Hoppe AUDIO MINI Manual de usuario
INSTALLATION INSTRUCTIONS / OWNER’S MANUAL:
AUDIO MINI
OFF-ROAD SOUND SYSTEM FOR HONDA TALON 1000 / TALON 1000-4
MODELS
www.hoppeindustries.com
22667 FM 15 Troup, TX 75789
(262) 552-2770
Revision - 2 of 18
Thank you for choosing the Hoppe Audio Mini off-road sound system. We hope you
enjoy the off-road sound system, and we ask that you follow these instructions very
closely. Doing so will save you time and ensure that your experience with the new Audio
Mini is a positive one.
We strongly suggest that you read the complete instructions before beginning the
installation process to eliminate the possibility of performing unnecessary work.
Having a safe and clean environment and using the proper tools is essential for a
successful installation.
It is critical that proper eye wear, ear protection, and protective clothing is worn
throughout the installation.
When you receive your Audio Mini off-road sound system, please check to ensure that all
parts and hardware are included. If there are any parts missing or if you have any
questions concerning the system at this time call Hoppe at (262)-552-2770 Mon-Thur.
Hoppe reserves the right to change specifications, equipment, or designs at any time
without notice and without incurring obligation.
Revision - 3 of 18
TABLE OF CONTENTS
SECTION 1 –Tools Required............................................................................................ 4
SECTION 2 –About your Audio Mini sound system ......................................................... 4
2.1 Applicable Year Models:.......................................................................................... 4
2.2 Audio Equipment Details:......................................................................................... 4
2.3 Warranty: .................................................................................................................. 5
2.4 Care and Maintenance: ............................................................................................. 5
2.5 Warnings:.................................................................................................................. 6
SECTION 3 –Pre-Installation Inspection ......................................................................... 7
SECTION 4 –Installation.................................................................................................. 8
Revision - 4 of 18
SECTION 1 – Tools Required
Socket wrench set
Combination wrench set
Wire cutters
In addition to the above items, you may need shop supplies such as electrical tape, wire
ties, thread locking compound, etc.
SECTION 2 – About your Audio Mini sound system
2.1 Applicable Year Models:
This Audio Mini off-road sound system is designed to fit the following Honda Talon 1000
/ Talon 1000-4 models:
2019-2021 Talon 1000 (all versions)
2020-2021 Talon 1000-4 (all versions)
All versions means it includes sub models such as X, R, Special Edition, and Fox
Live Valve.
This system is compatible with most front full windshields and roofs.
Accessories that mount overhead near the front of the roll cage such as rear view
mirrors, wiper motors, etc. may not be compatible or may require modification.
Contact Hoppe customer service for questions.
2.2 Audio Equipment Details:
Your Audio Mini off-road sound system is powered by using
their marine series audio equipment. This equipment is designed to function in all
weather conditions with an IPX6 water resistance (powerful water jet) rating. The stereo
is specifically engineered to provide excellent sound quality and volume in an open air
enviroment so you can enjoy your music on the go.
To learn more details about your stereo system, you can access product information and
manuals for the stereo equipment here:
KMC2 receiver: https://www.kicker.com/46KMC2
Speakers: https://www.kicker.com/41KM604W
You can feel free to crank up the volume without much worry of harming your system.
However, it is wise to use a little common sense. If you hear any distortion, back off a
little.
Use the equalizer settings in your KMC2 receiver to adjust the settings to your
preferences.
Revision - 5 of 18
2.3 Warranty:
Your Audio Mini comes equipped with a 1 year limited warranty covering the light, the
stereo equipment, and the fiberglass enclosure. The date of warranty coverage will be
determined by the registration date of the warranty card or online warranty registration.
http://www.motortrike.com/TrikeAccWarranty.aspx
If the warranty is not registered with Hoppe, the warranty period will begin when the
Audio Mini was shipped from Hoppe's factory.
2.4 Care and Maintenance:
Your off-road sound system does not require any maintenance other than an occasional
cleaning. To clean your audio system, simply hose off or power wash from a distance. If
needed, use a mild automotive soap and sponge or brush. Use common sense. Do not use
a high pressure power washer up close where it could cut, scar, or force water beyond the
design intent of the enclosure, light, or stereo equipment.
There is an inline fuse, close to the end of the chassis harness where it connects to the
winch power cables. It can be accessed by pulling the cap off of the fuse holder. There is
also a mini 40 amp ignition relay built into the chassis harness next to the inline fuse. See
Figure 1.
Figure 1: Fuse location.
Fuse 1: 15 amp mini fuse for light / radio receiver power.
IGNITION
RELAY
INLINE
FUSE
Revision - 6 of 18
2.5 Warnings:
This off-road system adds up to 25 lbs. to your vehicle and is located up high on the roll
cage. This increases the vehicle’s center of gravity and changes the vehicle dynamics and
handling characteristics. Use extra caution as you learn the driving characteristics of your
vehicle with your new off-road sound system installed. High speed cornering, off camber
or side hill, acceleration, and braking performance will be negatively impacted by the
weight of the sound system.
Do not listen to your stereo at an uncomfortable volume for extended periods of time.
Potential hearing loss may result.
Revision - 7 of 18
SECTION 3 – Pre-Installation Inspection
Included in your off-road sound system are the following components:
Pre-assembled Audio Mini off-road sound system (All speakers and electronics
come preinstalled with interior wire harness.)
Chassis wire harness
Mounting brackets
Hardware bag
Zip ties
If any of the parts are missing, damaged, or you have any questions concerning them,
please call Hoppe at (262)-552-2770 Mon-Thur. 8am-5pm CST.
In addition to accounting for all of the parts that you should receive with the top, you
should inspect the vehicle in the following ways.
Ensure that the vehicle is equipped with the factory roll cage, and the roll cage has
not been bent out of shape in a roll over.
Make sure the vehicle does not have any aftermarket accessories that are
incompatible with the top.
Make sure the battery is in good condition and holds a charge.
Make sure the charging system is in good condition.
Revision - 8 of 18
SECTION 4 – Installation
1. If you have a roof installed, you will need to remove the front two roof mounting
bolts for the installation of your Audio Mini. Remove the bolts shown in Figure 2,
and save them for reinstallation later. With the bolts removed, the Audio Mini
bracket will slide between the roof and roll bar.
Figure 2: Remove front bolts attaching the roof to the frame.
2. Place the provided loop clamps in the approximate mounting locations on the
outside roll bars. The Audio Mini brackets will rest on the loop clamps and be
secured in the following steps. See Figure 3.
Revision - 9 of 18
Figure 3: Approximate locations of the loop clamps.
3. Place the driver’s side bracket on top of the loop clamp and roof mounting
bracket. Verify correct orientation of the mounting bracket. See Figure 4. Note:
Driver side bracket shown. (Passenger side similar)
Figure 4: Mounting location of the Audio Mini bracket.
4. Use the supplied 3/8”-16 x 1” bolts, washers, and nylock nuts to secure the loop
clamp to the mounting bracket. Lay the roof on top of the Audio Mini bracket
FRONT
REAR
Revision - 10 of 18
(location shown in Figure 5 below) and replace both the sleeve washer and roof
mounting bolt. Snugly tighten both the loop clamp bolt and the roof mounting
bolt, waiting to fully tighten until the Audio Mini is in the final desired position.
See Figure 5.
Figure 5: Hardware for mounting the loop clamps to the brackets.
5. Repeat Steps 3 and 4 for the passenger side bracket.
6. Remove the front hood from the front of the vehicle by lifting and rotating the
lock knobs, lifting to release the 4 bosses, and sliding towards the front of the
vehicle. See Figure 6.
Figure 6: Remove the radiator hood access panel.
ROOF RESTS
HERE
Otros manuales para AUDIO MINI
8
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Hoppe
