Honeywell VISTA-128BPT Manual de usuario

VISTA-128BPT/

VISTA-250BPT/

VISTA-128BPTSIA

800-06905 6/10 Rev. E

IMPORTANT!

RECOMMENDATIONS FOR PROPER INTRUSION PROTECTION

For proper intrusion coverage, sensors should be located at every possible point of entry to a home or

commercial premises. This would include any skylights that may be present, and the upper windows in a

multi-level building.

In addition, we recommend that radio backup be used in a security system so that alarm signals can still

be sent to the alarm monitoring station in the event that the telephone lines are out of order (alarm

signals are normally sent over the phone lines, if connected to an alarm monitoring station).

EARLY WARNING FIRE DETECTION

Early warning fire detection is important in a home. Smoke and heat detectors have played a key role in

reducing fire deaths in the United States. With regard to the number and placement of smoke/heat

detectors, we subscribe to the recommendations contained in the National Fire Protection Association's

National Fire Alarm Code (NFPA 72).

SYSTEM COMPATIBILITY NOTICE

Your Honeywell security system is designed for use with devices manufactured or approved by Honeywell

for use with your security system. Your Honeywell security system is not designed for use with any device

that may be attached to your security system's keypad or other communicating bus if Honeywell has not

approved such device for use with your security system. Use of any such unauthorized device may cause

damage or compromise the performance of your security system and affect the validity of your Honeywell

limited warranty. When you purchase devices that have been manufactured or approved by Honeywell,

you acquire the assurance that these devices have been thoroughly tested to ensure optimum

performance when used with your Honeywell security system.

About This Manual

This manual is a step-by-step guide that will acquaint you with the system's features and benefits. It

defines the components and their functions, describes their operation, and provides clear step-by-step

instructions for normal and emergency procedures. Keep this manual in a convenient place so that you

can refer to it as necessary.

Table of Contents

••••••••••••••••••••••••••••••••••••••••••

1. SYSTEM OVERVIEW

General .............................................................................1

A Partitioned System .................................................2

Zones .................................................................................2

Fire Protection ..............................................................2

Carbon Monoxide Protection................................2

Alarms ...............................................................................2

False Alarm Prevention Features ........................3

Cross Zoning and Swinger Suppression..........3

Keypad Lockout ...........................................................3

Error Message Displayed ........................................3

Burglary Protection ....................................................4

Memory of Alarm .........................................................4

Speed Key (Macros) ...................................................4

Using Schedules..........................................................4

Device Timers ................................................................5

Accessing another Partition (GOTO

Command)......................................................................5

Master Keypad Operation .......................................5

Self-Help Feature ........................................................5

Viewing Abbreviated Messages ...........................5

2. ABOUT THE KEYPADS

General .............................................................................6

The Alpha Keypad........................................................6

3. FUNCTIONS OF THE KEYPADS

4. ENTRY/EXIT DELAYS

General Information................................................10

Exit Delay......................................................................10

Entry Delay...................................................................10

Defaults and Requirements................................10

Exit Delay Reset.........................................................10

Burglar Alarm Communication Delay ............10

5. SECURITY CODES AND AUTHORITY

LEVELS

General Information ............................................... 11

Duress Code............................................................... 11

Quick Arming ............................................................. 11

Installer Code Lockout.......................................... 11

Authority Levels........................................................ 12

Authority Levels and Changes .......................... 13

To Exit User Edit Mode ......................................... 13

To Add a User............................................................. 14

To Change a User's Code..................................... 16

To Delete a User ....................................................... 17

6. ACCESSING OTHER PARTITIONS

To Access another Partition (GOTO).............. 18

7. GLOBAL ARMING

Global Arming Notes.............................................. 19

Global Arm................................................................... 19

Global Disarm............................................................ 19

8. MASTER KEYPAD

Operation..................................................................... 20

9. COMMON LOBBY

Operation..................................................................... 22

Affecting the Lobby (Disarming) ..................... 22

Arming the Lobby .................................................... 22

How User Codes Affect the Common

Lobby ............................................................................. 23

