Honeywell INNCOM e7w Manual de usuario

1 31-00308–01

e7w Wireless EMS Thermostat

INSTALLATION INSTRUCTIONS

FOR ALL UNITS IN CARTON. DO NOT THROW AWAY!

INSTALLATION REQUIREMENTS

Required Installation Hardware

•Four 6-32 × 1.5” Philips Pan head screws (provided with e7w) if attaching to a 4X4 electrical junction

box.

•Four AA alkaline batteries; provided with e7w.

•e7w Smart Wall Mounting Plate; provided with e7w.

•Three 4-24 1/2’’ Phillips screws Phillips captive screws; provided with e7w.

•Phillips Screwdriver.

•Wire cutters/strippers.

Required Commissioning Tools

DO NOT THROW THIS UNIT AWAY: One PC-503 USB Commissioning Tool and USB cable per property/project

is shipped to the site.

This tool is used in conjunction with Honeywell's engINN commissioning software when advanced commis-

sioning of the e7w is required by a trained and certified INNCOM technician. Contact Honeywell technical sup-

port for more information.

Figure 1: PC-503 USB commissioning tool and cable

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS

31-00308–01 2

CAUTION

•Read instructions carefully. Failure to follow

them could damage the product or create a

hazard.

•Check the ratings given in the instructions

and on the product to ensure that the prod-

uct is suitable for your application.

•Installer must be a trained, experienced ser-

vice technician.

•After installation is complete, check product

operation as indicated in instructions.

•For variations of these systems, refer to the

installation instructions of the controlled

equipment.

INSTALLATION

Location

Select a location about 1.5m (5ft.) above the floor

with good air circulation at average temperature.

Do not mount thermostat where it may be af-

fected by:

•Drafts or dead spots behind doors or in cor-

ners.

•Hot or cold air from ducts.

•Radiant heat from sun or appliances.

•Concealed pipes or chimneys.

•Unheated (un-cooled) areas behind the ther-

mostat.

•Near other RF sources/ transmitters to avoid

interference.

•When the thermostat is equipped with PIR,

consider view angle, range characteristics,

and mounting position for proper coverage.

Figure 2. Recommended mounting location

Mounting

The e7w Wireless EMS thermostat supports

mounting on the following standard mounting

junction boxes; US single-gang, US double-gang

and UK standard gang. The installation kit pro-

vides a Smart Wall Mounting Plate.

If mounted on a single-gang box, the right side

(keypad side) of the e7w overlaps the wall area to

the right.

To mount the e7w, follow the below steps:

1. Take the Smart Mounting Plate and orient it

with the raised arrow embossed on mounting

plate pointing UP.

2. Attach the plate to the junction box using the

supplied screws as shown in Figure 3.

3. Insert the 4 AA alkaline batteries.

Note:

•Use alkaline batteries only.

•Refer the “Battery details” sections for

more information.

4. After inserting AA batteries, all segments and

characters of the LCD are illuminated for

couple of seconds. Confirm all segments and

characters on the e7w LCD are displayed

correctly.

Refer LCD Display section for more details.

5. If the LCD displays blank information, run

the following checks:

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS

331-00308–01

a. Verify that the batteries installed in cor-

rect terminal.

b. Check the battery voltage.

6. Hook the tabs at the top rear of the e7w

housing into the matching depressions at

the top of the Smart Mounting Plate and ro-

tate the bottom of the housing toward the

wall until it snaps into place.

7. After startup, the e7w will cycle through RF

Channels 26, 25, 24… all the way to 11 and

send a 0x00061 Battery Powered thermostat

exchange message on each RF Channel

looking for a reply from an HVAC thermostat

partner with the same Room ID currently

stored in the e7w. Allow this process to con-

tinue until completion. Later you need to

configure the actual Room ID and other re-

quired parameters into the e7w.

8. Secure the housing to the Smart Mounting

Plate with the two small captive screws at the

bottom of the housing.

9. After you configured Room ID and other re-

quired parameters, restart the device and

wait for 5 seconds LCD will display all config-

ured values and various mods.

Figure 3. e7w exploded assembly reference

Battery Details

Figure 4. e7w Battery polarity reference

1. Battery Compartment: Holds 4 AA Alka-

line Batteries.

2. Insert the 4 AA alkaline batteries, match-

ing the “+” terminals on the batteries to

the “+” symbols in the battery compart-

ment, as shown in Fig. 4.

CAUTION

Risk of explosion if battery is replaced by an in-

correct type.

Dispose the used batteries as per instructions

under WEEE Directive 2012/19/EC.

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS

31-00308-01 4

Specifications

Mounting

Standard US Double Gang: w/o Spacer Ring

Standard US Single Gang: w/o Spacer Ring

Standard UK Single Gang: w/o Spacer Ring

Dimension

L 120mm x W 120mm x H (23) mm (w/o spacer)

Ambient Operating

41 to 149 °F (5 to 40 °C), 0-95% RH non-condensing

Ambient Storage

33 to 149 °F (1 to 65 °C)

C/F degrees display

Toggle Button located on front display.

In room Temperature

60°F to 85°F (± 1°F) [15°C to 30°C (± 0.5°C)]

Power

6VDC Alkaline Batteries.

Color Variants

Ice White & Black Onyx

Display resolution

HTN LCD, 0.5 °C (0.1 °F in test mode).

Standard dead band

2 °F (1 °C) between heating and cooling.

Thermostat Measurement range

33 to 99 °F (1 to 37 °C) +/- 1.8 °F.

Outdoor air temperature display

Temp 0 to 99 °F (-18 to 37 °C) as reported from web service

Motion sensor

120° View Angle, 10meter line of sight

Light Sensor

Gamma Value 0.7, Spectral response 550 –650nm.

Humidistat

3 % RH, in range from30-95 % RH +/- 5%.

Frequency range

2405MHz to 2480MHz

Maximum power

5dBm

Hardware version

Firmware version

1.1.0

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS

531-00308–01

Wireless Communications

Parameter

Description

RF Data Rate

250kbps

Antenna Type

SMT

Indoor range

70ft

Transmit Power

+5dBm

Receive Sensitivity

-95dBm

Frequency Band

2.4Ghz

Encryption

AES -128

Protocol

802.15.4

Frequency Channels

11-26

Note:

•Required Deep Mesh Network 2.4GHz.

LCD Display

Figure 5. e7w LCD display segments

Target (SET) temperature value

Temperature units

Door or Lanai

Measured temperature icon

Fan Speed (Low, Medium, High)

Auto Fan speed

Measured temperature value

Outside temperature icon

Heat only mode

Cool only mode

Eco mode

Equipment alarm

Low battery alarm

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS

31-00308-01 6

INITIAL SETUP

Before going through the initial setup se-

quences, ensure the thermostat is mounted and

connected to the Smart Wall.

Note:

−When properly connected, the thermo-

stat will proceed into INTIALIZATION

MODE and display rId.

−When not properly connected to the

Smart Wall Plate, the unit will display

the alert message SWp and the alert

icon will illuminate until the Smart Wall

Plate is connected.

If you see SWp on the display, most likely the

unit is not connected or properly seated on the

Smart Wall Plate. Unscrew the captive screws

and re-seat the thermostat. Once properly

connected, the display will start up as noted.

Take care not to over-tighten the screws and

note any irregularity on the wall surface that

may lead to an insecure connection between

the Smart Wall Plate and thermostat.

Setup Room ID

Figure 6. Setup Room ID

1. Once rld is displayed, press MODE. The de-

fault Room ID value (65535) is displayed and

will begin scrolling across the screen one nu-

merical setting at a time, from highest to low-

est (left most to right most value).

Note:

The five-digit number is comprised of three

fields: highest digit, middle two digits, low-

est two digits (HIMEDLO), default value

(65535). Three settings must be made.

2. In HI (high) value page, use the UP/DOWN

arrow buttons to change this value (range is

0-6). Press FAN to continue.

3. Set the MED (medium) values in the se-

quence using the UP/DOWN arrow buttons

(range is 0-99). Press FAN to continue.

4. Repeat the same step for the LO (low) two

values (range is 0-99) and press FAN to con-

tinue. Press MODE to accept the value.

5. The new ID number scrolls across the dis-

play. The unit beeps to confirm the value is

stored to memory. Once the scrolling is com-

pleted, screen will return to INTIALIZATION

MODE.

6. If you want to continue, press the DOWN ar-

row button to display rF mode (RF channel

for IRAS communication).

If you want to exit the INTIALIZATION MODE,

press the FCkey.

After you configured ROOM ID, you need to

configure RF channel for IRAS communica-

tion.

Figure 7. Configuring Room ID

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS

731-00308–01

Setup RF Channel

Figure 8. Setup RF Channel

1. After rF is displayed, press MODE.

2. Default rF value 26 displayed on the screen.

3. Use the UP/DOWN arrows to change value

range between 11 to 26.

4. Press FAN, the unit beeps to confirm the

value stored in the memory and display will

be back rF.

5. Press MODE to check the value.

6. Once the rF configured, Press FCto re-

turn INTIALIZATION MODE.

7. If you want to continue, press the DOWN ar-

row button to display PAn mode

If you want to exit the INTIALIZATION MODE,

press the FCkey.

After you configured RF channel, you need to

configure PAN channel for IRAS communica-

tion.

Figure 9. Configuring RF channel

Setup PAn ID

Figure 10. Setup PAn ID

After PAn is displayed, press MODE.

1. Default PAn value is 0 displayed on the

screen.

2. Use the UP/DOWN arrows to change value

range between 0 to 255.

3. Press FAN, the unit beeps to confirm the

value stored in the memory, the display will

be back to PAn.

4. Press MODE to check the value.

8. Once the PAn configured, Press FCto re-

turn INTIALIZATION MODE.

9. If you want to continue, press the DOWN ar-

row button to display rld mode

If you want to exit the INTIALIZATION MODE,

press the FCkey.

Service Mode

To configure the HVAC controller, wireless mo-

tion sensors, and doors/windows/balcony

switches with e7w, you need to set e7w into Ser-

vice Mode.

To enter Service, follow the below steps:

1. Press and hold FCkey.

2. Press and release MODE.

3. Press and release FAN.

4. Release FCkey.

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS

31-00308-01 8

BINDING AUXILIARY DEVICES

Note:

Before binding or verifying auxiliary devices.

•e7w must be configured with correct Room

ID, PAN ID, and RF Channel.

•For forward bind method, place the remote

device into a discovery mode that can re-

ceives the request sent from the thermo-

stat and reply to the request.

•For reverse bind method, mount the ther-

mostat in a such location, that can receive

request sent from the remote device and

reply to the request.

Binding PC502.4G

1. Enter SERVICE MODE. use the UP/DOWN

arrow buttons to select Io.

2. Press MODE. The information display

changes to show Io and a value.

3. Use the UP/DOWN arrow buttons to change

the displayed value range from 0 to 255. Set

the Io value to the desired I/O map number.

4. Press FAN to initiate a reverse bind.

5. Press Reset/Bind switch on the PC502.4g

(use a small point like the end of a straight-

ened paper clip).

If the PC502.4G binds successfully, it will

flash Led and send message to make the unit

beep, confirming that the bind was success-

ful.

6. Press FCto exit service mode.

Binding Door/Window/Balcony

Switch

1. Enter SERVICE MODE, use the UP/DOWN

arrow buttons to select Io.

2. Press MODE. The information display

changes to show Io and a value.

3. Use the UP/DOWN arrow buttons to change

the displayed value range from 0 to 255. Set

the Io value to the desired I/O map number.

4. Press FAN to initiate a reverse bind or press

MODE to initiate a forward bind.

5. Press the S1 switch on the device to initiate

binding process.

If the device binds successfully, it will flash

Led and send message to make the unit

beep, confirming that the bind was success-

ful.

6. Press FCto exit service mode.

Figure 11: Configuring IO mode

VERIFYING AUXILIARY DEVICES

1. Enter SERVICE MODE, use the UP/DOWN

arrow buttons to select PnG.

2. Press MODE. The information display

changes to show PNG and a value.

3. Use the UP/DOWN arrow buttons to the ad-

dress of the target device to be pinged.

4. Press FAN to initiate pinging the target de-

vice. After few seconds, it will start communi-

cating the reply and values will be displayed.

5. Press the FCbutton to stop pinging.

6. Press FCto exit service mode.

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS

931-00308–01

STANDARDS AND APPROVALS

•Product Standard −EN 60730-1:2011 and

EN 60730-2-9:2010 (covers EMC and LVD

Safety requirements).

•EMC Standard −ETSI 301489-1 V2.2.1, ETSI

301 489-17 V 3.2.0.

•EMC Standard EN 55032 −Radiated RF

Emissions.

UL (IEC)

•UL 60730-1, 5th edition and UL 60730-2-9,

4th edition.

•IEC and EN EMC standards:

oEU RoHs: EN 50581:2012 per EU RoHS

Directive 2011/65/EU,

oEN 50581:2012 per EU RoHS Directive

2011/65/EU.

oIEC60417, No.5957. For indoor use only.

oClass III equipment per IEC 61140.

•Radio –FCC Part 15 Subpart C (15.249), In-

dustry Canada RSS-210 Issue 9:2016 and

RSS-GEN Issue 4:2014.

•IPx1 protection.

•Pollution Degree 2.

•Type 1 action, operating control.

CSA

•CSA (IEC Based), Note 1 on standards,

Note 2 on aspects impacted by transition

•CAN/CSA E60730-1, 5th edition

•CAN/CSA E60730-2-9, 4th edition

Note 1

We have a choice of the IEC based path or

the updated version of Spec. 24. Considera-

tions:

•CSA C22.2 No. 24-93 has been in place

but will not be allowed from Jan. 1, 2017.

It is being replaced with CSA C22.2 No.

24-2015 as of that date (Environmental

Requirements).

•CSA C22.2 No. 24-2015 references CSA

C22.2 No. 0.8 for electronic controls with

safety functions, functional safety and

EMC instead of 60730-1 Annex H.

•According to CSA, the deviations for

Canada added to CAN/CSA 60730-1

and 60730-2-9 make this choice equiv-

alent to use of CSA C22.2 No. 24-2015.

Regulatory Compliance

UL Listing

This device meets UL 60730-2-9, CAN/CSA-

E60730-2-9 Standard for Automatic Electrical

Controls - Part 2-9: Requirements for Tempera-

ture Sensing Control

Federal Communications Commission

(FCC)

Changes or modifications not expressly ap-

proved by the party responsible for compliance

could void the user’s authority to operate the

equipment. This equipment has been tested and

found to comply with the limits for a Class B dig-

ital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a res-

idential installation. This equipment generates,

uses and can radiate radio frequency energy and,

if not installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

e7w WIRELESS EMS THERMOSTAT - INSTALLATION INSTRUCTIONS

31-00308-01 10

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one of the fol-

lowing measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equip-

ment and receiver.

•Connect the equipment into an outlet on a

circuit different from that to which the re-

ceiver is connected.

•Consult the dealer or an experienced ra-

dio/TV technician for help.

This device complies with FCC and IC radiation

exposure limits set forth for an uncontrolled en-

vironment. This device should be installed and

operated with minimum distance of 20cm be-

tween the radiator and your body. This device

must not be co-located or operating in conjunc-

tion with any other antenna or transmitter.

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause harm-

ful interference, and (2) this device must accept

any interference received, including interference

that may cause undesired operation.

Tout changement ou modification n’ayant pas

été expressément approuvé par la partie re-

sponsable de la conformité pourrait annuler

l’autorisation de l’utilisateur d’utiliser l’équipe-

ment. Cet équipement a subi des tests prouvant

sa conformité aux limites prescrites pour les ap-

pareils numériques de classe B, selon la partie

15 des règlements de la FCC. Ces limites ont été

conçues pour fournir une protection raison-

nable contre les interférences nuisibles lorsque

l’appareil est utilisé dans un environnement ré-

sidentiel. Cet équipement génère, utilise et peut

émettre de l’énergie radioélectrique et, s’il n’est

pas installé et utilisé conformément aux in-

structions, peut causer des interférences nuisi-

bles aux communications radio. Toutefois, il n’y

a aucune garantie que ces interférences ne

puissent survenir dans une installation par-

ticulier. Si cet équipement cause des interfé-

rences nuisibles à la réception de signaux de ra-

dio ou de télévision, ce qui peut être déterminé

en l’éteignant et en l’allumant, l’utilisateur peut

essayer de corriger ces interférences par les

mesures suivantes :

•Réorienter ou déplacer l’antenne récep-

trice.

•Augmenter la distance entre l’équipe-

ment et le récepteur.

•Brancher l’équipement sur un circuit dif-

férent de celui sur lequel le récepteur est

branché.

•Consulter le détaillant ou un technicien

expérimenté en radio/télévision pour de

l’aide.

Cet équipement est conforme aux limites d’ex-

position aux rayonnements FCC et IC établies

pour un environnement non contrôlé. Cet

équipement doit être installé et utilisé avec un

minimum de 20cm de distance entre la source

de rayonnement et votre corps. Cet appareil ne

doivent pas être placés à côté de ou fonctionner

en conjonction avec toute autre antenne ou

transmetteur.

Industry Canada (IC)

This device complies with Industry Canada li-

cense-exempt RSS standard(s). Operation is

subject to the following two conditions: (1) this

device may not cause interference, and (2) this

device must accept any interference, including

interference that may cause undesired operation

of the device.

Le présent appareil est conforme aux CNR d'In-

dustrie Canada applicables aux appareils radio

exempts de licence. L'exploitation est autorisée

aux deux conditions

suivantes: (1) l'appareil ne doit pas produire de

brouillage, et (2) l'appareil doit accepter tout

brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le

fonctionnement.

Otros manuales para INNCOM e7w

Tabla de contenidos

Otros manuales de Termostato de Honeywell

Honeywell

Honeywell TC300 Guía de configuración rápida

Honeywell

Honeywell Lyric Round TH8732WFH-5002/U Manual de usuario

Honeywell

Honeywell 191108AC Manual de usuario

Honeywell

Honeywell RTH7400 series Manual de usuario

Honeywell

Honeywell Q682B Manual de usuario

Honeywell

Honeywell T8141A Manual de usuario

Honeywell

Honeywell RTH8500 Series Manual de usuario

Honeywell

Honeywell T451A Manual de usuario

Honeywell

Honeywell Lyric T6 Pro Wi-Fi Manual de usuario

Honeywell

Honeywell Prestige IAQ YTHX9421 Manual de usuario

Honeywell

Honeywell TH8320R1003 Manual de operación

Honeywell

Honeywell Magic Stat MS3000 Manual de usuario

Honeywell

Honeywell FocusPRO 6000 Series Manual de usuario

Honeywell

Honeywell TROL-A-TEMP Q674B Manual de usuario

Honeywell

Honeywell 2450A Series Manual de usuario

Honeywell

Honeywell Tradeline T8511G Manual de usuario

Honeywell

Honeywell Honeywell Thermostat PRO TH3000 Series Manual de usuario

Honeywell

Honeywell RTH2300B Manual de usuario

Honeywell

Honeywell TL8230A Manual de usuario

Honeywell

Honeywell AQ1000TP2 - Programmable Hydronic Communicating... Manual de usuario

Honeywell

Honeywell HH07AT216 Manual de usuario

Honeywell

Honeywell T10 Pro Smart Manual de usuario

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Manual de usuario

Honeywell

Honeywell Q539A Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Aube Technologies

Aube Technologies TH305 Manual de usuario

Powtier Controls

Powtier Controls 505MST Manual de usuario

Kanmor

Kanmor Zone Control 369e Manual de usuario