Honeywell E3Point Manual de usuario

E3Point®

User Manual

Standalone, Network, & Remote models

Gas Monitor

| Gas Detection

Go to French, Spanish Versions 1998M0972 Rev 01

E3Point Gas Monitor Technical Manual i

Symbol Denitions

Symbol Definitions

The following table lists the symbols used in this document to denote

certain conditions:

Symbol Definition

ATTENTION: Identifies information that requires special

consideration.

TIP: Identifies advice or hints for the user, often in terms

of performing a task.

REFERENCE _ INTERNAL: Identifies an additional source

of information within the bookset.

CAUTION

Indicates a situation which, if not avoided, may result in

equipment or work (data) on the system being damaged

or lost, or may result in the inability to properly operate

the process.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury. It may also be used to alert against unsafe

practices.

CAUTION: Symbol on the equipment refers the user to

the product manual for additional information. The symbol

appears next to required information in the manual.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, can result in serious injury or death.

WARNING symbol on the equipment refers the user to

the product manual for additional information. The symbol

appears next to required information in the manual.

E3Point Gas Monitor Technical Manual iii

IMPORTANT NOTICE

System Validation Test or Commissioning of the gas detection system is

not complete until it is tested to verify that it is functioning according to

its design objectives or specifications.

Validation includes, but is not limited to:

•Verication tests of the functions of each component in the individual

system architecture.

•Verication that all inputs to the system result in the correct outputs.

•Verication that, where required, a back-up power supply system

is in place.

•Verication that all personnel who will be working with and/or

affected by the system have received proper instruction on use

and purpose.

iv E3Point Gas Monitor Technical Manual

Table of Contents

Symbol Definitions ...............................................................................i

IMPORTANT NOTICE.......................................................................... iii

Introduction..........................................................................................1

Restricted Materials Table for China RoHS..........................................1

Warnings and Cautions.......................................................................2

Installation............................................................................................4

Locating the Sensor............................................................................4

Installation Height ..................................................................5

Wall Mounting for Standalone/Network monitor .....................5

Mounting for Remote monitor .............................................................7

Duct Mounting....................................................................................8

Special Duct Mount Installation..............................................8

Wiring..................................................................................................10

Guidelines.........................................................................................10

Wiring Standalone monitor ..................................................10

Connecting a Remote monitor to the Standalone monitor....12

Wiring Network Monitors .....................................................12

Installation Test..................................................................................13

Standalone Model Operation ..........................................................14

Start-Up Procedure ..........................................................................14

Network Model Operation ...............................................................15

User Interface ...................................................................................16

Monitor Operation .............................................................................17

Using the Programming Menus.........................................................17

Main Menu Options ..........................................................................17

Password Menu ..................................................................18

Network Menu.....................................................................18

Display Menu.......................................................................19

Restore Menu......................................................................19

Temp Menu .........................................................................20

Set Zero Menu.....................................................................21

Set Span menu ...................................................................22

TestMode Menu...................................................................23

E3Point Gas Monitor Technical Manual v

Table of Contents

Memory Menu .....................................................................23

Quit Menu ...........................................................................23

Model Specific Menu Options...........................................................24

Standalone Model Relay Menu ............................................24

Standalone Model Buzzer Menu..........................................25

Standalone Model Alarm Menu............................................25

Network Relay Menu ...........................................................27

Network Model Buzzer Menu ..............................................28

Network Model Alarm Menu ................................................29

Remote Sensor..................................................................................31

Description .......................................................................................31

Safety Information ...............................................................31

Specifications ....................................................................................32

General Technical Specifications.......................................................32

Detection Ranges and Alarm Levels..................................................33

Sensor Over Range ..........................................................................33

Periodic Inspection and Maintenance ...............................................35

Maintenance........................................................................35

Sensor Life Span.................................................................35

Troubleshooting.................................................................................36

Annex A - BACnet and Modbus Objects on E3Point Network.......39

BACnet Configuration.......................................................................39

BACnet Objects Descriptions ..............................................39

Modbus Registers Description..........................................................40

BACnet Protocol Implementation Conformance Statement.........40

Limited Warranty ...............................................................................45

Limited Warranty...............................................................................45

Re-Stocking Policy ...........................................................................45

Exclusions ........................................................................................45

Warranty Limitation and Exclusion ....................................................46

Disclaimer of Unstated Warranties ...................................................46

Limitation of Liability .........................................................................46

E3Point Gas Monitor Technical Manual

Introduction

E3Point derives its name from: Energy Management, Efficiency, and Economic

value in gas detection.

E3Point is an important part of toxic or combustible gas detection system that

combines a gas sensor (electrochemical or catalytic type), a control unit, and a set

of outputs (such as 4-20 mA current loop, buzzer and relays). The polycarbonate

housing is resistant to rust, dents and corrosion.

There are 3 monitor models in the E3Point family: Standalone, Remote and

Network. The Standalone monitor provides the full control unit, with a built

in sensor and is capable of accepting one additional Remote sensor. This

configuration allows the E3Point to detect two gases in two separate locations.

The E3Point Network platform supports different protocols over an RS-485 link,

such as Modbus or BacNet MS/TP master. It is well suited for commercial use in

parking garages and mechanical rooms. It is intended for connection to the 301-C

or AA96D series contollers.

Installation is both economical and efficient because it is achieved in 3 easy steps

(mounting, wiring and power-up). Units are shipped with a Quick Start Guide to

support proper installation.

Restricted Materials Table for China RoHS

E3Point Gas Monitor Technical Manual

Warnings and Cautions

Warnings

•Power to the E3Point monitor must be off during installation and when

installing the sensor cartridge.

•The installer must be grounded for ESD protection while handling the PC

board (PCBA) and during installation of the monitor.

•Follow all local codes when installing the monitor.

•Operate, service, and use the monitor only as specified in the quick start

guide and this technical manual. Failure to do so may impair the protection

the monitor is designed to provide and may also void the warranty. The

manual is available on the Honeywell Analytics website. You may scan the

QR code below for easy access to product information:

www.honeywellanalytics.com

www.honeywell.com

•Calibration, set-up, and test modes are intended for use by trained personnel

and service engineers only. Access to these modes is passcode protected.

•Follow local and site procedures when working with this monitor. If applicable,

verify that the associated control panel is inhibited in order to prevent false

alarms during installation. The procedures in the quick start guide and the

product’s technical manual must be followed carefully and performed only

by trained personnel and service engineers.

•Use only accessories and parts meeting or exceeding Honeywell Analytics’

specifications.

•Some monitors require warm-up time. See the appropriate sections in this

technical manual for specific information.

•Ensure that the monitor screen is free of dirt and debris, and do not cover

or paint over the monitor screen.

•Do not expose the monitor to electrical shock and/or continuous mechanical

shock.

The warranty will be voided if the customer or any unauthorized service

personnel attempt to repair the monitor

E3Point Gas Monitor Technical Manual

Warnings and Cautions

Cautions

•The E3Point monitor must be installed only by trained personnel and service

engineers in accordance with local codes.

•The safety of any system incorporating the E3Point monitor is the responsibility

of the assembler of the system.

•Protect the monitor from water, wash-down, and excessive humidity.

•To prevent electrical interference, keep the monitor and wire runs away from

mercury vapor lights, variable speed drives, and radio repeaters.

•Protect the monitor from physical damage (fork lifts, etc.).

•Do not mount the monitor over a door in a refrigerated area.

•For critical locations, more than one monitor should be installed in each room.

•Never mount the sensor flat on a ceiling.

•Never mount the sensor on a vibrating surface.

E3Point Gas Monitor Technical Manual

Installation

WARNING: Some materials such as, but not limited to, tetraethyl lead,

silicones, some sulfur, phosphorus, and chlorinated compounds, may have a

poisoning effect resulting in a loss of sensitivity. Avoid installing the monitor

in areas where these materials may be present.

Locating the Sensor

Considerations in locating the monitor

Instalation Height:

•Fastest Possible Leak Detection – Mount the monitor near the

potential leak sources

- One monitor should be located in close proximity to each point where

an emission is likely to occur

- Indicated concentration may not be representative of personnel

exposure

- Easy access for the required calibration and maintenance could be

compromised

•Personnel Protection

– Mount the sensor at the installation heights shown in the table below

–Gas is detected where it is accumulated – which may not be detected

at the leak source.

Air Currents: If there are fans, wind, or other source of air movement, gases may

tend to rise or collect in certain areas of a facility. The local air currents should be

assessed to aid in selecting the sensor location. Air convection can often be more

important in determining gas concentration areas than factors of Vapor Density.

Gas Emission Sources: As a rule, at least one sensor should be located in close

proximity to each point where an emission is likely to occur.

CAUTION: Because each sensor can only “report” what it is

detected at the place it is installed at a specific moment, it

is very important that the sensor be located where leaks

are most likely to occur.

Otros manuales para E3Point

Tabla de contenidos

Idiomas:

Otros manuales de Detector de gas de Honeywell

Honeywell

Honeywell 201T Manual de usuario

Honeywell

Honeywell BW Technologies Clip Real Time Manual de usuario

Honeywell

Honeywell BW GasAlertMicroClip XT Manual de usuario

Honeywell

Honeywell Midas Manual de usuario

Honeywell

Honeywell AreaRAE Plus Manual de usuario

Honeywell

Honeywell BW Icon Manual de usuario

Honeywell

Honeywell SEARCHLINE EXCEL PLUS Manual de usuario

Honeywell

Honeywell JTQJ-BF-01LM/BW Manual de usuario

Honeywell

Honeywell Searchpoint Optima Plus Guía del usuario

Honeywell

Honeywell BW Icon Manual de usuario

Honeywell

Honeywell GasAlertMicro 5 Series Manual de usuario

Honeywell

Honeywell RAEGuard Lite Manual de usuario

Honeywell

Honeywell SPM Flex Manual de usuario

Honeywell

Honeywell Notifier VGS-EXP Manual de usuario

Honeywell

Honeywell HON COCON 13 Manual de usuario

Honeywell

Honeywell Touchpoint Plus Nota de versión

Honeywell

Honeywell Sensepoint XCD Manual de uso y cuidado

Honeywell

Honeywell BW Technologies GasAlert MicroClip XT Manual de usuario

Honeywell

Honeywell Touchpoint 4 Manual de usuario

Honeywell

Honeywell XP Series Instrucciones de uso

Honeywell

Honeywell BW MaxXT II Manual de usuario

Honeywell

Honeywell Signalpoint Pro Manual de usuario

Honeywell

Honeywell Sensepoint XCL Manual de usuario

Honeywell

Honeywell Apex Nota de versión

Manuales populares de Detector de gas de otras marcas

Macurco

Macurco GD-6 Manual de usuario

Evikon

Evikon E2632 Manual de usuario

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Manual de usuario

MSA

MSA altair 5 Manual de usuario

DOD Technologies

DOD Technologies ChemLogic CL96 Manual de usuario

DEGA

DEGA NS III LCD Series Manual de usuario

RKI Instruments

RKI Instruments 35-3001A-08-01 Manual de usuario

PEMTECH

PEMTECH PT2008 Series Manual de usuario

Coster

Coster RGS 328 Manual de usuario

Sygonix

Sygonix 2483186 Manual de usuario

Perry

Perry 1GA 50917MET/P Manual de usuario

isweek

isweek AS8900 Manual de usuario

Oldham

Oldham OLC 10 Manual de usuario

Wizmart

Wizmart NB983 Manual de usuario

Beacon

Beacon MEGA Manual

RKI

RKI GX-6000 Manual de usuario

Dräger

Dräger PIR 7000 Manual de usuario

GDS

GDS GASMAX EC Manual de usuario