Hoppe AUDIO MINI Guía de inicio rápido
INSTALLATION INSTRUCTIONS / OWNER’S MANUAL:
AUDIO MINI
OFF-ROAD SOUND SYSTEM FOR CFMOTO UFORCE 1000 / 1000 XL
MODELS
www.hoppeindustries.com
22667 FM 15 Troup, TX 75789
(262) 552-2770
Revision - 2 of 18
Thank you for choosing the Hoppe Audio Mini off-road sound system. We hope you
enjoy the off-road sound system, and we ask that you follow these instructions very
closely. Doing so will save you time and ensure that your experience with the new Audio
Mini is a positive one.
We strongly suggest that you read the complete instructions before beginning the
installation process to eliminate the possibility of performing unnecessary work.
Having a safe and clean environment and using the proper tools is essential for a
successful installation.
It is critical that proper eye wear, ear protection, and protective clothing is worn
throughout the top installation.
When you receive your Audio Mini off-road sound system, please check to ensure that all
parts and hardware are included. If there are any parts missing or if you have any
questions concerning the system at this time call Hoppe at (262)-552-2770 Mon-Thur.
8am-5pm CST or Friday 8am -12pm CST. Or you can email us at
Hoppe reserves the right to change specifications, equipment, or designs at any time
without notice and without incurring obligation.
Revision - 3 of 18
TABLE OF CONTENTS
SECTION 1 –Tools Required............................................................................................ 4
SECTION 2 –About your Audio Mini sound system ......................................................... 4
2.1 Applicable Year Models:.......................................................................................... 4
2.2 Audio Equipment Details:......................................................................................... 4
2.3 Warranty: .................................................................................................................. 4
2.4 Care and Maintenance: ............................................................................................. 5
2.5 Warnings:.................................................................................................................. 5
SECTION 3 –Pre-Installation Inspection ......................................................................... 6
SECTION 4 –Installation.................................................................................................. 7
Revision - 4 of 18
SECTION 1 – Tools Required
Socket wrench set
Combination wrench set
Wire cutters
In addition to the above items, you may need shop supplies such as electrical tape, wire
ties, thread locking compound, etc.
SECTION 2 – About your Audio Mini sound system
2.1 Applicable Year Models:
This Audio Mini off-road sound system is designed to fit the following UFORCE models:
2019-2022 UFORCE 1000
2022 UFORCE 1000 XL
This system is compatible with most front windshields.
Accessories that mount overhead near the front of the roll cage visor such as rear
view mirrors, wiper motors, etc. may not be compatible or may require
modification. Contact Hoppe customer service for questions.
2.2 Audio Equipment Details:
Your Audio Mini off-road sound system is powered by using
their marine series audio equipment. This equipment is designed to function in all
weather conditions with an IPX6 water resistance (powerful water jet) rating. The stereo
is specifically engineered to provide excellent sound quality and volume in an open air
enviroment so you can enjoy your music on the go.
To learn more details about your stereo system, you can access product information and
manuals for the stereo equipment here:
KMC2 receiver: https://www.kicker.com/kmc2
Speakers: https://www.kicker.com/41KM604W
You can feel free to crank up the volume without much worry of harming your system.
However, it is wise to use a little common sense. If you hear any distortion, back off a
little.
Use the equalizer settings in your KMC2 receiver to adjust the settings to your
preferences.
2.3 Warranty:
Your Audio Mini comes equipped with a 1 year limited warranty covering the light, the
stereo equipment, and the enclosure. The date of warranty coverage will be determined
by the registration date of the warranty card or online warranty registration.
Revision - 5 of 18
http://www.motortrike.com/TrikeAccWarranty.aspx
If the warranty is not registered with Hoppe, the warranty period will begin when the
Audio Mini was shipped from Hoppe's factory.
2.4 Care and Maintenance:
Your off-road sound system does not require any maintenance other than an occasional
cleaning. To clean your audio system, simply hose off or power wash from a distance. If
needed, use a mild automotive soap and sponge or brush. Use common sense. Do not use
a high pressure power washer up close where it could cut, scar, or force water beyond the
design intent of the enclosure, light, or stereo equipment.
There is an inline fuse, close to the end of the chassis harness where it connects to the
winch contactor. It can be accessed by pulling the cap off of the fuse holder. There is also
a mini 40-amp ignition relay built into the chassis harness next to the inline fuse. See
Figure 1.
Figure 1: Fuse location.
Fuse 1: 15 amp mini fuse for light / radio receiver power.
2.5 Warnings:
This off-road system adds up to 25 lbs. to your vehicle and is located up high on the roll
cage. This increases the vehicle’s center of gravity and changes the vehicle dynamics and
handling characteristics. Use extra caution as you learn the driving characteristics of your
vehicle with your new off-road sound system installed. High speed cornering, off camber
or side hill, acceleration, and braking performance will be negatively impacted by the
weight of the sound system.
Do not listen to your stereo at an uncomfortable volume for extended periods of time.
Potential hearing loss may result.
IGNITION
RELAY
INLINE
FUSE
Revision - 6 of 18
SECTION 3 – Pre-Installation Inspection
Included in your off-road sound system are the following components:
Pre-assembled Audio Mini off-road sound system (All speakers and electronics
come preinstalled with interior wire harness.)
Chassis wire harness
Mounting brackets
Hardware bag
Zip ties
Zip tie mounts
Alcohol wipes
If any of the parts are missing, damaged, or you have any questions concerning them,
please call Hoppe at (262)-552-2770 Mon-Thur. 8am-5pm CST.
In addition to accounting for all of the parts that you should receive with the top, you
should inspect the vehicle in the following ways.
Ensure that the vehicle is equipped with the factory roll cage, and the roll cage has
not been bent out of shape in a roll over.
Make sure the vehicle does not have any aftermarket accessories that are
incompatible with the top.
Make sure the battery is in good condition and holds a charge.
Make sure the charging system is in good condition.
Revision - 7 of 18
SECTION 4 – Installation
1. Remove the four factory bolts securing the roof to the visor. Save the hardware
for reinstallation in later steps. See Figure 2.
Figure 2: Remove the front bolts securing the roof to the visor.
2. Remove the factory bolts from the front visor as indicated in Figure 3. The bolts
will be replaced. Note: Driver side shown. (Passenger side similar)
Figure 3: Remove the factory front visor bolts.
Revision - 8 of 18
3. Place the driver’s side bracket between the roll cage and front visor. Use the
supplied M8 x 20 mm bolts and washers to snugly tighten the bracket until it is
fully secured in the following steps. Verify correct orientation of the mounting
bracket. See Figure 4. Note: Driver side shown. (Passenger side similar)
Figure 4: Mounting location of the Audio Mini bracket.
4. Reusing the factory bolts, reinstall only the two center bolts securing the roof to
the visor. See Figure 5.
Figure 5: Reinstall the two center bolts securing the roof to the visor.
Revision - 9 of 18
5. Using an assistant, hang the Audio Mini off-road sound system on the brackets
using the supplied ¼”-20 bolts and washers (snugly tightened). Note: The sound
system weighs up to 25 lbs. Since you will have to lift and bolt each end, it is
helpful to have an assistant for this step. See Figure 6 and Figure 7.
Figure 6: Install the ¼”-20 bolts and washers to mount the Audio Mini to the brackets.
Figure 7: Loosely install the sound system on the mounting brackets.
6. Once you have the Audio Mini in your desired position, gently lift the roof to
tighten all 4 visor bolts. Torque the bolts to 26 ft.-lbs. See Figure 4.
7. Tighten the 4 mounting bracket bolts after achieving the desired viewing position
relative to the visor. Slots in the brackets allow for adjustability to achieve your
desired viewing position. See Figure 8.
Revision - 10 of 18
Figure 8: Up-down adjustability of the Audio Mini.
8. Reusing the factory bolts, install the two bolts through the Audio Mini brackets
and visor into the roof. Tighten both bolts to secure the brackets to the visor and
roof. See Figure 9. Note: Driver side shown. (Passenger side similar)
Figure 9: Install the bolts to secure the brackets and visor to the roof.
Otros manuales para AUDIO MINI
8
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Hoppe
