Honeywell FocusPRO 6000 Series Manual de usuario

FocusPRO

6000Series

Installation

Instructions

Programmable

Digital

Thermostat

M29433

Wallplate installation

Remove the wallplate from the thermostat,

then follow directions below for mounting.

1. Remove battery holder.

2. Pull here to remove wallplate from new

thermostat.

3. Pull wires through wire hole.

4. Position wallplate on wall, level and mark

hole positions with pencil.

5. Drill holes at marked positions as shown

below, then tap in supplied wall anchors.

6. Place wallplate over anchors, insert and

tighten mounting screws.

7. Insert reference card.

M29369

Drill 7/32"

holes for

plaster.

Drill 3/16"

holes for

drywall.

Wire hole Mounting

screws

MCR29434

MCR29436

Power options

Wiring terminal designations

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

Keep wires in this

shaded

area

Connect Cfor primary AC power

(optional if batteries are installed).

Insert batteries for primary

or backup power.

Remove factory-

installed jumper

only for two-

transformer

systems.

Conventional Terminals:

Rc 24VAC power from cooling

transformer

R 24VAC power from heating

transformer

W Heat relay (stage 1)

W2 Heat relay (stage 2)

Y Compressor contactor (stage 1)

Y2 Compressor contactor (stage 2)

G Fan relay

C 24VAC common. For 2 transformer

systems, use common wire from

cooling transformer.

Heat Pump Terminals:

Rc 24VAC power from cooling

transformer

R 24VAC power from heating

transformer

O/B Changeover valve

Y Compressor contactor

Y2 Compressor contactor (stage 2)

-TH6320U only

G Fan relay

Aux/E Auxiliary/Emergency heat relay

L Sends output when set to Em. Heat

C 24VAC common

TH6110D

RcYWGRC

TH6220D

RcYWGW2Y2 RC

TH6320U

RcYWGW2Y2 RC

MCR29437A

TH6110D

RcYGRC

RcY

TH6220D

RcYGAux

TH6320U

MCR29438A

Aux

Wiring conventional systems

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

1H/1C System

(1 transformer)

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

W Heat relay

G Fan relay

Heat-only System

Rc Power [1]

R [R+Rc joined by jumper]

C 24VAC common [3]

W Heat relay

Heat-only System

(Series 20) [5]

Rc [R+Rc joined by jumper]

R Series 20 valve terminal “R” [1]

Y Series 20 valve terminal “W”

C 24VAC common [3]

W Series 20 valve terminal “B”

Heat-only System

(normally open zone

valve) [5]

Rc [R+Rc joined by jumper]

R Power [1]

Y Normally open zone valve

C 24VAC common [3]

1H/1C System

(2 transformers)

Rc Power (cooling transformer) [1, 2]

R Power (heating transformer) [1, 2]

Y Compressor contactor

C 24VAC common [3, 4]

W Heat relay

G Fan relay

Heat-only System

with Fan

Rc Power [1]

R [R+Rc joined by jumper]

C 24VAC common [3]

W Heat relay

G Fan relay

Cool-only System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

G Fan relay

2H/2C System

(1 transformer) [6]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor (stage 1)

C 24VAC common [3]

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

2H/2C System

(2 transformers) [6]

Rc Power (cooling transformer) [1, 2]

R Power (heating transformer) [1, 2]

Y Compressor contactor (stage 1)

C 24VAC common [3, 4]

W Heat relay (stage 1)

G Fan relay

W2 Heat relay (stage 2)

Y2 Compressor contactor (stage 2)

RcYWGRC

M29372

RcWRC

M29373

RcYWRC

M29374

RcYRC

M29375

RcYWG RC

M29376

RcWG RC

M29377

RcYG RC

M29378

RcYWGW2Y2 RC

M29379

RcYWGW2Y2 RC

M29380

NOTES

Wire specifications:

Use 18- to 22-gauge thermostat wire.

Shielded cable is not required.

[1] Power supply. Provide disconnect means

and overload protection as required.

[2] Remove jumper for 2-transformer systems.

[3] Optional 24VAC common connection.

[4] Common connection must come from cool-

ing transformer.

[5] In Installer Setup, set system type to

Heat Only.

[6] In Installer Setup, set system type to

2Heat/2Cool Conventional.

[7] In Installer Setup, set changeover valve to

O or B.

[8] In Installer Setup, set system type to

2Heat/1Cool Heat Pump.

