Hoymiles MI-1200 Manual de usuario

MICROINVERTER

User Manual

(Model: MI-1200 /MI-1000)

for North America

Rev 1.0

Microinverter user manual

Contact Information

Hoymiles Converter Technology Co., Ltd.

No.18 Kangjing Road, Hangzhou, Zhejiang Province, China

www.hoymiles.com

[email protected]

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, you are encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected. Consult the dealer or an experienced

radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for

compliance may void the user’s authority to operate the equipment.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device. Under Industry

Canada regulations, this radio transmitter may only operate using an antenna

of a type and maximum (or lesser) gain approved for the transmitter by

Industry Canada. To reduce potential radio interference to other users, the

antenna type and its gain should be so chosen that the equivalent isotropically

radiated power (e.i.r.p.) is not more than that necessary for successful

communication.

Microinverter user manual

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

Le pr¨|sent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.

L'exploitation est autoris¨|e aux deux conditions suivantes:

Microinverter user manual

CONTENTS

1. IMPORTANT SAFETY INFORMATION...................................4

1.1. SAFETY INSTRUCTIONS AND WARNINGS...................4

1.2. SYMBOLIC INTERPRETATION.......................................... 5

1.3. PV RAPID SHUTDOWN EQUIPMENT (PVRSE)............ 6

2. INTRODUCTION..........................................................................7

3. SYSTEM INSTALLATION.......................................................... 9

3.1. PREPARE FOR INSTALLING..............................................9

3.2. ASSEMBLY INSTRUCTION.................................................9

4. TECHNICAL DATA....................................................................14

5. INSTALLING DIAGRAM.......................................................... 19

6. INSTALLATION MAP............................................................... 20

Microinverter user manual

1. IMPORTANT SAFETY INFORMATION

1.1. SAFETY INSTRUCTIONS AND WARNINGS

Hoymiles Converter Technology Co., Ltd. (hereinafter referred to as Hoymiles)

MI-1200/ MI-1000 model microinverter (hereinafter referred to as microinverter)

is strictly designed and tested according to the national safety regulations.

However, the installation and maintenance must follow the instructions below.

Improper operation will cause serious damage to the operator and the third

party as well as property loss.

(1) Hoymiles microinverter must be installed and maintained by professionals

in accordance with local installation standards and regulations.

(2) Please read all the warnings and instructions in this manual and warning

signs on the microinverter and PV modules before installing and

maintaining the Hoymiles microinverter.

(3) The AC side grid connection must be disconnected before installing and

maintaining the microinverter.

(4) To avoid the risk of burns, do not touch the microinverter casing, the case

temperature can reach as high as 80°C.

(5) The end connector of the AC feeder must be covered with a special

waterproof cover.

(6) Ensure that the DC input voltage is less than the maximum input voltage of

the microinverter, otherwise the microinverter will be damaged, and

Hoymiles will not be responsible or warranted.

(7) Do not immerse the microinverter and connector in the liquid and expose it

to the oriented, pressurized liquid (spray, etc.,).

(8) Do not try to repair Hoymiles microinverter by yourself. If there is a

breakdown, please contact Hoymiles customer services.

WARNING - These servicing instructions are for use by qualified personnel

only. To reduce the risk of electric shock, do not perform any servicing other

Microinverter user manual

than that specified in the operating instructions.

CAUTION - To reduce the risk of fire, connect only to a circuit provided with

branch circuit overcurrent protection in accordance with the National Electrical

Code, ANSI/NFPA 70.

1.2. SYMBOLIC INTERPRETATION

1) The safety symbols used in this manual are list below and illustrated in

detail.

Symbol

Usage

Indicates a dangerous situation that can result in

deadly electric shock hazards, other serious

physical injury, or fire hazards.

Indicates directions which must be fully

understood and followed in entirety in order to

avoid potential safety hazards including equipment

damage or personal injury.

This points out that the described operation must

not be carried out. The reader should stop, use

caution and fully understand the operations

explained before proceeding.

Microinverter user manual

2) The symbols on the microinverter are list below and illustrated in detail.

Symbol

Usage

Caution

Do not come within 8 inches (20cm) of the

microinverter for any length of time while it is in

operation.

Danger of high voltages

Danger to life due to high voltage in the microinverter.

Beware of hot surface

The inverter can become hot during operation. Avoid

contact with metal surfaces during operation.

CSA mark

The inverter complies with the requirements of UL1741

and IEEE1547 standards.

Read manual first

Please read the installation manual first before

installation, operation and maintenance.

1.3. PV RAPID SHUTDOWN EQUIPMENT (PVRSE)

This product is CSA Listed as PV Rapid Shut Down Equipment and conforms

with NEC-2014 and NEC-2017 section 690.12 and C22.1-2015 Rule 64-218

Rapid Shutdown of PV Systems, for AC and DC conductors, when installed

Microinverter user manual

according to the following requirements:

Microinverters and all DC connections must be installed inside the

array boundary. Enphase further requires that the microinverters and

DC connections be installed under the PV module to avoid direct

exposure to rain, UV, and other harmful weather events.

The array boundary is defined as 305 mm (1 ft.) from the array in all

directions, or 1 m (3 ft.) form the point of entry inside a building.

This rapid shutdown system must be provided with an initiating device and (or

with) status indicator which must be installed in a location accessible to first

responders, or it must be connected to an automatic system which initiates

rapid shutdown upon the activation of a system disconnect or activation of

another type of emergency system.

The initiator shall be listed and identified as a disconnecting means that plainly

indicates whether it is in the “off” or “on” position. Examples are:

Service disconnecting means

PV system disconnecting means

Readily accessible switch or circuit breaker

The handle position of a switch or circuit breaker is suitable for use as an

indicator. Refer to NEC or CSA C22.1-2015 for more information.

2. INTRODUCTION

Hoymiles microinverter system is shown in the figure below. The whole system

consists of two parts, PV grid-connected power generation unit and PV

monitoring unit. PV grid-connected power generation units include PV modules,

microinverters, AC wiring harnesses and other system accessories; monitoring

units include DTU (data collector), remote monitoring server and other

accessories. Microinverter is the core product of PV grid-connected power

Microinverter user manual

generation unit. On one hand, it is responsible for real-time tracking the

maximum power point of the PV module, ensuring that the panels are always

working in the optimal output state; on the other hand, it efficiently converting

the input PV module DC power into the grid AC power, then delivers to the grid.

Other parts of Hoymiles microinverter system

DTU: The transfer station of the microinverter system power generation

information, through the 2.4G RF and the microinverter communication, collect

the real-time operating data of the microinverter, and transmit the collected

microinverter data to Hoymiles remote monitoring server via Ethernet.

Remote monitoring server: Collects the operating data and status of each

microinverter in the system through DTU, and provides module-level

monitoring to the user and the operation and maintenance personnel through

monitoring portal or APP to achieve remote operation and maintenance, and

improve the efficiency of operation and maintenance.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Inversor de Hoymiles

Hoymiles

Hoymiles HYT-5.0HV-EUG1 Manual de usuario

Hoymiles

Hoymiles HM-500T Manual de usuario

Hoymiles

Hoymiles MI-250 Manual de usuario

Hoymiles

Hoymiles HM-800 Manual de usuario

Hoymiles

Hoymiles MI-1000N Manual de usuario

Hoymiles

Hoymiles DTU-Pro Manual de usuario

Hoymiles

Hoymiles MI-300N Manual de usuario

Hoymiles

Hoymiles HMS-600-2T Manual de usuario

Hoymiles

Hoymiles HM-2000T-S Series Manual de usuario

Hoymiles

Hoymiles MI-1000T Manual de usuario

Hoymiles

Hoymiles MI-1000 Guía de instalación

Hoymiles

Hoymiles HM-1000NT Manual de usuario

Hoymiles

Hoymiles HMS-450-1T Manual de usuario

Hoymiles

Hoymiles MI-600NT Manual de usuario

Hoymiles

Hoymiles HMS-1600-4T-NA Manual de usuario

Hoymiles

Hoymiles HYS-3.0LV-EUG1 Manual de usuario

Hoymiles

Hoymiles HMS-2000-4T Manual de usuario

Hoymiles

Hoymiles HME-1000T-AU Manual de usuario

Hoymiles

Hoymiles HYT-5.0HV-AUG1 Manual de usuario

Hoymiles

Hoymiles HME-1500-AU Manual de usuario

Hoymiles

Hoymiles HAT-5.0HV-EUG1 Manual de usuario

Hoymiles

Hoymiles MI-1000 Manual de usuario

Hoymiles

Hoymiles MI-300 Manual de usuario

Hoymiles

Hoymiles MI-300T Manual de usuario

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario