Honeywell NetAXS-123 Guía del usuario

NetAXS-123 Startup Guide, Document 800-05780V2

NetAXS-123

Startup Guide

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation.

DC OUT

COM

+24VDC IN

IN5

COM

IN6 (PWR FAIL)

HOLD B

HOLD A

BLUE

BRN / ORG

GREEN

WHITE

BLACK

RED

PURPLE

BLUE

YELLOW

IN4 (TAMPER B)

OUT4 (BZR)

IN3 (TAMPER A)

+12 V

GND

OUT2 (LED)

IN1 (REX)

COM

IN2 (STS)

NO/NC

DRY C

RETURN

NO/NC

DRY C

RETURN

110

RS485-2 used for

Downstream IO

SW2SW1

RS485_1 RS485_2

OUT 1 OUT 3

EXIT

Door Contact

(Optional)

+12V

EXT

Door Strike / Lock

Cat 5 Ethernet

Cable

(Optional)

Request to Exit (Optional)

Tamper Switch

12VDC Power Source (Optional)

Relay Jumpers for Output 1

(see Page 3)

Relay Jumpers for Output 3

(See Page 3)

Micro USB-B Cable (Optional)

Panel Power Options

Panel Communication Options

Reader A**

Reader B**

(Optional)

PoE

PWR

RUN

RDR

STS

Return

Dry C

NO/NC

Locking

Device

Return

Dry C

NO/NC

Locking

Device

External

Power

Supply

(+30VDC Max)

+ DC

+12VDC

Conguration

External

Power Supply

Conguration

** In order to connect an IN and OUT reader, BOTH readers must

have the HOLD line for proper operation.

“Hold A” and “Hold B” should be connected ONLY when

using BOTH an IN and an OUT reader.

NetAXS-123 Startup Guide, Document 800-05780V2

TABLE OF CONTENTS

1) Introduction ............................................................................................ 3

2) Before You Start ..................................................................................... 3

3) Device Connection Order ....................................................................... 4

4) Powering Up ........................................................................................... 4

5) Connecting to the Web Server ............................................................... 5

6) Logging In to the System ....................................................................... 7

7) System Configuration ............................................................................. 8

APPENDIX A) Adding a Panel ................................................................. 14

APPENDIX B) Adding a User ................................................................... 15

APPENDIX C) Changing the Ethernet Default IP Address ...................... 16

APPENDIX D) Enabling the In and Out Readers ..................................... 16

APPENDIX E) Additional Features ........................................................... 17

APPENDIX F) Monitoring Status............................................................... 20

APPENDIX G) Adding Additional Doors ................................................... 22

APPENDIX H) Resetting the Panel .......................................................... 22

1) Introduction

This document describes the basic setup, wiring and configuration steps

needed for the NetAXS-123 access control system.

NetAXS-123 can be configured in many different ways, depending on the

specific needs of the end-users. This document covers a single panel, 1 door

system. Additional doors are set up, wired and configured in a similar

manner to the first door. This document does not cover all of these

configurations.

For further configuration and setup information including installations related

to WIN-PAK and/or RS-485 communications please consult the NetAXS-123

User Guide and NetAXS-123 Installation Guide; both on NetAXS-123

Product CD.

2) Before You Start

1. Verify factory default DIP switch settings

(Address 1, Gateway Panel) as shown below:

NOTE: Actual DIP switch orientation may vary depending on the panel

mounting orientation. Please refer to Appendix G for more information on DIP

switch configuration. If using EVL, DIP switch addresses are not used as

addressing is configured in the web browser. Refer to Appendix A for

additional details.

2. Determine the power source: Power Over Ethernet (PoE) or 12VDC

power supply.

NOTE: If using PoE, a total maximum of 450ma @ 12VDC is available

for all external devices (locking device, reader(s), input and output devices).

3. Determine communications source: IP/Ethernet or USB.

4. Determine relay configuration (see the circuit diagram on Page 2).

12 34 56 7 8910

+12V NC

EXT NO

+12V NC

EXT NO

Whetted 12VDC

External (EXT) Power

• Power at relay terminals:

Whetted 12VDC (factory

default) or External (EXT)

power source:

• Relay Type: Normally Closed

(NC) or Normally Open

(NO, factory default):

+12V NC

EXT NO

+12V NC

EXT NO

Normally Open (NO )

Normally Closed (NC)

NetAXS-123 Startup Guide, Document 800-05780V2

3) Device Connection Order 4) Powering Up

1. Apply power (PoE or 12VDC power source) to panel.

2. Verify panel power up.

• The PoE or PWR LED will be illuminated and there

will be a slight delay as the operating system loads.

• RUN LED will initially be solid red then

steadily flash green, once per second.

3. Verify panel and wiring functionality.

• Trigger any input device. STS LED should flash

BLUE briefly.

• Swipe a card at any reader. RDR LED should flash

GREEN briefly.

Note: For dry-type configurations, the power supply must be voltage-

compatible, listed to UL 294 or UL 609 for UL installations and

CAN/ULC-S318 for ULC installations, and able to supply sufficient

backup power.

YOU HAVE SUCCESSFULLY POWERED UP

the NetAXS-123 Access Controller!

1. Reader(s) Connect readers to terminal block per

Connection Diagram.

2. Input Device(s) (if used) Connect Request to Exit Devices and/or

Door Status / Position Switch (if used) to

terminal block per Connection Diagram.

3. Output Device(s) Connect Locking Device(s) and/or

Auxiliary Devices (Intrusion, Sounder,

Strobe, etc.) (if used) to terminal block

per Connection Diagram.

Communications

Connect the Controller Board to the

computer by using an Ethernet cable or a

Micro USB-B cable.

NOTE: Install USB drivers prior to

making USB connection (see Section

5.1).

EXIT

CONGRATULATIONS!

NetAXS-123 Startup Guide, Document 800-05780V2

5) Connecting to the Web Server

This section describes two configurations for connecting a computer

to the NetAXS-123 web server:

• Connecting via USB port.

• Connecting via Ethernet port.

NOTE: The panel that you are connecting to the computer is the

Gateway panel. DIP switch 6 on a Gateway panel must be set to ON

for a successful connection.

5.1 Connecting via USB Port

Warning: Do NOT connect the USB cable to the panel until AFTER

the drivers are installed.

Follow these steps to set up the NetAXS-123 USB connection. (This

procedure should be performed only once.)

1. Insert the NetAXS-123 Product CD into your Windows-based

computer. The NetAXS-123 product menu opens in the web

browser.

Note: If the product menu does not open automatically in your

browser, right click on the Start button and select Explore. In the

folder tree, find and click the CD drive that is reading the

NetAXS-123 Product CD.

2. Click Install USB Drivers on the product menu to start the

USB driver installation wizard.

3. Click Next to display the Ready to Install the Program

screen.

NetAXS-123 Startup Guide, Document 800-05780V2

NOTE: If confirmation dialog boxes pop up before or during the

installation, click the appropriate boxes to allow or approve the

installation.

4. Click Install to initiate the installation.

5. When the installation is complete, the final screen appears:

6. Click Finish.

7. Connect the computer to the NetAXS-123 controller with a

USB-A to Micro USB-B cable.

8. Turn on the power to the NetAXS-123 controller.

Proceed to Section 6, “Logging In to the System” on page 7.

NetAXS-123 Startup Guide, Document 800-05780V2

5.2 Connecting via Ethernet Port

You can connect the NetAXS-123 panel to a PC either directly with a

standard or cross-over ethernet cable as well as through an ethernet

switch with standard ethernet patch cables.

Perform the following steps:

1. In order to connect to the NetAXS-123 for the first time,

configure the computer's network connection:

a. Select Start > Settings > Control Panel.

b. Click Network and Dial-up Connections.

c. Identify your local Ethernet connection (commonly

labeled Local Area Connection), and right-click the

icon to display the Local Area Connection Properties

screen.

d. Highlight the Internet Protocol (TCP/IP) connection.

e. Click Properties to display your system’s current

Internet Protocol properties.

Important: Keep a record of your computer’s current network

configuration as it appears in this screen. You will need to re-instate

this configuration later.

f. Select "Use the following IP address."

g. Enter "192.168.1.10" in the IP address field.

h. Enter "255.255.255.0" in the Subnet mask field.

i. Click OK to accept the entries.

6) Logging In to the System

1. Open your internet browser (Internet Explorer and Mozilla

Firefox are supported).

2. Connect to the panel default address by entering the IP

address into the address box to reach the login screen:

• If using USB: https://192.168.2.150 (fixed address)

• If using IP/Ethernet: https://192.168.1.150 (default)

NOTE: When connecting to the web using a browser, you must use

https:// for a secure connection. The standard http:// that is the default

in most browsers will not work.

NOTE: The Ethernet IP address can be changed from the default

address for additional security or to align with an existing network.

Please refer to Appendix B for additional details.

3. Approve any security certificates by clicking “Continue to

this website”.

NOTE: If you receive a certificate error message, follow the

appropriate steps to accept and move on. These steps will differ from

one browser to another.

NetAXS-123 Startup Guide, Document 800-05780V2

4. Enter “admin” in the User Name field, and enter “admin” in

the Password field. Both the user name and password are

case-sensitive.

NOTE: For additional security, it is recommended that you change

your default user name (admin) and password (admin) to a new user

name and password. Refer to Appendix A for additional details.

5. Click Login to display the NetAXS-123 Main Window, also

referred to as the “Landing Page”.

7) System Configuration

The flowchart below outlines the basic steps necessary to successfully

program your NetAXS-123 panel.

Please follow the detailed steps in the next six sections to ensure the

successful programming of your NetAXS-123 panel. Start each of the

major steps on the Landing Page by selecting the link shown. Return

to the Landing Page by clicking on .

ASET COMMUNICATIONS

CONFIGURE DOOR(S)

ADD TIME ZONES

SET TIME

CREATE ACCESS LEVELS

ADD CARDS

Set the clock in the panel

to local time

Create and label reader (s), input and output devices

and assign time schedules to doors

Assign access levels to cards and then the card to

the card holder

Create time zones to be used to lock or unlock a door

by schedule as well as grant or deny access to a door

by a card holder

Defines which doors card holders can access and

when they can access them

Select communications

type (web or hosted, 485

or EVL)

These steps are for a

stand-alone gateway

controller. For details

regarding set up of

RS485 or EVL Loops,

please refer to

NetAXS-123 User

Guide.

NetAXS-123 Startup Guide, Document 800-05780V2

Step - Set Communications to “Web Mode”. Step - Set the time.

1. Under Communications,

click Host / Loop to display the Host/Loop

Communications tab.

2. Select None for Web Connection type. Select either EVL or

485 for communication type to downstream panels.

3. Click Submit to save the change.

4. Return to the Landing Page by clicking .

1. Under Time, click Current Time to display the Current

Time tab.

2. Set current local area time, date, and geographic time zone.

3. Click Submit to save the changes.

4. Return to the Landing Page by clicking .

NetAXS-123 Startup Guide, Document 800-05780V2

Step - Add time zones. Step - Door Configuration

- Door Configuration: Label Reader

1. Under Time, click Time Zones to display the Time Zones

tab.

2. Enter a Name for the time schedule.

3. Select Start Time and End Time. Select days of the week.

4. Click Add Time Zone to save the new time schedule.

5. Return to the Landing Page by clicking .

1. Under Configuration, click Door to display the Reader A

tab.

2. Enter a Name for Reader A.

3. Click Submit Changes to save the change.

Otros manuales para NetAXS-123

Tabla de contenidos

Otros manuales de Puerta de Honeywell

Honeywell

Honeywell 290092 Manual de usuario

Honeywell

Honeywell Notifier MODBUS-GW Manual de usuario

Honeywell

Honeywell SMX Manual de usuario

Honeywell

Honeywell LyricLCP300-L Manual de instalación y funcionamiento

Honeywell

Honeywell CIU 888 Manual de funcionamiento

Honeywell

Honeywell PEHA 940/8 DALI-G Manual de usuario

Honeywell

Honeywell Lyric LCP300-L Manual de usuario

Honeywell

Honeywell NOTIFIER ONYXWorks NFN Gateway Manual de usuario

Honeywell

Honeywell Lyric LCP300-L Manual de instalación y funcionamiento

Honeywell

Honeywell Notifier 002-467 Manual de usuario

Honeywell

Honeywell W8735G Manual de usuario

Honeywell

Honeywell ESSER IQ8Wireless Gateway Manual de usuario

Honeywell

Honeywell Wireless Network Master ETH/WIFI T2 Manual de usuario

Honeywell

Honeywell RedLINK THM6000R Manual de usuario

Honeywell

Honeywell Lyric LCP300-L Hoja de información del producto

Honeywell

Honeywell Experion PKS Manual de usuario

Honeywell

Honeywell NFS-3030 Manual de usuario

Honeywell

Honeywell NOTIFIER NFN-GW-PC-HNMF Manual de usuario

Honeywell

Honeywell CIU 888 Manual de usuario

Honeywell

Honeywell LGW1000 Manual de usuario

Honeywell

Honeywell GENT VIG-BNG Instrucciones de funcionamiento y mantenimiento

Honeywell

Honeywell HON-CGW-MBB Manual de usuario

Honeywell

Honeywell Evohome Manual de usuario

Honeywell

Honeywell ADPRO iFT Series Manual de usuario

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario