Honeywell FUSION STREAMER Manual de usuario

Document 900.0600 – 10/05 – Rev 1.00

Digital Video Transmission System

User Guide

FUSION STREAMER

Revisions

Issues Date Revisions

1.00 October 2005 Initial Release

FCC COMPLIANCE STATEMENT

INFORMATION TO THE USER: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO

COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF

THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION

AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A

COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE

RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH

THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO

COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY

TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO

CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.

CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY

RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE

EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME NMB-003

DU CANADA.

OPERATION OF THIS DEVICE IS SUBJECT TO THE FOLLOWING CONDITIONS:

THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE.

THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

THAT MAY CAUSE UNDESIRABLE OPERATION.

CABLES USED WITH THIS DEVICE MUST BE PROPERLY SHIELDED TO COMPLY WITH

THE REQUIREMENTS OF THE FCC.

YOU ARE CAUTIONED THAT ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY

APPROVED IN THIS MANUAL COULD VOID YOUR AUTHORITY TO OPERATE THIS

EQUIPMENT.

USERS OF THE PRODUCT ARE RESPONSIBLE FOR CHECKING AND COMPLYING WITH ALL

FEDERAL, STATE, AND LOCAL LAWS AND STATUTES CONCERNING THE MONITORING AND

RECORDING OF VIDEO AND AUDIO SIGNALS. HONEYWELL VIDEO SYSTEMS SHALL NOT BE

HELD RESPONSIBLE FOR THE USE OF THIS PRODUCT IN VIOLATION OF CURRENT LAWS

AND STATUTES.

NATIONAL POWER DEVIATION STANDARDS

AUSTRALIA / NEW ZEALAND

COMPONENTS COMPLY WITH THE RELEVANT PORTIONS OF IEC 60950 OR THE

APPLICABLE COMPONENT STANDARD OR THE RELEVANT AUSTRALIAN / NEW ZEALAND

STANDARD.

AC POWER DISTRIBUTION SYSTEMS CLASSIFIED AS TT OR IT ARE NOT ALLOWED

INTENDED FOR USE ON A TN SYSTEM.

--------------------------------------------------------------------

Rated Nominal

Current of cross-sectional

Equipment area

(A) (mm²)

--------------------------------------------------------------------

0.2 <= 3 0.5*

3 <= 7.5 0.75

7.5 <= 10 (0.75) 1.00

10 <= 16 (1,0) 1.5

16 <= 25 2.5

25 <= 32 4

32 <= 40 6

40 <= 63 10

63 <= 80 16

80 <= 100 25

100 <= 125 35

125 <= 160 50

160 <= 190 70

190 <= 230 95

DENMARK

CERTAIN TYPES OF CLASS I APPLIANCES MAY BE PROVIDED WITH PLUG NOT

ESTABLISHING EARTHING CONTINUITY WHEN INSERTED INTO DANISH SOCKET-OUTLETS.

"VIGTIGT !

LEDEREN MED GRØN/GUL ISOLATION MÅ KUN

TILSLUTTES EN KLEMME MÆRKET

(IEC 417, NO. 5019) ELLER (IEC 417, NO. 5017)

FOR TILSLUTNING AF DE ØVRIGE LEDERE, SE MEDFØLGENDE

INSTALLATIONSVEJLEDNING

SUPPLY CORD OF SINGLE-PHASE EQUIPMENT HAVING A RATED CURRENT NOT

EXCEEDING 13 A SHALL BE PROVIDED WITH A PLUG ACCORDING TO THE HEAVY

CURRENT REGULATIONS, SECTION 107-2-D1. CLASS I EQUIPMENT PROVIDED WITH

SOCKET-OUTLETS WITH EARTH CONTACT OR WHICH ARE INTENDED TO BE USED IN

LOCATIONS WHERE PROTECTION AGAINST INDIRECT CONTACT IS REQUIRED ACCORDING

TO THE WIRING RULES SHALL BE PROVIDED WITH A PLUG IN ACCORDANCE WITH

STANDARD SHEET DK 2-1A OR DK 2-5A. IF POLY-PHASE EQUIPMENT AND SINGLE-PHASE

EQUIPMENT HAVING A RATED CURRENT EXCEEDING 13 A IS PROVIDED WITH A SUPPLY

CORD WITH A PLUG, THIS PLUG SHALL BE IN ACCORDANCE WITH THE HEAVY CURRENT.

GERMANY

(GESETZ UBER TECHNISCHE ARBEITSMITTEL (GARATESICHERHEITSGESETZ) [LAW OF

TECHNICAL LABOUR EQUIPMENT {EQUIPMENT SAFETY LAW}], OF 23RD OCTOBER 1992,

ARTICLE 3, 3RD PARAGRAPH, 2ND SENTENCE, TOGETHER WITH THE "ALLGEMEINE

VERWALTUNGSVORSCHRIFT ZUR URCHFUHRUNG DES ZWEITEN ABSCHRITTS DES

GERATESICHERHEITSGESETZES" [GENERAL ADMINISTRATIVE REGULATION ON THE

EXECUTION OF THE SECOND SECTION OF THE EQUIPMENT SAFETY LAW], OF 10TH

JANUARY 1996, ARTICLE 2, THE PARAGRAPH, ITEM 2).

KOREA

PLUGS FOR THE CONNECTION OF THE APPARATUS TO THE SUPPLY MAINS COMPLY WITH

THE KOREAN REQUIREMENT (KSC 8305).

EMC - THE APPARATUS SHALL COMPLY WITH THE RELEVANT CISPR STANDARDS.

SWITZERLAND

SUPPLY CORDS OF EQUIPMENT HAVING A RATED CURRENT NOT EXCEEDING 10 A SHALL

BE PROVIDED WITH A PLUG

COMPLYING WITH SEV 1011 OR IEC 60884-1 AND ONE OF THE FOLLOWING DIMENSION

SHEETS:

SEV 6532-2.1991, PLUG TYPE 15, 3P+N+PE 250/400 V,10 A

SEV 6533-2.1991, PLUG TYPE 11, L+N 250 V,10 A

SEV 6534-2.1991, PLUG TYPE 12, L+N+PE 250 V,10 A

IN GENERAL, EN 60309 APPLIES FOR PLUGS FOR CURRENTS EXCEEDING 10 A. HOWEVER,

A 16 A PLUG AND SOCKETOUTLET SYSTEM IS BEING INTRODUCED IN SWITZERLAND, THE

PLUGS OF WHICH ARE ACCORDING TO THE FOLLOWING DIMENSION SHEETS, PUBLISHED

IN FEBRUARY 1998:

SEV 5932-2.1998, PLUG TYPE 25, 3P+N+PE 230/400 V,16 A

SEV 5933-2.1998, PLUG TYPE 21, L+N 250 V,16 A

SEV 5934-2.1998, PLUG TYPE 23, L+N+PE 250 V,16 A

UNITED KINGDOM

THE CURRENT RATING OF THE CIRCUIT SHALL BE TAKEN AS 13 A, NOT 16 A.

RATING OF CIRCUIT UNDER TEST WAS TAKEN TO BE 20 A.

APPARATUS WHICH IS FITTED WITH A FLEXIBLE CABLE OR CORD AND IS DESIGNED TO BE

CONNECTED TO A MAINS SOCKET CONFORMING TO BS 1363 BY MEANS OF THAT

FLEXIBLE CABLE OR CORD AND PLUG, SHALL BE FITTED WITH A "STANDARD PLUG" IN

ACCORDANCE WITH STATUTORY INSTRUMENT 1786: 1994 - THE PLUGS AND SOCKETS

ETC. (SAFETY) REGULATIONS 1994, UNLESS EXEMPTED BY THOSE REGULATIONS. NOTE:

"STANDARD PLUG" IS DEFINED IN SI 1786: 1994 AND ESSENTIALLY MEANS AN APPROVED

PLUG CONFORMING TO BS 1363 OR AN APPROVED CONVERSION PLUG.

RACK MOUNT INSTRUCTIONS

A) Elevated Operating Ambient – If installed in a closed or multi-unit rack assembly, the operating

ambient temperature of the rack environment may be greater than room ambient. Therefore,

consideration should be given to installing the equipment in an environment compatible with the

maximum ambient temperature (Tma) specified by the manufacturer.

B) Reduced Air Flow – Installation of the equipment in a rack should be such that the amount of air

flow required for safe operation of the equipment is not compromised.

C) Mechanical Loading – Mounting of the equipment in the rack should be such that a hazardous

condition is not achieved due to uneven mechanical loading.

D) Circuit Overloading – Consideration should be given to the connection of the equipment to the

supply circuit and the effect that overloading of the circuits might have on over current protection

and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when

addressing this concern.

E) Reliable Earthing – Reliable earthing of rack-mounted equipment should be maintained. Particular

attention should be given to supply connections other than direct connections to the branch circuit

(e.g. use of power strips).

UL NOTICE

Underwriters Laboratories Inc. has not tested the performance or reliability of the security or signaling

aspects of this product. UL has only tested for fire, shock and casualty hazards as outlined in UL’s

Standard for Safety UL 60950-1. UL Certification does not cover the performance or reliability of the

security or signaling aspects if this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR

CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY

SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.

CE NOTICE

This product is in conformity with the following European Directives:

ELECTROMAGNETIC COMPATIBILITY DIRECTIVE, 89/336/EEC

(as amended by 92/31/EECand by Article 5 of 93/68/EEC)

per the provisions of:

EN 55022:1994 EN 55024:1998 EN 61000-4-4:1995

EN 61000-3-2:1995 CISPR 24:1997 EN 61000-4-5:1995

EN 61000-3-3:1995 EN 61000-4-2:1995 EN 61000-4-6:1995

CISPR 22:1997 EN 61000-4-3:2002 EN 61000-4-11:1994

LOW VOLTAGE DIRECTIVE, 73/23/EEC

(as amended by Article 13 of 93/68/EEC)

per the provisions of:

EN 60950-1: 2001

EN 50130-4:1996 Notice

1. Uninterrupted Power supply (UPS)

2. Maximum lengths of wiring connected to the sensor inputs and control outputs are 30 meters.

EN 55022 CLASS A Notice

WARNING

This is a class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

IMPORTANT SAFEGUARDS

1. Read Owner’s Manual – After unpacking this product, read the owner’s manual carefully, and follow all the operating and other

instruction

2. Power Sources – This product should be operated only from the type of power source indicated on the label. If you are not sure of

the type of power supply to your home or business, consult your product dealer or local power company

3. Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to

protect it from overheating, and these openings must not be blocked or covered. The product should not be placed in a built-in

installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered

to.

4. Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products that

produce heat.

5. Water and Moisture – Do not use this product near water. Do not exceed the humidity specifications for the product as detailed in

the Appendix section in this manual

6. Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

7. Power Cord Protection – Power-supply cords should not be routed so that they are not likely to be walked on or pinched by items

placed against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the

product.

8. Overloading – Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a risk of fire

or electrical shock.

9. Lightning – For added protection for this product during storm, or when it is left unattended and unused for long periods of time,

unplug it from the wall outlet. This will prevent damage to the product due to lightning and power line surges.

10. Object and Liquid Entry Points – Never insert foreign objects into the Fusion Streamer unit, other than the media types approved

by Honeywell, as they may touch dangerous voltage points or short-out parts that could result in a fire or electrical shock. Never

spill liquid of any kind on the product.

11. Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious

personal injury and serious damage to the product.

12. Disc Tray – Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious personal injury.

13. Burden – Do not place a heavy object on or step on the product. The object may fall, causing serious personal injury and serious

damage to the product.

Tabla de contenidos

Otros manuales de Hardware de red de Honeywell

Honeywell

Honeywell HDCD8TP Manual de usuario

Honeywell

Honeywell MAXPRO NVR SE Manual de usuario

Honeywell

Honeywell hus-nvr-1032-e Manual de usuario

Honeywell

Honeywell Mesh Router Manual de usuario

Honeywell

Honeywell LonWorks protocol Manual de usuario

Honeywell

Honeywell Internet Connection Module Manual de usuario

Honeywell

Honeywell HN350401 Series Manual de usuario

Honeywell

Honeywell MAXPRO PE Manual de usuario

Honeywell

Honeywell Rae SensorRAE 4R+ Manual de usuario

Honeywell

Honeywell 2450Cm Series Manual de usuario

Honeywell

Honeywell Notifier NFN-GW-EM-3 Manual de usuario

Honeywell

Honeywell MAXPRO NVR Hybrid SE Manual de usuario

Honeywell

Honeywell MAXPRO 2.5 Manual de usuario

Honeywell

Honeywell 30 Series Manual de usuario

Honeywell

Honeywell VARIODYN D1 Manual de usuario

Honeywell

Honeywell 057810 Manual de usuario

Honeywell

Honeywell MAXPRO NVR PE Manual de usuario

Honeywell

Honeywell MAXPRO NVR SE Manual de usuario

Honeywell

Honeywell MAXPRO NVR SE Series Manual de usuario

Honeywell

Honeywell MAXPRO NVR XE Manual de usuario

Honeywell

Honeywell Q7055C1053 Manual de usuario

Honeywell

Honeywell HN300401 Series Manual de usuario

Honeywell

Honeywell Embedded NVR Manual de instrucciones

Honeywell

Honeywell HEN04111 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario