Honeywell PRO TH3110B Manual de usuario

Installation

Guide

TH3110B

Non-programmable Digital Thermostat

PRO TH3110B Non-programmable Digital Thermostat

Product Application

This thermostat provides electronic control of 24 VAC single-stage heating and cool-

ing systems, or 750 mV heating systems.

System Types

• Gas, oil, or electric heat with air

conditioning

• Warm air, hot water, high-efficiency

furnaces, heat pumps, steam, gravi-

• Heat only

• Heat only with fan

• Cool only

• 750 mV heating systems

Power Type

• AA alkaline batteries (2)

System Settings

• Heat, Off, Cool

Fan Settings

• Auto, On

Must be installed by a trained, experienced technician

• Read these instructions carefully. Failure to follow these instructions can dam-

age the product or cause a hazardous condition.

• Check the ratings in this booklet to verify that this product is suitable for your

application (see page 12).

• Always test for proper operation after installation (see pages 8-9).

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before

beginning installation.

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

Install the thermostat about 5 feet (1.5m) above the floor in an area

with good air circulation at average temperature.

Do not install in locations where the thermostat can be affected by:

• Drafts or dead spots behind doors and in corners

• Hot or cold air from ducts

• Sunlight or radiant heat from appliances

• Concealed pipes or chimneys

• Unheated/uncooled areas such as an outside wall behind the thermostat

NO NO

® U.S. Registered Trademark. Patents pending.

IInnssttaallllaattiioonn

Pre-installation checklist ................2

Wallplate installation ......................3

Wiring..............................................4

Wiring diagrams ..............................5

IInnssttaalllleerrSSeettuupp

Fan operation settings ....................6

Battery installation ..........................7

Thermostat mounting ....................7

Installer setup..................................8

Installer system test ........................9

AAppppeennddiicceess

Quick reference to controls..........10

Quick reference to display............10

Compressor protection ................10

In case of difficulty ......................11

Accessories....................................12

Specifications ................................12

Table of contents

Installation tips

PRO TH3110B Non-programmable Digital Thermostat

Product Application

This thermostat provides electronic control of 24 VAC single-stage heating and cool-

ing systems, or 750 mV heating systems.

System Types

• Gas, oil, or electric heat with air

conditioning

• Warm air, hot water, high-efficiency

furnaces, heat pumps, steam, gravi-

• Heat only

• Heat only with fan

• Cool only

• 750 mV heating systems

Power Type

• AA alkaline batteries (2)

System Settings

• Heat, Off, Cool

Fan Settings

• Auto, On

Must be installed by a trained, experienced technician

• Read these instructions carefully. Failure to follow these instructions can dam-

age the product or cause a hazardous condition.

• Check the ratings in this booklet to verify that this product is suitable for your

application (see page 12).

• Always test for proper operation after installation (see pages 8-9).

CAUTION: ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before

beginning installation.

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

Install the thermostat about 5 feet (1.5m) above the floor in an area

with good air circulation at average temperature.

Do not install in locations where the thermostat can be affected by:

• Drafts or dead spots behind doors and in corners

• Hot or cold air from ducts

• Sunlight or radiant heat from appliances

• Concealed pipes or chimneys

• Unheated/uncooled areas such as an outside wall behind the thermostat

NO NO

® U.S. Registered Trademark. Patents pending.

IInnssttaallllaattiioonn

Pre-installation checklist ................2

Wallplate installation ......................3

Wiring..............................................4

Wiring diagrams ..............................5

IInnssttaalllleerrSSeettuupp

Fan operation settings ....................6

Battery installation ..........................7

Thermostat mounting ....................7

Installer setup..................................8

Installer system test ........................9

AAppppeennddiicceess

Quick reference to controls..........10

Quick reference to display............10

Compressor protection ................10

In case of difficulty ......................11

Accessories....................................12

Specifications ................................12

Table of contents

Installation tips

PRO TH3110B Non-programmable Digital Thermostat

Installation Guide

Pre-installation checklist

Package contents

Check to make sure your package includes the following items:

Operating manual

Wall anchors and

mounting screws

(2 each)

AA alkaline

batteries (2)

PRO TH3110B

digital thermostat

(wallplate attached to back)

Required tools & supplies

• No. 2 Phillips screwdriver

• Small pocket screwdriver

• Drill

• Drill bit (3/16” for drywall, 7/32” for plaster)

• Hammer

• Pencil

• Electrical tape

• Level (optional)

Remove the wallplate from the ther-

mostat as shown at left, then follow

directions below for mounting.

1 Pull wires through wire hole.

2 Position wallplate on wall, level and

mark hole positions with pencil.

3 Drill holes at marked positions as

shown below, then tap in

supplied wall anchors.

4 Place wallplate over anchors, insert

and tighten mounting screws.

Grasp top and bottom of wallplate

and pull to remove from thermostat.

Drill 3/16” holes for drywall.

Drill 7/32” holes for plaster.

Wall anchors

Mounting screwsWire hole

Wallplate installation

PRO TH3110B Non-programmable Digital Thermostat

Installation Guide

Pre-installation checklist

Package contents

Check to make sure your package includes the following items:

Operating manual

Wall anchors and

mounting screws

(2 each)

AA alkaline

batteries (2)

PRO TH3110B

digital thermostat

(wallplate attached to back)

Required tools & supplies

• No. 2 Phillips screwdriver

• Small pocket screwdriver

• Drill

• Drill bit (3/16” for drywall, 7/32” for plaster)

• Hammer

• Pencil

• Electrical tape

• Level (optional)

Remove the wallplate from the ther-

mostat as shown at left, then follow

directions below for mounting.

1 Pull wires through wire hole.

2 Position wallplate on wall, level and

mark hole positions with pencil.

3 Drill holes at marked positions as

shown below, then tap in

supplied wall anchors.

4 Place wallplate over anchors, insert

and tighten mounting screws.

Grasp top and bottom of wallplate

and pull to remove from thermostat.

Drill 3/16” holes for drywall.

Drill 7/32” holes for plaster.

Wall anchors

Mounting screwsWire hole

Wallplate installation

PRO TH3110B Non-programmable Digital Thermostat

Installation Guide

Wiring

1 Loosen screw terminals, insert

wires into terminal block, then re-

tighten screws.

2 Push excess wire back into the

wall opening. Keep wires in shaded

area as shown at left.

3 Plug the wall opening with non-

flammable insulation to prevent

drafts from affecting thermostat

operation.

Terminal Designations

WWHeat relay.

YYCompressor contactor.

GGFan relay.

OOHeat pump changeover valve ener-

gized in cooling.

RRccCooling power. Connect to

secondary side of cooling

system transformer.

RRHeating power. Connect to

secondary side of heating

system transformer.

BBHeat pump changeover valve ener-

gized in heating.

Terminal

block

NOTES

R & Rc terminals

In single-transformer system, leave metal

jumper in place between R & Rc. Remove

metal jumper if two-transformer system.

Heat pump systems

If wiring to a heat pump, use a small piece of

wire (not supplied) to connect terminals W

and Y.

Wire specifications

Use 18- to 22-gauge thermostat wire.

Shielded cable is not required.

Keep wires in this

shaded area

CAUTION: ELECTRICAL HAZARD. Can cause electrical shock or equipment damage.

Disconnect power before wiring.

Wiring

Typical 1H/1C system: 1 transformer Typical 1H/1C system: 2 transformers

Power supply. Provide disconnect means and overload protection as required.

Factory-installed jumper. Remove for 2-transformer systems only.

Use either Oor Bterminals for changeover valve.

Use a small piece of wire (not supplied) to connect Wand Yterminals.

Set fan operation switch to Heat Pump (see page 6) and configure for heat pump (see pg. 8).

Remove jumper

Wiring diagrams

Typical 1H/1C heat pump system Typical heat-only system

Typical heat-only system with fan Typical cool-only system

PRO TH3110B Non-programmable Digital Thermostat

Installation Guide

Wiring

1 Loosen screw terminals, insert

wires into terminal block, then re-

tighten screws.

2 Push excess wire back into the

wall opening. Keep wires in shaded

area as shown at left.

3 Plug the wall opening with non-

flammable insulation to prevent

drafts from affecting thermostat

operation.

Terminal Designations

WWHeat relay.

YYCompressor contactor.

GGFan relay.

OOHeat pump changeover valve ener-

gized in cooling.

RRccCooling power. Connect to

secondary side of cooling

system transformer.

RRHeating power. Connect to

secondary side of heating

system transformer.

BBHeat pump changeover valve ener-

gized in heating.

Terminal

block

NOTES

R & Rc terminals

In single-transformer system, leave metal

jumper in place between R & Rc. Remove

metal jumper if two-transformer system.

Heat pump systems

If wiring to a heat pump, use a small piece of

wire (not supplied) to connect terminals W

and Y.

Wire specifications

Use 18- to 22-gauge thermostat wire.

Shielded cable is not required.

Keep wires in this

shaded area

CAUTION: ELECTRICAL HAZARD. Can cause electrical shock or equipment damage.

Disconnect power before wiring.

Wiring

Typical 1H/1C system: 1 transformer Typical 1H/1C system: 2 transformers

Power supply. Provide disconnect means and overload protection as required.

Factory-installed jumper. Remove for 2-transformer systems only.

Use either Oor Bterminals for changeover valve.

Use a small piece of wire (not supplied) to connect Wand Yterminals.

Set fan operation switch to Heat Pump (see page 6) and configure for heat pump (see pg. 8).

Remove jumper

Wiring diagrams

Typical 1H/1C heat pump system Typical heat-only system

Typical heat-only system with fan Typical cool-only system

PRO TH3110B Non-programmable Digital Thermostat

Installation Guide

•GGaassoorrOOiill::For gas or oil heating

systems, leave the fan operation

switch in this factory-set position

(This setting is for systems that

control the fan in a call for heat.)

•EElleeccttrriiccoorrHHeeaattPPuummpp::Change the

switch to this setting for heat

pump or electric heat systems.

(This setting is for systems that

allow the thermostat to control the

fan in a call for heat, if a fan wire is

connected to the GG

terminal.)

Set fan operation switch

Fan operation settings

Install batteries in back of thermostat

Install two AA alkaline batteries in the

back of the thermostat, as shown at

left.

Fresh batteries should be installed

immediately when the RREEPPLLAACCEEBBAATTTTwarn-

ing begins flashing (see page 10.) The

warning flashes about two months

before batteries are depleted.

Even if the warning does not appear,

Batteries should be replaced once a year,

or before the home is left vacant for

more than a month.

Battery installation

Align the 4 tabs on the wallplate with

corresponding slots on the back of the

thermostat, then push gently until the

thermostat snaps

in place.

Thermostat mounting

PRO TH3110B Non-programmable Digital Thermostat

Installation Guide

•GGaassoorrOOiill::For gas or oil heating

systems, leave the fan operation

switch in this factory-set position

(This setting is for systems that

control the fan in a call for heat.)

•EElleeccttrriiccoorrHHeeaattPPuummpp::Change the

switch to this setting for heat

pump or electric heat systems.

(This setting is for systems that

allow the thermostat to control the

fan in a call for heat, if a fan wire is

connected to the GG

terminal.)

Set fan operation switch

Fan operation settings

Install batteries in back of thermostat

Install two AA alkaline batteries in the

back of the thermostat, as shown at

left.

Fresh batteries should be installed

immediately when the RREEPPLLAACCEEBBAATTTTwarn-

ing begins flashing (see page 10.) The

warning flashes about two months

before batteries are depleted.

Even if the warning does not appear,

Batteries should be replaced once a year,

or before the home is left vacant for

more than a month.

Battery installation

Align the 4 tabs on the wallplate with

corresponding slots on the back of the

thermostat, then push gently until the

thermostat snaps

in place.