[9] In Installer Setup, set system type to

2Heat/2Cool Heat Pump.

[10] In Installer Setup, set system type to

3Heat/2Cool Heat Pump.

[11] L terminal sends a continuous output when

thermostat is set to Em. Heat. Connect

to Honeywell zoning panels to switch the

panel to Emergency Heat.

MCR29453

Thermostat mounting

1. Push excess wire back into the

wall opening.

2. Plug wall opening with non-

flammable insulation.

3. Align the 4 tabs on the wallplate

with corresponding slots on the

back of the thermostat.

4. Push gently until the thermostat

snaps in place.

1H/1C Heat Pump

System

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

2H/1C Heat Pump

System (TH6220D

only) [8]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

Aux/E Auxiliary/Emergency heat relay

L Sends output when set to Em. Heat [11]

2H/1C Heat Pump

System (TH6320U

only) [8]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

Aux/E Auxiliary/Emergency heat relay

L Sends output when set to Em. Heat [11]

2H/2C Heat Pump

System (TH6320U

only) [9]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor (stage 1)

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

Y2 Compressor contactor (stage 2)

L Sends output when set to Em. Heat [11]

3H/2C Heat Pump

System (TH6320U

only) [10]

Rc Power [1]

R [R+Rc joined by jumper]

Y Compressor contactor (stage 1)

C 24VAC common [3]

O/B Changeover valve [7]

G Fan relay

Aux/E Auxiliary/Emergency heat relay

Y2 Compressor contactor (stage 2)

L Sends output when set to Em. Heat [11]

See Notes on page 3.

YGAux

YGY2

YGAux

Wiring heat pump systems

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

M29381

Done Next

MCR29454

Done Next

MCR29454

Follow the procedure below to configure

the thermostat to match the installed

heating/cooling system, and customize

feature operation as desired.

1. To begin, press and hold the s

and FAN buttons until the display

changes.

2. Press s or tto change settings.

3. Press NEXT to advance to next

function.

4. Press DONE to exit and save

settings.

Installer setup

Setup function Settings & options (factory default in bold)

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

1System type 0 1 heat/1 cool conventional

1 1 heat/1 cool heat pump (no aux. heat)

2 Heat only — 2-wire systems, 3-wire zone valves (Series 20),

and normally open zone valves

3 Heat only with fan

4 Cool only

5 2 heat/1 cool heat pump (with aux. heat)

6 2 heat/2 cool conventional

7 2 heat/1 cool conventional

8 1 heat/2 cool conventional

9 2 heat/2 cool heat pump (no aux. heat) - TH6320U only

10 3 heat/2 cool heat pump (with aux. heat) - TH6320U only

2Changeover valve

(O/B terminal)

0 Changeover valve (O/B terminal energized in cooling)

1 Changeover valve (O/B terminal energized in heating)

3Fan control

(heating)

0 Gas or oil furnace — equipment controls fan in heating

1 Electric furnace — thermostat controls fan in heating

5Stage 1 heat cycle

rate

(CPH: cycles/hour)*

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

9 For electric furnaces

6Stage 2 heat cycle

rate/Auxiliary heat

cycle rate (CPH)*

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

9 For electric furnaces

7Auxiliary heat

cycle rate (CPH)*

Only TH6320U

for 3H/2C Heat

Pumps

5 For gas or oil furnaces of less than 90% efficiency

1 For steam or gravity systems

3 For hot water systems & furnaces of over 90% efficiency

9 For electric furnaces

Function

number Setting

*[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]

9 Stage 1 compressor

cycle rate (CPH) 3 Recommended for most compressors

[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]

10 Stage 2 compressor

cycle rate (CPH) 3 Recommended for most compressors

[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]

12 Manual/Auto

changeover 0 Manual changeover (Heat/Cool/Off)

1 Auto changeover (Heat/Cool/Auto/Off)

2 Auto changeover only (Auto)

13 Adaptive Intelligent

Recovery™ 1 On**See page 8

0 Off

14 Temperature

display 0 Fahrenheit

1 Celsius

15 Compressor

protection 5 Five-minute compressor off time

[Other options: 0, 1, 2, 3 or 4-minute off time]

16 Schedule format 0 5/2 (programmable weekdays and weekends)

1 5/1/1 (weekdays, Saturday & Sunday programmable)

26 Auxiliary heat

control 0 Comfort

1 Economy

27 Heat temperature

range stops 90 Max. heat temperature setting is 90 °F (32 °C)

[Other options: 40 °F to 89 °F (4.5 °C to 31.5 °C)]

28 Cool temperature

range stops 50 Min. cool temperature setting is 50 °F (10 °C)

[Other options: 51 °F to 99 °F (10.5 °C to 37 °C)]

Setup function Settings & options (factory default in bold)

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

Special function

Auto Changeover (Setup Function 12): When set to Auto, the thermostat

automatically selects heating or cooling depending on the indoor temperature.

The thermostat will automatically adjust heat and cool settings to maintain

a 3-degree separation (fixed). Note: If you select Auto Changeover Only,

the System Setting on the thermostat will stay locked in the Auto position,

preventing the user from changing it to Em Heat, Heat, Cool or Off.

Adaptive Intelligent Recovery™ (Setup Function 13): Allows the thermostat

to “learn” how long the furnace and air conditioner take to reach programmed

temperature settings, so the temperature is reached at the scheduled time.

Compressor Protection (Setup Function 15): Forces the compressor to wait

a few minutes before restarting, to prevent damage. During the wait time, the

message Cool On or Heat On (heat pumps only) will flash on the display.

10 0

MCR2945

10 0

MCR29455

Installer system test

1. To begin, press and hold the

sand tbuttons until the

display changes.

2. Press s/ tto turn system

on/off.

3. Press NEXT to advance to next

test

4. Press DONE to terminate

system test.

Temperature Ranges

Heat: 40° to 90°F (4.5° to 32°C)

Cool: 50° to 99°F (10° to 37°C)

Operating Ambient Temperature

32° to 120°F (0° to 48.9°C)

Shipping Temperature

-20° to 120°F (-28.9° to 48.9°C)

Operating Relative Humidity

5% to 90% (non-condensing)

Physical Dimensions

3-9/16” H x 5-13/16” W x 1-1/2” D

91 mm H x 147 mm W x 38 mm D

Electrical Ratings

Terminal Voltage (50/60Hz) Running Current

WHeating 20-30 Vac 0.02-1.0 A

(Powerpile) 750 mV DC 100 mA DC

W2 (Aux/E) Heating 20-30 Vac 0.02-1.0 A

YCooling 20-30 Vac 0.02-1.0 A

Y2 Cooling 20-30 Vac 0.02-1.0 A

GFan 20-30 Vac 0.02-0.5 A

O/B Changeover 20-30 Vac 0.02-0.5 A

LOutput 20-30 Vac 0.02-0.5 A

Specifications

System test System status

Shaded areas below apply only to TH6320U/TH6220D or as otherwise noted.

10 Heating system 0 Heat and fan turn off.

1 Stage 1 heat turns on. Fan turns on if Setup Function 1 is

set to 1, 5, 9 or 10 OR Setup Function 3 is set to 1

2 Stage 2 heat turns on

3 Stage 3 heat turns on - TH6320U only

20 Emergency heating

system 0 Heat and fan turn off

1 Heat and fan turn on

30 Cooling system 0 Compressor and fan turn off

1 Compressor and fan turn on

2 Stage 2 compressor turns on

40 Fan system 0 Fan turns off

1 Fan turns on

System test

number System

status

Automation and Control Solutions

Honeywell International Inc.

1985 Douglas Drive North

Golden Valley, MN 55422

Honeywell Ltd

705 Montrichard Avenue

Saint-Jean-sur-Richelieu, Québec

J2X 5K8

customer.honeywell.com

® U.S. Registered Trademark.

69-2695EFS—05 M.S. Rev. 03-14

Printed in U.S.A.

69-2695EFS-05

For assistance with this product, please

visit customer.honeywell.com.

Or call Honeywell Customer Care toll-

free at 1-800-468-1502.

Customer assistance

Turn thermostat

over to find model

number and date

code.

Pull at bottom

to remove

thermostat

from

wallplate.

CAUTION:

EQUIPMENT DAMAGE HAZARD

Compressor protection is bypassed during testing. To prevent equipment damage, avoid

cycling the compressor quickly.

CAUTION:

ELECTRICAL HAZARD

Can cause electrical shock or equipment damage. Disconnect power before beginning

installation.

CAUTION:

MERCURY NOTICE

If this product is replacing a control that contains mercury in a sealed tube, do not

place the old control in the trash. Contact your local waste management authority for

instructions regarding recycling and proper disposal.

FocusPRO

6000Série

Thermostat

numérique

programmable

Notice

D’installation

M29433

M29369

Installation de la plaque murale

Séparer la plaque murale du thermostat

comme, puis suivre les directives

d’installation.

1. Retirer le porte-pile.

2. Tirer ici pour enlever la plaque murale du

thermostat neuf.

3. Faire passer les fils par l’ouverture

réservée aux fils.

4. Placer la plaque murale sur le mur,

mettre de niveau et marquer au crayon

l’emplacement des trous.

5. Percer les trous aux endroits marqués à

l’aide d’une perceuse, puis insérer les

chevilles d’ancrage fournies.

6. Apposer la plaque murale sur les

chevilles, insérer puis resserrer les vis de

fixation.

7. Insérer la carte de référence.

Trou du fil Vis de montage

Utiliser une

mèche de

3/16 po si le

mur est en

placoplâtre

Utiliser une mèche

de 7/32 po si le

mur est en plâtre.

MCR29434

MCR29436

Options d’alimentation

Désignation des bornes

Les zones ombragées ci-dessous s’appliquent seulement au TH6320U/

TH6220D ou selon les indications.

Garder les fils dans

cettezone

ombragée

Brancher Cpour l’alimentation

CA primaire (facultatif si des piles

sont installées).

Insérer les piles pour l’alimentation

primaire ou de secours.

Enlever le cavalier

installé en usine

uniquement pour

les systèmes

à deux

transformateurs.

Bornes traditionnelles :

Rc Alimentation de 24 V CA pour

le transformateur de climatisation

R Alimentation de 24 V CA pour

le transformateur de chauffage

W Relais de chauffage (stade 1)

W2 Relais de chauffage (stade 2)

Y Contacteur du compresseur (stade 1)

Y2 Contacteur du compresseur (stade 2)

G Relais de la soufflante

C Neutre 24 V CA Pour les systèmes

à 2 transformateurs, utiliser le neutre

pour le transformateur de climatisation

Bornes de thermopompe :

Rc Alimentation de 24 V CA pour

le transformateur de climatisation

R Alimentation de 24 V CA pour

le transformateur de chauffage

O/B Robinet de substitution

Y Contacteur de compresseur

Y2 Contacteur du compresseur (stade 2)

-TH6320U seulement

G Relais de la soufflante

Aux/E Relais auxiliaire de chauffage/

de chauffage d’urgence

L Envoie le signal de sortie lorsque réglé

à Em. Chauffage

C Neutre 24 V CA

TH6110D

RcYWGRC

TH6220

RcYWGW2Y2 RC

TH6320

RcYWGW2Y2 RC

MCR29437A

TH6110D

RcYGRC

RcY

TH6220D

RcYGAux

TH6320U

MCR29438A

Aux

Otros manuales para FocusPRO 6000 Series

Tabla de contenidos

Idiomas:

Otros manuales de Termostato de Honeywell

Honeywell

Honeywell T9 Manual de usuario

Honeywell

Honeywell FocusPRO 6000 Series Manual de usuario

Honeywell

Honeywell RET97A5 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

Honeywell

Honeywell TRADELINE T874 Manual de operación

Honeywell

Honeywell T7351 Manual de usuario

Honeywell

Honeywell C7189R2002-2 Manual de usuario

Honeywell

Honeywell T8611 Manual de usuario

Honeywell

Honeywell RTH7000 Manual de usuario

Honeywell

Honeywell Q539A Manual de usuario

Honeywell

Honeywell RTH221 Series Manual de usuario

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Manual de usuario

Honeywell

Honeywell CT62A Manual de usuario

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Manual de usuario

Honeywell

Honeywell T8601D Manual de usuario

Honeywell

Honeywell FocusPRO 5000 Series Manual de usuario

Honeywell

Honeywell CT1800 Manual de usuario

Honeywell

Honeywell VisionPRO TH8000 Series Manual de usuario

Honeywell

Honeywell TL5110 Manual de usuario

Honeywell

Honeywell Lyric T6 Pro Wi-Fi Manual de usuario

Honeywell

Honeywell MagicStat T8132 Manual de usuario

Honeywell

Honeywell PRO TH2000DV Series Manual de usuario

Honeywell

Honeywell TP970 Series Manual de uso y cuidado

Honeywell

Honeywell INNCOM e7w Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Aube Technologies

Aube Technologies TH305 Manual de usuario

Powtier Controls

Powtier Controls 505MST Manual de usuario

Kanmor

Kanmor Zone Control 369e Manual de usuario