Honeywell T7560A Manual de usuario

® U.S. Registered Trademark

T7560A,B,C Digital Wall Module

HONEYWELL EXCEL 5000 OPEN SYSTEM

SPECIFICATION DATA

GENERAL

The T7560A,B Digital Wall Modules (DWM) display and

provide space temperature, setpoint, Occupied/Unoccupied

override, and fan mode/speed selection for the Honeywell

Excel 10 W7750, W7751H (see also Table 5,) W7752,

W7753, W7754, W7761, W7762, W7763, and Excel 800,

600, 500, 100, 50, 20 Controllers, as applicable. A software

module ModAL is available to adapt the wall module to the

respective Excel 20, 50, 100, 500, 600, 800 controller. See

T7560A,B,C Installation Instructions (product literature no.:

EN1B-0146GE51) for details.

Using the three buttons, the user can change room

temperature setpoint, fan mode/speed, initiate/cancel bypass,

and change configuration information such as the DWM’s

engineering units.

The T7560C Digital Wall Module (see inset above) has no

user interface (e.g. LCD, buttons, or setpoint dial) and issues

only temperature and humidity values.

These wall modules are not compatible with Honeywell

W7751A,C,E,G (VAV1) and W7752D1 (FCU1) Controllers.

FEATURES

•Fully compatible with all current Excel 10 and Excel

20 to 800 controllers.

•Low power consumption.

•Integral 20kΩNTC sensor.

•Separate mounting base for easy installation.

•Tamper-resistant locking cover.

•IP30 housing.

•T7560A and B, only:

- LCD display continuously shows current space

temperature, occupied/unoccupied/standby mode,

fan status/mode, humidity, as configured.

- Push-button interface for full navigation and

change control of wall module functions.

- Single-touch occupied/unoccupied override.

- Setpoint dial for setpoint adjustment.

- Fan Speed/Mode commandable from buttons.

- Selectable °F/°C temperature display.

- Selectable setpoint type, absolute or relative.

For latest prices and delivery to your door visit MyTub Ltd - 0845 303 8383 - www.mytub.co.uk - [email protected]

T7560A,B,C DIGITAL WALL MODULES

EN0B-0237GE51 R0509 2

SPECIFICATIONS

Models

Table 1. Types of DWM

sensor1colors

(dial / housing)

pre-conf.

units

T7560A1000 Tmp blue/white °C

T7560A1026 Tmp white/white °C

T7560A1018 Tmp white/white °F

T7560A1042* Tmp white/white °F

T7560B1008 Tmp/Hum blue/white °C

T7560B1024 Tmp/Hum white/white °C

T7560B1016 Tmp/Hum white/white °F

T7560B1032* Tmp/Hum white/white °F

T7560C1006 Tmp/Hum blue/white n.a.

1 Tmp = Temperature sensor; Hum = Humidity sensor

*U.S. versions with mounting base.

Temperature Sensor Accuracy

The DWM is furnished with a 20kΩNTC temperature sensor

that follows a specific temperature-resistance curve. See Fig.

1. Honeywell controllers used with the DWM employ an

algorithm providing readings close to the actual temperature.

Table 2 summarizes the DWM sensor accuracy for normal

operating temperatures. Across the range of 43 to 104°F (6 to

40°C), the accuracy is better than ±0.75°F (±0.42°C).

80 K

70 K

60 K

50 K

40 K

30 K

20 K

10 K

010 20 30 40

40 50 60 70 80 90 100 110 °

°C

temperature (degrees)

elec

ical

ance (

)

Fig. 1. Temperature vs. resistance for 20kΩsensor

Table 2. Temperature sensor accuracy

ambient tem. (°C) max. error (°C) nominal re-

sistance (Ω)

15.5 ±0.29 31543

18.3 ±0.27 27511

21.1 ±0.27 24047

26.7 ±0.27 18490

29.5 ±0.29 16264

Humidity Sensor

Table 3. Humidity sensor specifications

parameter value

humidity sensing range 10…95% r.h.

output signal 1…10 Vdc (10…100% r.h.)

accuracy ±5% (full-scale)

Fan Speed Button (T7560A,B, only)

Table 4. Switch position and fan behavior

switch position fan behavior

auto runs as scheduled

0 OFF

1 runs at speed 1

2 runs at speed 2

3 runs at speed 3

bypass activated unchanged

NOTE: If connected to Excel 10 UV Controller W7753, fan

output will not be shorted to ground on pressing the

BYPASS button; with every other Excel 10

Controller, it will be shorted.

See T7560A,B,C Installation Instructions (product

literature no.: EN1B-0146GE51) for configuration.

Power Supply

24 Vac/dc with a valid range of 18...30 V

5 Vdc via LED input with a valid range of 5...15 V

See T7560A,B,C Installation Instructions (product literature

no.: EN1B-0146GE51) for details.

Power Consumption

<0.2 VA at 24 Vac, 50/60 Hz

DWM Setpoint Adjustment

The setpoint accuracy is ± 0.3 K (± 0.54 °F).

For latest prices and delivery to your door visit MyTub Ltd - 0845 303 8383 - www.mytub.co.uk - [email protected]

T7560A,B,C DIGITAL WALL MODULES

3 EN0B-0237GE51 R0509

Field Wiring

•16 to 22 AWG (1.5 to 0.34 mm2) depending on

application.

•18 AWG (1.0 mm2) min. for 24 Vac power wiring.

•Max. length of wire from a device to a wall module is

164 ft (50 m).

•Twisted pair wire recommended for wire runs longer than

100 ft (30.5 m).

Setpoint Adjustment Range (A and B)

Setpoint can be configured for

•Fahrenheit absolute (55...85 °F)

•Fahrenheit relative (±10)

•Celsius absolute (12...30 °C)

•Celsius relative (±5)

Temperature Value Display Resolution (A and B)

Degree Celsius ⇒0.1 °C

Degree Fahrenheit ⇒0.1 °F

Setpoint Value Display Resolution (A and B)

Degree Celsius ⇒0.5 °C

Degree Fahrenheit ⇒1.0 °F

Mounting Options

Wall mounting

Dimensions (H/W/D)

4-1/8 x 3-15/16 x 1-3/16 in. (104 x 99 x 30 mm)

Environmental Ratings

Shipping temperature: -22...+140 °F (-30...60 °C)

Operating temperature: 32...104 °F (0...+40 °C)

Relative humidity: 5...95% non-condensing

Measurement range: +6…+40 °C

Approval Bodies

UL 916, NEC Class 2

For latest prices and delivery to your door visit MyTub Ltd - 0845 303 8383 - www.mytub.co.uk - [email protected]

T7560A,B,C DIGITAL WALL MODULES

EN0B-0237GE51 R0509 4

OPERATION OF THE DWM

Table 5. Supported DWM functions with Excel 10 Controllers

bypass unit enable fan override setpt. humidity room temp. controller SW

requirements*

CVAHU W7750 3N/A N/A

333--

VAV W7751H 3N/A N/A

3N/A 31.02.15

FCU W7752 3333N/A 31.00.04

UV W7753 333333--

RIO W7761 N/A N/A N/A N/A

33--

FCU W7754 3333N/A 31.00.02

HYD W7762 3N/A N/A

3N/A 31.00.03

CHC W7763 3N/A N/A

3331.00.03

*Minimum software version which the Excel 10 controllers must have in order for them to be able to provide, via terminal 5 of the

respective wall module, a) power and b) additional information on the controller’s status for display in the LCD.

General

The T7560A and T7560B feature three buttons, a setpoint

dial, and the LCD display (see Fig. 2). This section describes

the functions of these elements. Table 5 shows the functions

available with the different Excel 10 Controllers.

Fig. 2. Control elements of DWM.

NOTE: If not specified differently, the graphics given below

show example display settings; depending on

configuration, the actual indications may vary from

those shown hereinafter.

Set Temperature

Depending on the configuration, you can adjust the

temperature within the limits given below:

°C absolute ⇒12 to 30°C (in 0.5 steps)

°C relative ⇒-5 to +5 (in 0.5 steps)

°F absolute ⇒55 to 85°F (in 1.0 steps)

°F relative ⇒-10 to +10 (in 1.0 steps)

Turn the SETPOINT DIAL

up/down to decrease/increase

the room temperature setpoint.

The display toggles the setpoint

value (either relative or absolute,

as configured).

After the new setpoint has been

set, the display returns to normal

mode after approx. 5 sec.

Set Fan Speed

The manually set fan speed is represented by a bargraph.

Depending on configuration, the fan speed can be set as

follows:

Three-speed fan override ⇒AUTO, OFF, 1, 2, 3

Two-speed fan override ⇒AUTO, OFF, 1, 2

Fan mode override ⇒AUTO, OFF, ON

NOTE: The default setting after power-up is AUTO. The

manually set fan speed overrides the controller’s

control algorithm.

Three-speed fan override

Press the FAN OVERRIDE button to toggle between:

AUTO

(fan speed from controller)

MANU OFF

(fan off)

With this setting, depending on

configuration, the display may

also read:

Humidity Display

The T7560B is capable of displaying the relative humidity. To

display the relative humidity, it must be configured in mode

P2:3. The relative humidity (in %, together with the cor-

responding letters "rh") and the room temperature will then be

displayed, alternating every 5 seconds.

Humidity mode

(e.g. 25% relative humidity)

Set Bypass/Occupancy Mode Display

The bypass function can be used to override the control

algorithm generated by the controller (e.g. for an event after

normal office hours, or for a room known to be unused).

The status of the occupancy mode can be seen from the sun,

moon, and snowflake symbols. The following LCD behaviors

are possible, depending on configuration. See T7560A,B,C

Installation Instructions (product literature no.: EN1B-

0146GE51) for configuration options:

Occupancy mode display for Excel 10 LCD signaling

(Excel 10 set to LCD_DISPLAY; with FCU, HYD, and

CHC, only.)

Effective Occupancy or Bypass mode

(SUN continuously ON)

Effective Standby mode; generated by

time program

(HALF-SUN continuously ON)

Effective Unoccupancy mode

(MOON continuously ON)

Unit Off, No Frost Protection

(OFF without snowflake)

Unit Off, With Frost Protection

(OFF WITH SNOWFLAKE)

Override Standby mode (from

central)

(HALF-SUN FLASHING)

Wink mode (NEURON©ID sent)

(SUN/MOON/SNOWFL. FLASHING)

(Only with FCU, HYD, CHC)

Press the BYPASS button to set the desired mode:

•To activate Override Occupancy or Bypass mode,

press and release the BYPASS button.

•To activate Override Unoccupancy mode, press

and hold the BYPASS button for at least 5 sec.

•To return to normal mode, press and release the

BYPASS button again.

NOTE: Pressing the BYPASS button for more than 5

seconds sends the NEURON©ID of the connected

Excel 10 controller via the LONWORKS©network.

Override Occupancy or Bypass mode

(SUN FLASHING)

Override Unoccupancy mode

(MOON FLASHING)

Override mode display for Excel 10 LED signaling (Excel

10 set to LED_OVERRIDE)

Off Conditions, No Override, Overr.

Occupancy, Overr. Standby (NO

SYMBOLS)

Wink mode (NEURON©ID sent)

(SUN/MOON/SNOWFL. FLASHING)

(Only with FCU, HYD, CHC)

Press the BYPASS button to set the desired mode:

•To activate Override Bypass mode, press and release

the BYPASS button.

•To activate Override Unoccupancy mode, press and hold

BYPASS button for at least 5 sec.

•To return to normal mode, press and release the

BYPASS button again.

NOTE: Pressing the BYPASS button for more than 5

seconds sends the NEURON©ID of the connected

Excel 10 controller via the LONWORKS©network.

Override Bypass mode

(SUN FLASHING)

AUTO

MANU

For latest prices and delivery to your door visit MyTub Ltd - 0845 303 8383 - www.mytub.co.uk - [email protected]

T7560A,B,C DIGITAL WALL MODULES

Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Rolle, Z.A. La Pièce 16, Switzerland by its Authorized Representative:

Automation and Control Solutions

Honeywell GmbH

Böblinger Strasse 17

71101 Schönaich, Germany

Phone: (49) 7031 63701

Fax: (49) 7031 637493

http://ecc.emea.honeywell.com

Subject to change without notice. Printed in Germany

EN0B-0237GE51 R0509 (74-3083)

Override Unoccupancy mode

(MOON FLASHING)

Occupancy mode display for Excel 10 LED signaling

(Excel 10 set to LED_OCCUPANCY)

Effective Bypass mode

(SUN continuously ON)

Effective Standby mode; generated by

time program

(HALF-SUN continuously ON)

Off Conditions, Effective Unoccupancy

mode

(MOON continuously ON)

Wink mode (NEURON©ID sent)

(SUN/MOON/SNOWFL. FLASHING)

(Only with FCU, HYD, CHC)

Occupancy mode display for Excel 20 to 600

Display of the currently active Excel 20 to 600 mode; further

options depend on the configuration of the controller:

Occupancy mode

(SUN continuously ON)

Standby mode; generated by time

program

(HALF-SUN continuously ON)

Unoccupancy mode

(MOON continuously ON)

To adapt the T7560 to the CARE control strategies for Excel

20 to 600, a standard ModAL software module is available.

Contact your local Honeywell distributor, or refer to

T7560A,B,C Installation Instructions (product literature no.:

EN1B-0146GE51) for further details.

ACCESSORIES

For mounting the following accessories, please refer to the

T7560A,B,C Installation Instructions (product literature no.:

EN1B-0146GE51).

T7460-LONJACK

The T7460-LONJACK is a small board and allows easy

access to LONWORKS via the wall module (the wall module

must be already connected, in compliance with the max.

cable lengths set forth by the LONWORKS Guidelines, to the

LONWORKS network via a LONWORKS bus cable). Via an

additional 3.5 mm jack plug on the board, a PC connection

can be established.

Order quantity: set of 5 pieces

T7560 Blinds

Same material and color as housing; for covering non-

operational buttons.

Order quantity: set of 50 pieces.

For latest prices and delivery to your door visit MyTub Ltd - 0845 303 8383 - www.mytub.co.uk - [email protected]

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termostato de Honeywell

Honeywell

Honeywell TheraPro HR90 Manual de usuario

Honeywell

Honeywell RTH7000 Manual de usuario

Honeywell

Honeywell TL8100 Manual de usuario

Honeywell

Honeywell PB112C-GA Manual de usuario

Honeywell

Honeywell RTH6500WF Wi-Fi Series Manual de usuario

Honeywell

Honeywell VisionPRO 8000 Manual de usuario

Honeywell

Honeywell T11A Instrucciones de montaje

Honeywell

Honeywell CT410A Manual de usuario

Honeywell

Honeywell RTH7400 series Manual de usuario

Honeywell

Honeywell PRO TH2000 Series Manual de usuario

Honeywell

Honeywell T8621A Manual de usuario

Honeywell

Honeywell PRESTIGE THX9321 Guía del usuario

Honeywell

Honeywell CT30 Series Manual de usuario

Honeywell

Honeywell RTH2310 Manual de usuario

Honeywell

Honeywell Powerpile TS86A Manual de usuario

Honeywell

Honeywell Chronotherm IV T8611G Manual de usuario

Honeywell

Honeywell T87F Manual de usuario

Honeywell

Honeywell RTH2300 series Manual de usuario

Honeywell

Honeywell C7189R2002-2 Manual de usuario

Honeywell

Honeywell TB7200 Series Manual de uso y cuidado

Honeywell

Honeywell RTHL2510 series Manual de usuario

Honeywell

Honeywell RTH7460D1018/E 5-1-1 Manual de usuario

Honeywell

Honeywell RTH9600WF Manual de usuario

Honeywell

Honeywell Lyric T6 Pro Wi-Fi Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Aube Technologies

Aube Technologies TH305 Manual de usuario

Powtier Controls

Powtier Controls 505MST Manual de usuario

Kanmor

Kanmor Zone Control 369e Manual de usuario