Codes with “Global” Arming................................ 23

Codes with “Non-Global” Arming..................... 23

Other Methods of Arming/Disarming........... 23

10. CHECKING FOR OPEN ZONES

Using the ∗READY Key ..............................24

Showing Faulted Zones.....................................24

11. DISPLAYING ALL ZONE DESCRIPTORS

Using the A∗AREADY Key............................25

Displaying Descriptors ......................................25

12. BYPASSING PROTECTION ZONES

Using the 6 BYPASS Key ............................26

To Bypass .................................................................26

Quick Bypass..........................................................27

Quick Bypassing ...................................................27

Viewing Bypassed Zones ..................................27

Group Bypass .........................................................28

Bypassing Groups................................................28

Zones Remaining Bypassed After

Disarming.................................................................29

13. ARMING STAY WITH ENTRY DELAY

Using the 3 STAY key ...................................30

Operation .................................................................30

Stay Modes..............................................................30

Arming STAY ...........................................................31

Auto-STAY Arming ...............................................31

14. ARMING STAY WITH NO ENTRY DELAY

Using the 7 INSTANT Key ..........................32

Operation .................................................................32

Instant Modes........................................................32

Arming INSTANT...................................................32

15. ARMING ALL PROTECTION (WITH ENTRY

DELAY)

Using the 2 AWAY Key .................................33

Operation .................................................................33

Arming Away ...........................................................33

16. ARMING ALL PROTECTION (NO ENTRY

DELAY)

Using the 4 MAXIMUM Key...................... 34

Operation................................................................. 34

Arming MAXIMUM.............................................. 34

17. QUICK EXIT

Using the # + 9 Keys.............................. 35

Arming with Quick Exit...................................... 35

18. DISARMING AND SILENCING ALARMS

Using the 1 OFF Key .................................... 36

Disarming the System....................................... 36

Memory of Alarm.................................................. 36

19. USING THE KEYSWITCH

General...................................................................... 37

Messages................................................................. 37

Arming....................................................................... 37

Disarming ................................................................ 37

20. CHIME MODE

Using the 9 Key .............................................. 38

Enabling the Chime............................................ 38

Disabling the Chime .......................................... 38

21. VIEWING ALARM COMPANY MESSAGES

General Information........................................... 39

22. PANIC KEYS

Using Panic Keys ................................................. 40

Activate Panic Functions................................. 40

Silent Emergency................................................. 40

Audible Emergency............................................. 40

Fire Alarm................................................................. 40

iii

23. SPEED KEY (MACROS)

General Information............................................41

Defining a Macro..................................................41

Executing .................................................................42

Automatic Macros................................................42

Manual Macros .....................................................42

24. ACCESS DOOR CONTROL

General Information............................................43

Executing .................................................................43

25. USING #70 RELAY MENU MODE

General Information............................................44

To activate relays from a keypad ..................44

26. USING SCHEDULES

Delaying the Closing Time...............................45

To delay the closing time..................................45

Temporary Open/Close Schedules.............46

27. PROGRAMMING DEVICE TIMERS

General Information............................................48

Randomize Output Device Times ................50

28. USING #77 INSTANT ACTIVATION MODE

Relay Commands .................................................51

Arm/Disarm Commands ..................................51

Bypass Commands .............................................52

Open/Close Windows ........................................52

Access Control Commands.............................52

Additional Commands.......................................53

To enter the Instant Activation Mode:........53

29. EVENT LOG PROCEDURES

General Information............................................54

To Display the Event Log..................................54

30. SETTING THE TIME AND DATE

31. TESTING THE SYSTEM

Using the 5 TEST Key .................................. 57

Testing Your System .......................................... 58

32. FIRE ALARM SYSTEM

General...................................................................... 59

In Case of Fire Alarm .......................................... 59

Silencing a Fire Alarm........................................ 59

33. TROUBLE CONDITIONS

Typical Trouble Displays .................................. 60

Power Failure ......................................................... 61

SERVICING INFORMATION............................ 61

34. RECOMMENDATIONS FOR PROPER

PROTECTION

Recommendations for Smoke and Heat

Detectors ................................................................. 62

Recommendations for Proper Intrusion

Protection...................................................................iii

35. EMERGENCY EVACUATION

36. MAINTAINING YOUR SYSTEM

Taking Care of Your System ........................... 65

Replacing Batteries in Wireless Sensors . 65

Silencing Low Battery Warning Tones at the

Keypad....................................................................... 66

Routine Care .......................................................... 66

37. QUICK GUIDE TO SYSTEM FUNCTIONS

38. SUMMARY OF AUDIBLE NOTIFICATION

39. INDEX

Section 1: System Overview

••••••••••••••••••••••••••••••••••••••••••

General

Your Honeywell security system consists of a main control, at least one keypad, and various sensors

strategically positioned throughout the premises. The system offers you three forms of protection:

burglary, fire and emergency. The keypad provides full control of system operation.

The system uses microcomputer technology to monitor all protection zones (doors, windows, smoke

alarms, etc.) and system status. It provides appropriate information for display on the keypad(s) used

with the system, and initiates appropriate alarms. Your system may also have been programmed to

automatically transmit alarm or status messages over the phone lines or cellular or IP communicator

to a central alarm monitoring station.

This manual is designed to help you become comfortable operating your system. Each function is

explained in step-by-step detail. We recommend you read the SYSTEM OVERVIEW section to become

familiar with the terminology and the basic features of the system.

NOTES:

•If you have a Graphic/Touch-Screen Keypad connected to your system, refer to the

Graphic/Touch-Screen Keypad User Guide for operating instructions.

•All references in this manual for number of zones, number of user codes, number of

access cards, and the event log capacity, use the VISTA-250BPT’s features.

•The following table lists the differences between the VISTA-128BPT/VISTA-128BPTSIA

and the VISTA-250BPT control panels. Additionally, only the VISTA-128BPT/VISTA-

128BPTSIA supports the capability to have a device duplicate keypad sounds at a

remote location. All other features are identical for both panels.

Feature

VISTA-128BPT/VISTA-128BPTSIA

VISTA-250BPT

Number of Zones

128

250

Number of User Codes

150

250

Number of Access Cards

250

500

Event Log Capacity

512

1000

VistaKey Modules

System Overview (cont’d)

A Partitioned System

Simply stated, a partitioned system shares one physical alarm system among different users, each

with their own requirements. For the most part, you as a user need not know about other users and

their structure in the system, but from time to time, you may see display messages that indicate the

system is in use by another user. Do not be concerned, this is normal. Refer to the ACCESSING OTHER

PARTITIONS section for additional information.

Zones

Your system's sensing devices have been assigned to various "zones." For example, the sensing device

on your Entry/Exit door may have been assigned to zone 001, sensing devices on windows in the

master bedroom to zone 002, and so on. These numbers will appear on the display, along with an

alpha descriptor for that zone (if programmed), when a fault, alarm or trouble condition occurs.

Fire Protection

The fire protection portion of your security system (if used) is always on and will sound an alarm if a

fire condition is detected. Refer to the FIRE ALARM SYSTEM section for important information

concerning fire protection, smoke detectors and planning emergency exit routes from your house.

Carbon Monoxide Protection

Carbon monoxide (CO) protection is available with your system using the 5800CO Carbon Monoxide

Detector. The 5800CO is a 3V battery powered wireless Carbon Monoxide Detector used with wireless

alarm systems that support 5800 series devices. Carbon monoxide gas is a highly poisonous gas

which is released when fuels are burned. It is invisible, has no smell and is therefore impossible to

detect with the human senses. We strongly suggest installing Carbon monoxide protection with your

system.

Alarms

When an alarm occurs, both the keypad and external sounders will sound, and the keypad will display

the zone(s) causing the alarm. If your system is connected to a central monitoring station, an alarm

message will also be sent. To stop the alarm sounding, simply disarm the system.

The Swinger Suppression feature of your system limits the number of times a non-fire zone locally

annunciates and transmits an alarm report to the central station. Ask your installer if this feature has

been programmed.

System Overview (cont’d)

False Alarm Prevention Features

Cross Zoning and Swinger Suppression

Cross Zoning and Swinger Suppression, options can help reduce false alarms.

•Cross Zoning: Requires activation of two zones within a specified time window

to activate an alarm.

•Swinger Suppression: Limits the number of messages sent for a specific zone in

an armed period. Swinger Suppression is by zone and is reset by

entering a valid User Code + Off.

Ask your installer if your system is programmed for either of these features.

Abort Window

An Abort Window feature exists for all non-fire zones. An Abort Window is a programmable time

window, which upon disarm (User Code + Off) after all non-fire alarm occurs, will be prevented from

reporting if disarmed within said window.

NOTE: Ask your installer if this feature has been programmed.

Keypad Lockout

•If a user presses 30 numeric keys (0-9) within a window of 15 minutes and no valid command is

executed, the system stops processing numeric key presses for a period of 15 minutes.

•During this lockout period, the control responds to any numerical key press with a long beep.

•In a partitioned system, a keypad that logs on to a locked out partition (using the GOTO

command) is locked out until the keypad is reconnected to its original partition, or until the

locked out partition’s lockout period expires, whichever occurs first. NOTE: No keypad activity for

two minutes will result in the keypad logging back into its home partition.

•When a 15-minute lockout occurs, a message is recorded in the Event Log (WNG CODE ENT).

When the 15-minute lockout window expires a WNG CODE RST message is recorded in the

Event Log.

Error Message Displayed

The displayed message on the keypad is as follows:

User Code Error

Key 0-9 Locked

The display is cleared when the lockout period expires, an

audible Alarm or the start of an Entry Time beginning.

System Overview (cont’d)

Burglary Protection

The burglary protection portion of your system must be turned on or "armed" before it will sense

burglary alarm conditions. Your system provides four modes of burglary protection: STAY, AWAY,

INSTANT and MAXIMUM, and even allows you to BYPASS selected zones of protection while leaving

the rest of the system armed. The system also provides a CHIME mode, for alerting users to the

opening and closing of doors and windows while the system is disarmed. Refer to the other sections of

this manual for procedures for using these features.

The following table lists the four different arming modes and the results of each.

Features For Each Arming Mode

Arming Mode

Exit

Delay

Entry

Delay

Perimeter

Armed

AWAY

Yes

STAY*

Yes

INSTANT*

Yes

MAXIMUM

Yes

∗The system provides three different STAY and INSTANT arming modes. See

ARMING IN THE STAY MODES and ARMING IN THE INSTANT MODES sections for

details on these modes.

Memory of Alarm

When an alarm condition occurs, the keypad displays the number(s) of the zone(s) that caused the

problem or alarm, and displays the type of alarm (ex. FIRE, ALARM). It remains displayed until it is

cleared by disarming the system (see DISARMING THE SYSTEM section).

Speed Key (Macros)

The system can store a string of up to 32 keystrokes, which can be activated anytime by simply

pressing the “A, B, C, or D” keys. This feature can be used to make it easy to perform multiple

functions at once (such as going to another partition to bypass a zone), or it can be used to simplify an

everyday, repeated procedure. Refer to the SPEED KEY section for procedures for using this feature.

Using Schedules

Your system may have been programmed with schedules for automatically arming, disarming and

activating various devices and/or performing other system functions at predetermined times. Users

can modify some of these schedules by manually delaying a closing time, using temporary schedules,

or by programming special user schedules. Refer to the USING SCHEDULES section at the end of this

manual for scheduling related procedures.

Otros manuales para VISTA-128BPT

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de seguridad de Honeywell

Honeywell

Honeywell DTPI8M Manual de usuario

Honeywell

Honeywell Tuxedo Touch Wi-Fi Manual de usuario

Honeywell

Honeywell Galaxy Dimension Manual de usuario

Honeywell

Honeywell ADEMCO Vista-12 Series Manual de usuario

Honeywell

Honeywell SILENT KNIGHT EVS Series Manual de usuario

Honeywell

Honeywell ADEMCO LYNXR-I Security System Manual de usuario

Honeywell

Honeywell SD500-PSDA Manual de usuario

Honeywell

Honeywell Galaxy 2-44 Manual de usuario

Honeywell

Honeywell ADEMCO VISTA-120 Manual de usuario

Honeywell

Honeywell VISTA-128BPT Guía de instalación

Honeywell

Honeywell LYNXR Manual de usuario

Honeywell

Honeywell LYNX Touch Security System Manual de usuario

Honeywell

Honeywell VISTA-21iP Manual de usuario

Honeywell

Honeywell Ademco VISTA-20P Manual de usuario

Honeywell

Honeywell Ademco VISTA-20P Instrucciones de funcionamiento

Honeywell

Honeywell LYNX Touch L7000 Series Manual de usuario

Honeywell

Honeywell Fire-Lite Alarms ES-50XC Manual de usuario

Honeywell

Honeywell ADEMCO 4110XM Manual de usuario

Honeywell

Honeywell NetAXS NX4S1 Manual de usuario

Honeywell

Honeywell Friedland FGGA07 Series Manual de usuario

Honeywell

Honeywell Fire-Lite Alarms MS-9200UDLSC Manual de usuario

Honeywell

Honeywell ADEMCO VISTA SERIES Manual de usuario

Honeywell

Honeywell ADEMCO LYNXR Series Manual de usuario

Honeywell

Honeywell LYNXRPK-2 - Wireless Self-Contained Security Syste - LYNXRPK-2 - Wireless Self-Contained Security... Instrucciones de montaje

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario