Honeywell Rae SensorRAE 4R+ Manual de usuario

The SensorRAE 4R+ is a storage case for non-EC (electrochemical) sensors and a warm-up station for EC sensors that

keeps them in a ready-for-use state. The water-resistant (IP-67) case accommodates six sensors and when used to warm

up sensors, its four AAA batteries typically last for six months.

Inserting/Replacing Batteries

CAUTION! Never change batteries or sensors in an area known to be hazardous.

The SensorRAE 4R+ uses fourAAAalkaline batteries (Duracell MN2400) to warm up sensors requiring it. If you are

using the SensorRAE 4R+ to carry sensors that do not require warming up, then there is no need for batteries.

The batteries are installed on the bottom of the interior unit. Grip the small tab at one end of the unit and then pull up to

lift the unit out of the SensorRAE 4R+’s compartment.

If batteries are already installed and require replacement, remove them. Then install new ones, being careful to match

the batteries’ direction to the polarities indicated by “+” in the battery holders.

Testing The Batteries

Press the button on the right side of the panel. The 5-segment LED ladder indicates the batteries’strength.

When the batteries are almost depleted, the bottom red LED flashes once per second. Any sensors undergoing

conditioning are still powered on. (Press the button to check the sensor state.)

When the batteries are completely depleted, all five red LEDs flash once per second, in sequence from top to bottom.

Any sensors undergoing warm-up are powered off. Therefore, those sensors will require warm-up time after the

batteries are changed.

Red LEDs on

Remaining capacity

80% to 100%

60% to 80%

40% to 60%

20% to 40%

0% to 20%

SensorRAE 4R+

User’s Guide

Press

Inserting Sensors

Important! Always make sure your hands are clean and dry before handling sensors.

Place a sensor into a socket, aligning it with the matching keyways and the multi-pin connector at the bottom. Once a

sensor is plugged in, its corresponding green LED flashes once and if it requires warm-up, then warm-up begins. Below

are approximate times for sensor warm-up.

Non-EC sensor: 0 hours (no warm-up required)

Non-biased EC sensor:6 hours

Biased EC sensor:24 hours

If the green LED does not blink, the sensor is not inserted properly.

Note: If the sensor is properly seated and you remove it at any time during its warm-up, it must be returned to its socket

within 20 seconds, or the SensorRAE 4R+ will restart the warm-up cycle from the beginning.

Removing Sensors

Always lift sensors out with your fingers, gripping around the sides.

Checking Sensor Status

You can check the status of a sensor being warmed up by pressing the power button. If the green LED next to the

sensor glows, it is fully conditioned and ready for use.

RAE Systems by Honeywell

World Headquarters

3775 N. First St.

San Jose, CA 95134-1708 USA

Phone: 408.952.8200

Fax: 408.952.8480

E-mail: customerserv@raesystems.com

Web Site: www.raesystems.com

Rev. A

February 2012

P/N T03-4001-000

Multi-pin Connector

Bottom

View

Top

View

Alignment keys

Sensor inserted

Alignment keyways (6x)

LED blinks once to

indicate

sensor has

been inserted correctly

Tabla de contenidos

Otros manuales de Hardware de red de Honeywell

Honeywell

Honeywell MAXPRO NVR SE Series Manual de usuario

Honeywell

Honeywell Internet Connection Module Manual de usuario

Honeywell

Honeywell Embedded NVR Manual de instrucciones

Honeywell

Honeywell HPM Instrucciones de montaje

Honeywell

Honeywell LonWorks protocol Manual de usuario

Honeywell

Honeywell HDCD8TP Manual de usuario

Honeywell

Honeywell MAXPRO PE Manual de usuario

Honeywell

Honeywell FUSION STREAMER Manual de usuario

Honeywell

Honeywell 2450Cm Series Manual de usuario

Honeywell

Honeywell Mesh Router Manual de usuario

Honeywell

Honeywell 057810 Manual de usuario

Honeywell

Honeywell VARIODYN D1 Manual de usuario

Honeywell

Honeywell Notifier NFN-GW-EM-3 Manual de usuario

Honeywell

Honeywell HN300401 Series Manual de usuario

Honeywell

Honeywell hus-nvr-1032-e Manual de usuario

Honeywell

Honeywell TotalPlant LCN Guía del usuario

Honeywell

Honeywell nfs2-3030 Manual técnico

Honeywell

Honeywell MIWI350 Manual de usuario

Honeywell

Honeywell 4909 CPVC Manual de usuario

Honeywell

Honeywell Q7055C1053 Manual de usuario

Honeywell

Honeywell 35 Series Manual de usuario

Honeywell

Honeywell HEN04111 Manual de usuario

Honeywell

Honeywell MAXPRO NVR Hybrid SE Manual de usuario

Honeywell

Honeywell MAXPRO NVR 3.1 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario