (T10) to loosen up 5 screws on the bottom.
3. Remove the top cover by hand and remove the light pipe.
4. Remove Antenna, PCBA, plastic cover plate, and screw using screwdriver (PH#1).
5. Use screwdriver (PH#1) to loosen up 3 screws on the antenna plate, separate Antenna and PCBA.
6. Use screwdriver (PH#1) to loosen 2 screws on the antenna, remove cable and 2 clips
7. Use Tweezers to remove shielding covers and thermal pads.
3.2 Optional Graphic. If the disassembly process is complex, insert a graphic illustration below to identify the items
contained in the product that require selective treatment (with descriptions and arrows identifying locations).
MF877-00 Page 3
Template Revision C, 30-July-2018
Copyright 2018 Hewlett Packard Enterprise Development LP
HPE instructions for this template are available at MF877-01
1. Use screwdriver (T8) to loosen up the screw on the cover wall plate then remove cover wall plate.
2. Use screwdriver (T10) to loosen up 5 screws on the bottom of product
3. Remove the top cover by hand then remove the light pipe.
MF877-00 Page 4
Template Revision C, 30-July-2018
Copyright 2018 Hewlett Packard Enterprise Development LP
HPE instructions for this template are available at MF877-01
4. Remove Antenna, PCBA, plastic cover plate, and screw using screwdriver (PH#1).
5. Use screwdriver (PH#1) to loosen up 3 screws on the antenna plate, separate Antenna and PCBA.
6. Use screwdriver (PH#1) to loosen up 6 screws on the antenna, remove cable and 2 clips
Tabla de contenidos
Otros manuales de Accesorios de HP
HP
HP 8517B Manual de instrucciones y seguridad
HP
HP L1510 - 15 Inch LCD Monitor Manual de usuario
HP
HP xp8000 - Digital Projector Cómo utilizar
HP
HP Scanjet 5370C Series Manual de usuario
HP
HP MSM415 Manual de usuario
HP
HP L1520 - 15 Inch LCD Monitor Manual de usuario
HP
HP 245161-B22 - 10642 42U Rack Shock Pallet Manual de usuario
HP
HP 930C Manual de usuario
HP
HP HSA-M001S Manual de usuario
HP
HP 8691B Manual de servicio
HP
HP Model 744 - VME Workstation Guía de referencia
HP
HP 245161-B22 - 10642 42U Rack Shock Pallet Manual de usuario
HP
HP L1520 - 15 Inch LCD Monitor Manual de usuario
HP
HP AJ765A - StorageWorks RDX Removable Disk Backup... Manual de usuario
HP
HP TPA-M002P Manual de usuario
HP
HP 8NN78AA ABB Manual de usuario
HP
HP 245161-B22 - 10642 42U Rack Shock Pallet Manual de usuario
HP
HP C8000 - Workstation - 0 MB RAM Manual de usuario
HP
HP Digital Pen 250 Manual de usuario
HP
HP C6050a Manual de usuario
