Horiba Phosphorimeter Trigger Instrucciones de instalación y funcionamiento

Addendum: Phosphorimeter Trigger v. 1.0 (13 Aug 2003)

1

Note: All inputs are active low; all digital outputs are active low.

Warning: Do not connec

t

p

in 1 to

p

in 3.

Addendum: Phosphorimeter

Trigger

Introduction

There are two important pins to consider: Pin 5 is for the flash lamp, which provides a

12.8-µs pulse, active LOW. The acquisition delay starts on the HIGH→LOW transition

(< 10 ns jitter). Pin 4 is the phosphorimeter trigger input, which requires a minimum

pulse-width of 200 ns. Acquisition begins at 250 to 350 ns after the HIGH→LOW

transition. Any pulses received when the board is not ready for them are ignored. The

time between pulses should be at least 1 µs longer than the interval between pulses set

in the DataMax software.

Pin connections

Below is a table of connector pins and their use.

Pin # Signal I/O

1 Output opto power (5 V)

6 Disable CW xenon lamp (active LOW) O

2 Enable phosphorimeter-mirror position (active LOW) O

7 Valid phosphorimeter-mirror position (active LOW) I

3 Input opto power (5 V)

8 Status 1 (reserved for future use) I

4 Trigger phosphorimeter cycle (on HIGH→LOW transition) I

9 Status 2 (reserved for future use) I

5 Flash phosphorimeter lamp (on HIGH→LOW transition) O

Addendum: Phosphorimeter Trigger v. 1.0 (13 Aug 2003)

2

Typical circuitry

Input

A typical input circuit to the user trigger might look like this:

Output

A typical output circuit to the user trigger might look like this:

+5V (user supplied)

74HC or HCT logic

(or LS)

USER

270–470 Ω

USER

Input opto power

Data inputx

7 mA

470 Ω

SPECTRACQ USER I/O CONNECTOR

Pin 1

+5V

74FCT245

Pin 3

Data outputx

12 mA max

Output opto power

SPECTRACQ I/O USER CONNECTOR

Tabla de contenidos

Otros manuales de Instrumento de medición de horiba

horiba

horiba TW-100 Manual de usuario

horiba

horiba 9551-20D Manual de usuario

horiba

horiba 9681S-10D Manual de usuario

horiba

horiba DO Tip 7541 Manual de usuario

horiba

horiba 6377-10d Manual de usuario

horiba

horiba APMA-370 Manual de usuario

horiba

horiba B-711 Manual de usuario

horiba

horiba 9681-10D Manual de usuario

horiba

horiba ihr550 Manual del propietario

horiba

horiba 9618-10D Manual de usuario

horiba

horiba LAQUAact-PD110 Manual de usuario

horiba

horiba OPSA-150 Manual de usuario

horiba

horiba APSA-370 Manual de usuario

horiba

horiba ISFET 0040-10D Manual de usuario

horiba

horiba HP-200 Manual de usuario

horiba

horiba d-51 Manual de usuario

horiba

horiba D-73 Manual de usuario

horiba

horiba LAQUAtwin-ORP-11 Manual de usuario

horiba

horiba D-20 Series Manual de usuario

horiba

horiba IG-320 Manual de usuario

horiba

horiba LAQUAtwin-EC-11 Manual de usuario

horiba

horiba 9678-10D Manual de usuario

horiba

horiba 9615S-10D Manual de usuario

horiba

horiba LAQUA-EC1500 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario