Honeywell RTH3100C Manual de usuario

Owner’s Manual

Read and save these

instructions.

For help please visit

yourhome.honeywell.com

RTH3100C

Non-Programmable

Digital Thermostat

Installation is Easy

1. Label wires and remove your old thermostat

2. Install and wire your new thermostat

3. Set your new thermostat to match your heating/cooling system

Do you need assistance? We are here to help.

Call 1-800-468-1502 for wiring assistance before returning

the thermostat to the store.

For use with Heat Pump Systems ONLY.

M28333

NOTICE: To avoid possible compressor damage, do not run air

conditioner if the outside temperature drops below 50°F (10°C).

ATTENTION: MERCURY RECYCLING NOTICE

This product does not contain mercury. However,

this product may replace a product that contains

mercury. Mercury and products containing

mercury should not be discarded in household

trash.

For more information on how and where to

properly recycle a thermostat containing

mercury in the United States, please refer to the

Thermostat Recycling Corporation at

www.thermostat-recycle.org.

For mercury thermostat recycling in Canada,

please refer to Switch the Stat at

www.switchthestat.ca

NO MERCUR

NO BOTE

MERCURIO

Customer assistance

For assistance with this product, please visit

http://yourhome.honeywell.com.

Or call Honeywell Customer Care toll-free at

1-800-468-1502.

To save time, please note your model number

and date code before calling.

Pull at bottom to remove thermostat from

wallplate.

Turn thermostat over to find model number

and date code.

® U.S. Registered Trademark. Patents pending.

M28331

Installation

Installation............................................3

System Setup.......................................8

About your new thermostat

Controls................................................9

Home screen quick reference ............10

Programming and operation

Compressor protection.......................10

Replace batteries ...............................11

Accessories/replacement parts..........11

Appendices

Troubleshooting..................................12

Limited warranty.................................13

Table of contents

1 Turn Off Power to Heating/Cooling System

M31535

Circuit breaker

box Heating/cooling system

power switch

Do not remove wallplate yet

3 Label Wires with Tags

Label the wires using the supplied wire labels as you disconnect them. If any

wires are not attached to terminals in your old thermostat, do not connect them

to your new thermostat.

Wrap the bare metal ends of each unused wire with electrical tape, so it cannot

touch and short out other wires.

Wire Labels

M28100

MCR33823

Terminal

designation

If you have an older thermostat with a

sealed mercury tube, turn to page 2

for proper disposal instructions.

Terminal designation

MCR31537

2 Remove Old Thermostat

Remove old thermostat but leave wallplate with wires attached.

4 Separate Wallplate from

New Thermostat

Remove wallplate from the new thermostat

and mount onto wall.

Wallplate

5 Mount Wallplate

Mount the new wallplate using the included screws and anchors.

Drill 3/16-in. holes for drywall

Drill 3/32-in. holes for plaster

6 Connect Wires

1. Match each labeled wire with same letter on terminal.

2. Use a screwdriver to loosen screw terminals, insert wires, then tighten screws.

3. Push any excess wire back into the wall opening.

If labels do not match letters on the thermostat, check “Alternate Wiring” on page

6and connect to terminal as shown (see notes, below).

We are here to help. Call 1-800-468-1502 for wiring assistance.

Alternate Wiring

If the old thermostat had both Vand VR wires, contact a heating/cooling

contractor for help.

If the old thermostat had both Oand Bwires, attach the Bwire to the C

terminal. If another wire is attached to the Cterminal, call 1-800-468-1502

for help.

If the old thermostat had W1, W2 and Ywires, contact a heating/cooling

contractor for help.

If no wire matches the Eterminal on the new thermostat, use a small

piece of wire to connect terminals Eand Aux.

Aux YGOL

RBC

Aux YGOLRBCE

43321 2 2

7 Install Batteries

Install two AA alkaline batteries.

Back of thermostat

8 Install Thermostat onto

Wallplate

Install thermostat onto the wallplate on

the wall.

9 Turn Power Back On

Turn the power back on to

the heating/cooling system.

M31544

Circuit breaker box Heating/cooling system

power switch

System Setup

Enter System Setup

Next, you must set the thermostat to control the heating and cooling system in

your home. To enter system setup, press and hold both the sand tbuttons

until the display changes (approximately 5 seconds).

Changing Settings

1. Press tto change the setting.

2. Press sto advance to the next function.

3. Press and hold sand t to exit and save settings.

Function

Description

Press the tbutton to Setting

6 select your auxiliary heating

system and optimize its

operation

3 Heat pump

8 select your emergency heating

system and optimize its

operation

9 Electric furnace: Use this setting if you have any type of

electric heating system.

14 select Fahrenheit or Celsius

temperature display

0 Fahrenheit temperature display (°F)

1 Celsius temperature display (°C)

Setup

Function

Setting

About your new thermostat

Your new Honeywell thermostat has been designed to give you many years of

reliable service and easy-to-use, push-button climate control.

• One-touch temperature controls

• Large, clear backlit display is easy to read, even in the dark

• Switchable fan control (auto or continuous fan)

• Displays both room temperature and temperature setting

• Built-in compressor protection

Thermostat controls

M28327

Digital display

screen Temperature

adjustment

Press the up or down

buttons until you

reach the desired

temperature.

NOTE: Make sure the

SYSTEM switch is set to

the system you want to

control (Heat or Cool).

Fan Switch is used to

control your fan.

In “Auto” mode, the fan

runs only when the heating

or cooling system is on.

If set to “On,” the fan runs

continuously.

System Switch is used to control your

heating or cooling system.

• Cool: Cooling system control.

• Off: All systems off.

• Heat: Heating system control.

• Em Heat: Emergency & Auxiliary Heat

control. Compressor is locked out.

Heat On

Set ToInside

Replace Batt

M28328

Low battery

warning

(see page 11)

Current inside temperature Temperature setting

System status

Cool on: Cooling system is on.

Heat on: Heating system is on.

Em: Emergency heat is on.

Aux: Auxiliary heat is on.

When Cool On/Heat On is flashing, compressor protection is engaged (see

page 10).

Display screen

Built-in compressor protection

This feature helps prevent damage to

the compressor in your air conditioning

or heat pump system.

Damage can occur if the compressor is

restarted too soon after shutdown. This

feature forces the compressor to wait 5

minutes before restarting.

During the wait time, the display will

flash the message Cool On or Heat On.

When the safe wait time has elapsed,

the message stops flashing and the

compressor turns on.

Cool On

Set ToInside

M28330

Otros manuales para RTH3100C

Tabla de contenidos

Idiomas:

Otros manuales de Termostato de Honeywell

Honeywell

Honeywell Chronotherm IV T8600D Manual de usuario

Honeywell

Honeywell VFD CORE Manual de usuario

Honeywell

Honeywell T7351 Manual de usuario

Honeywell

Honeywell RTH1120 Manual de usuario

Honeywell

Honeywell RTH2510 Series Manual de usuario

Honeywell

Honeywell Y6630D1007 Manual del propietario

Honeywell

Honeywell T8011F Manual de usuario

Honeywell

Honeywell T8611 Manual de usuario

Honeywell

Honeywell Chronotherm IV T8602C Manual de usuario

Honeywell

Honeywell T8611C Manual de usuario

Honeywell

Honeywell CT31 Manual de usuario

Honeywell

Honeywell T8112C Manual de usuario

Honeywell

Honeywell T8034C Manual de usuario

Honeywell

Honeywell Digital Round T8775A Manual de usuario

Honeywell

Honeywell RTH5100B1009 Manual de usuario

Honeywell

Honeywell T8002 Manual de usuario

Honeywell

Honeywell Single Stage Heat Pump ProgrammableCommercial... Manual de usuario

Honeywell

Honeywell TRADELINE T4798S Manual de usuario

Honeywell

Honeywell FocusPRO TH5000 Series Manual de usuario

Honeywell

Honeywell 8161 Manual de usuario

Honeywell

Honeywell RTH8500 Series Manual de usuario

Honeywell

Honeywell TH8320R1003 Manual de usuario

Honeywell

Honeywell T8611G Chmnothern IV Manual de usuario

Honeywell

Honeywell INTELLIGUARD 9000 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Aube Technologies

Aube Technologies TH305 Manual de usuario

Powtier Controls

Powtier Controls 505MST Manual de usuario

Kanmor

Kanmor Zone Control 369e Manual de usuario