Honeywell UDC3500 Manual de usuario

01/06 Kit Instruction 51-52-33-153 1

UDC3500 Universal Digital Controller

Printed Wiring Board Replacements

Instruction 51-52-33-153

•Kit contents This kit contains one of the following replacement Printed Wiring Boards:

•UDC3500 MCU/Input Board – Part No. 51452828-502

•UDC3500 Power 90-264 Vac Board – Part No. 51452831-501

•UDC3500 Power 24 Vac/dc Board – Part No. 50006376-501

•UDC3500 Display/Keyboard – Part No. 51452845-501

•UDC3500 Dual Relay Board – Part No. 51452807-501

•UDC3500 Optional Input Board – Part No. 51452825-501

•UDC3500 Third Current Output Board – Part No. 51452834-501

•UDC3500 Aux Out/Digital Inputs/RS-485 – Part No. 51452837-502

•UDC3500 Digital Inputs/Ethernet Board – Part No. 51452840-501

•UDC3500 Optional Relay Board – Part No. 51452843-501

Equipment needed • Small flat-bladed screwdriver

• Small pliers

Procedures The procedure tables that follow list the steps required to replace the old

Printed Wiring Board in your controller with the one supplied in this kit.

Continued on next page

2 Kit Instruction 51-52-33-153 01/06

Replacement Instruction, Continued

Chassis removal

Table 1 How to Remove the Chassis

Step Action

1 Remove any screws in the front face.

2 Insert a flat-bladed screwdriver into the tabs of the case as shown in

Figure 1 and pry chassis forward slightly until the chassis connectors

separate from the back of the case.

3 Grasp the bezel and pull the chassis out of the case.

Figure 1 Chassis Removal

Using a thin screwdriver, gently twist the screwdriver to pry the side tabs from the front

face. Pry just enough to release it, otherwise you’ll bend or break the tab. If you break or

bend the tab and can’t reattach the front snugly, you’ll need to reattach the front using the 4

NEMA4 screws provided.

Continued on next page

Insert thin screwdriver under

tabs and twist slightly and

gently to disengage front

01/06 Kit Instruction 51-52-33-153 3

Replacement Instruction, Continued

Printed wiring board

removal Table 2 How to Remove the Printed Wiring Boards from the Chassis

Step Action

1 Remove the chassis from the case as shown in Figure 1.

2 Separate the chassis frame at the release points shown in Figure 2

and wiggle each printed wiring board out of its socket on the

display/keyboard assembly. Pull all boards out of the chassis.

3 Remove the wire connectors from plug WG1 on Power/Output

Board. Slide a small screwdriver under the connectors and lift the

release.

4 Lay the printed wiring boards flat on a static-free surface. Use

Figures 3 through 6 to locate the board being replaced.

Figure 2 Removing the Printed Wiring Boards

Printed wiring board

identification Figure 3 Major Printed Wiring Board Identification

Continued on next page

Release points (top and bottom)

Power / Out

ut Bd.

Auxiliary output / Digital

Inputs / Communication Bd.

MCU / Input Board

tional Rela

s Bd.

WG1 and Wires

Display / Keyboard

4 Kit Instruction 51-52-33-153 01/06

Replacement Instruction, Continued

Printed wiring board

identification Figure 4 Optional Input Printed Wiring Board Identification

Printed wiring board

identification Figure 5 Third Current Output Printed Wiring Board Identification

Printed wiring board

identification Figure 6 Dual Relay Printed Wiring Board Identification

The Dual Relay Board would be in place of the Third Current Output Board shown

in Figure 5.

Continued on next page

Third Current Output

Power / Output Board

Second Input Board

Third Input Board

Battery

MCU / Input Board

01/06 Kit Instruction 51-52-33-153 5

Replacement Instruction, Continued

Replacement

procedure

Table 3 Board Replacement Procedure

Step Action

1 Identify the Board to be replaced from Figures 3 through 6.

Replace that board with the new one.

2 The small boards shown in Figures 4, 5 and 6 (Optional Input,

Third Current Output and Dual Relay Output) are held onto the

major boards with posts. If replacing one of these small boards or

the major boards they are attached to, then locate the ends of the

posts on the back side of the Major Board.

3 Use small pliers and squeeze the ends of each post together and

push it up through the board.

4 Remove the small boards. Replace as needed. Posts must be

pushed all the way through the Major Board until they snap into

place in order to ensure a good electrical and mechanical

connection.

5 The Third Current Output and Dual Relay Output boards must be

fully seated into the socket in order to ensure a good electrical and

mechanical connection.

