Honeywell 10260 Series Manual de usuario

Tabla de contenidos

Otros manuales de Cambiar de Honeywell

Honeywell

Honeywell Q682B Guía del usuario

Honeywell

Honeywell DPSL200 Manual de usuario

Honeywell

Honeywell 968XTP Manual de usuario

Honeywell

Honeywell nfs2-3030 Manual de usuario

Honeywell

Honeywell 50054911 Manual de usuario

Honeywell

Honeywell krom schroder 03250831 Manual de usuario

Honeywell

Honeywell CX Series Guía rápida

Honeywell

Honeywell 39351 Manual de usuario

Honeywell

Honeywell BX Series Manual de usuario

Honeywell

Honeywell Galaxy 2 Series Manual de usuario

Honeywell

Honeywell ZW4003 Manual de usuario

Honeywell

Honeywell 43191680-105 Manual de usuario

Honeywell

Honeywell ZW4008 Manual de usuario

Honeywell

Honeywell DCM/SN DIFF Manual de usuario

Honeywell

Honeywell MICRO SWITCH GSX Manual de usuario

Honeywell

Honeywell RPLS540A Manual de usuario

Honeywell

Honeywell Switches Manual de usuario

Honeywell

Honeywell C6097 Manual de usuario

Honeywell

Honeywell C645A-E Manual de operación

Honeywell

Honeywell 39342 Manual de usuario

Honeywell

Honeywell HBADZ600 Manual de usuario

Honeywell

Honeywell PLS731B Manual de usuario

Honeywell

Honeywell RXSW100A3CULH Manual de usuario

Honeywell

Honeywell CLMSOPS5M Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario

62-86-33-34 Page 1 of 2

10260 Series Auto/Manual Switch kit

Replacement/Upgrade Instructions

51309623-501

Document Information

Number: 62-86-33-34

Effective: 5/04

Supersedes: None

Summary

This kit contains a new auto/manual switch assembly for your 10260 actuator.

Procedure

See Table 1 for procedure.

WARNING

WARNING

Disconnect power before accessing components inside the instrument.

ATTENTION

When working with circuit cards always protect against electrostatic discharge by wearing a grounded wrist

strap.

Table 1 10260A Auto/Manual Switch Installation Procedure

Step Action

1 Remove lower rear cover.

2 Remove terminal board plate.

3 If replacing the switch, disconnect switch wires and remove switch:

• Disconnect the auto/manual switch wires from terminals 9, 10, 11, and 12 (upper terminal board).

Disconnect the three auto/manual switch wires connected to the bottom terminal board, record the colors of

the wires removed and their associated terminal numbers.

• Remove switch knob by pulling it off the shaft.

• Remove nut securing switch to side of unit.

• Pull switch out of unit side wall.

Page 2 of 2 62-86-33-34

Step Action

4 Install new switch:

• See Figure 1. Attach switch label to side wall.

• Remove nut from threads on switch. Insert switch through side wall. Make sure the stub

engages the small hole.

• Screw the nut onto the switch shaft and tighten it securely.

• Attach knob to shaft with set screw on flat side of shaft.

5 Connect switch wires:

• If adding (not replacing) the switch, add the second terminal board (terminals 13 thru 24) if needed.

• If adding (not replacing) the switch, remove the wires connected to terminals 11 and 12.

Connect the auto/manual switch red wire to terminal 11 and the red-black wire to terminal 12.

Select 3 adjacent terminals on the bottom terminal board, connect the auto/manual switch black wire

(120/240VAC), the violet wire (CW) and green-black wire (CCW).

• If adding or replacing the switch, connect the auto/manual switch violet-black wire to terminal 9 and brown-

black wire to terminal 10.

6 Reattach terminal board plate.

7 Install new gasket and reattach cover.

8 Check switch for proper operation:

• Reconnect power.

• Set switch to CW and check for clockwise motion.

• Set switch to CCW and check for counterclockwise motion.

• Set switch to A/M and check for motion per 4-20 mA.

• If motion is incorrect, disassemble and check wiring in step 5. Repeat steps 6-8.