Thermostat mounting

PRO TH3110B Non-programmable Digital Thermostat

Installation Guide

System type

Heating cycle rate

(CPH: cycles/hour)

Compressor

cycle rate (CPH)

Temperature

display

Compressor

protection

0 Gas, oil or electric heat with air conditioning

1 Heat pump (5 minute compressor off time in heating and cooling)

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

9 For electric furnaces

[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]

3 Recommended for most compressors

[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]

0 Fahrenheit

1 Celsius

5 Five-minute compressor off time **See page 10

[Other options: 0, 1, 2, 3 or 4-minute off time]

Setup Function Settings & Options

To begin, press and hold the and

buttons until the display changes

Function

number

Press to change settings

Press to advance to next function

Press and hold to exit and save settings

Setting

Installer setup

Follow the procedure below to configure the thermostat to match the installed

heating/cooling system, and customize feature operation as desired.

Setup 10 0

Test

Heating system

Cooling system

Thermostat

information

(for reference only)

0 Heat and fan turn off.

1 Heat turns on. Fan also turns on immediately if Fan Operation

Switch is set to Electric Heat/Heat Pump (see page 6).

0 Compressor and fan turn off.

1 Compressor and fan turn on.

71 Software revision number (major revisions)

72 Software revision number (minor revisions)

73 Configuration identification code (major)

74 Configuration identification code (minor)

75 Production configuration date code (week)

76 Production configuration date code (year)

System Test System Status

Installer system test

CAUTION: EQUIPMENT DAMAGE HAZARD

Compressor protection (minimum off time) is bypassed during testing. To prevent

equipment damage, avoid cycling the compressor quickly.

System switch

System test

number

System status

Installer system test

After completing the installer setup above, press the button again to begin a

system test (see next page).

Press and hold both buttons

1 Set SSYYSSTTEEMMswitch to Cool.

2 Press to turn on cooling system, then check system status (see table, below).

3 Press to turn off cooling system.

4 Set SSYYSSTTEEMMswitch to Heat.

5 Press to turn on heating system, then check system status (see table, below).

6 Press to turn off heating system.

7 [Optional] Set SSYYSSTTEEMMswitch to Offto display thermostat information (see table, below).

Press to display 71-76.

8Press and hold to terminate system test at any time.

Follow the procedure below to test the heating and cooling system.

Otros manuales para PRO TH3110B

Tabla de contenidos

Otros manuales de Termostato de Honeywell

Honeywell

Honeywell Chronotherm IV Manual de usuario

Honeywell

Honeywell T810A Manual de usuario

Honeywell

Honeywell T10 Pro Smart Manual de usuario

Honeywell

Honeywell RTHL2510 series Manual de usuario

Honeywell

Honeywell MagicStat CT3300 Especificaciones técnicas

Honeywell

Honeywell DTC 100/2 Manual de operación y mantenimiento

Honeywell

Honeywell AQ1000TN2 - Low Voltage T-Stat Manual de usuario

Honeywell

Honeywell CM701 Instrucciones de instalación

Honeywell

Honeywell CM901 Instrucciones de instalación

Honeywell

Honeywell T8132A Manual de usuario

Honeywell

Honeywell Digital Round T8775A Manual de operación

Honeywell

Honeywell DT92A Guía de inicio rápido

Honeywell

Honeywell RTH9585WF1004 Manual de usuario

Honeywell

Honeywell TB6980 Manual de usuario

Honeywell

Honeywell RTH110B Manual de usuario

Honeywell

Honeywell lyric round Manual de usuario

Honeywell

Honeywell CT54 Manual de usuario

Honeywell

Honeywell t8034c Manual de usuario

Honeywell

Honeywell RLV430 Manual de usuario

Honeywell

Honeywell T87F Manual de usuario

Honeywell

Honeywell DT92E Manual de usuario

Honeywell

Honeywell Lyric T5 Wi-Fi Manual de usuario

Honeywell

Honeywell VisionPRO 8000 Manual de operación

Honeywell

Honeywell T7300F Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Aube Technologies

Aube Technologies TH305 Manual de usuario

Powtier Controls

Powtier Controls 505MST Manual de usuario

Kanmor

Kanmor Zone Control 369e Manual de usuario