Table 4 Chassis Reassembly Procedure

Step Action

1 Install the Display/Keyboard into the chassis. There are four slots

cut in the Bezel. Place the bottom of the Display/Keyboard into the

slots and then press the top of the display in until it snaps in place

in the slots. See Figure 7.

2 Assemble the Optional Relay board onto the Power/Output Board.

Start these boards as a pair into the chassis groves and carefully

push them in until they snap into place. See Figure 8.

3 Assemble the Communications board over the capacitors on the

MCU/Input board. Start these boards as a pair into the chassis

groves and carefully push them in until they snap into place. See

Figure 9.

4 Make sure the connections to the display/keyboard assembly are

made and that the release points on the chassis snap into place on

the printed wiring boards. See Figure 10.

5 Reinstall the WG wires onto the Power/Output Board. See Figure

11.

6 Reinstall the chassis into the case.

Continued on next page

6 Kit Instruction 51-52-33-153 01/06

Replacement Instruction, Continued

Chassis Reassembly Figure 7 Display / Keyboard

There are four slots cut in the Bezel which fit four tabs on the Display / Keyboard. Place the bottom of the

Display / Keyboard into the bottom chassis slots and press the top of the display in until it snaps into place in

the top chassis slots.

Chassis Reassembly Figure 8 Optional Relay and Power/Output Board

The P15 connector on the Optional Relay board plugs into J15 on the Power/Output board. Insert

these boards as an assembly into the Chassis. Start them in the chassis groves and carefully push

them in until they snap into place.

Continued on next page

P15

J15

4 Slots

Top of Display

otto

f Di

Tabs

01/06 Kit Instruction 51-52-33-153 7

Replacement Instruction, Continued

Chassis Reassembly Figure 9 Communications and MCU/Input Board

Place the Communications board over the Capacitors on the Optional Input Boards. Insert these boards as an

assembly into the Chassis. Start them in the chassis groves and carefully push them in until they snap into

place.

Chassis Reassembly Figure 10 Chassis Assembly

Make certain that the four larger boards are properly snapped into the top and bottom of the Chassis.

Continued on next page

Boards should snap into place

8 Kit Instruction 51-52-33-153 01/06

Replacement Instruction, Continued

Chassis Reassembly Figure 11 WG1 Ground Wires

Plug the two ground wires onto the WG1 posts on the Power/Output Board. Wires must routed through the

board notches in order to ensure that they do not interfere when the chassis is plugged into the case.

Ethernet Replacement

Table 5 Ethernet Board MAC and IP Information

Step Action

1 Replacement Ethernet Boards have a label on them which show

their MAC address. This is a unique value for each board.

2 All replacement Ethernet Boards have their IP address set to

10.0.0.2 as shipped from the Factory.

Plug the Ground

Wires onto the

WG1 Posts

Route Ground

Wires throu

h the

Board notches

Otros manuales para UDC3500

Tabla de contenidos

Otros manuales de Controladores de Honeywell

Honeywell

Honeywell N20 Series Manual de usuario

Honeywell

Honeywell SLATE Series Manual de usuario

Honeywell

Honeywell HC900 Guía del usuario

Honeywell

Honeywell HVC0001 Manual de usuario

Honeywell

Honeywell DC1010 Guía de inicio rápido

Honeywell

Honeywell VS820 POWERPILE Guía del usuario

Honeywell

Honeywell RM7800E Manual de usuario

Honeywell

Honeywell CD3000M-3PH Manual de usuario

Honeywell

Honeywell VC6613AJ1000 Manual de usuario

Honeywell

Honeywell D6 PRO Manual de usuario

Honeywell

Honeywell AUTOMATIC CONTROL Manual de instalación y operación

Honeywell

Honeywell HJK7000 UltraKey Plus Manual de instrucciones

Honeywell

Honeywell ML8824 Series Manual del operador

Honeywell

Honeywell 10260S Series Manual de usuario

Honeywell

Honeywell UDC1200 MICRO-PRO Guía del usuario

Honeywell

Honeywell ML7999A Manual de operación

Honeywell

Honeywell HR 40 Manual de usuario

Honeywell

Honeywell 190797-YAD Manual de usuario

Honeywell

Honeywell V9055A Manual de usuario

Honeywell

Honeywell DB7110U1000 Manual de usuario

Honeywell

Honeywell EDC 200 Series Manual de usuario

Honeywell

Honeywell HC900 Manual de usuario

Honeywell

Honeywell IPC5000 Manual de usuario

Honeywell

Honeywell SUPER TRADELINE S8610U Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario