Honeywell UDC 6300 Guía

11/99 Kit Instruction 51-52-33-85C 1 of 5

UDC 6300 Process Controller

Upgrade PROM

Replacement Instruction

Document Number Form: 51-52-33-85C

Effective: 11/99

Supersedes: 3/99

Kit contents This kit contains one of the following Upgrade PROMs

Description Part Number

Adaptive Tune 51450900-501

Adaptive Tune + Math 51450900-502

Adaptive Tune + 2 Loops + Cascade 51450900-503

All Options 51450900-504

TPS Integration 51309350-501

Modbus RTU 51309350-502

Basic PROM 51309181-501

Equipment needed

• Phillips Head Screwdriver

• Flat Bladed Screwdriver

• Small Pliers

Continued on next page

2 of 5 Kit Instruction 51-52-33-85C 11/99

Replacement Instruction, Continued

How to remove the

chassis Refer to Figure 1 for reference and follow the procedure listed in Table 1.

Table 1 How to Remove the Chassis

Step Action

1 Pull down the flap covering the front screw and loosen the screw.

2 Grasp the bezel and pull the chassis out of the case.

Figure 1 Chassis Removal

Rear of case

23045

Front Screw

Bezel/Keyboard/Display Assembly

Continued on next page

11/99 Kit Instruction 51-52-33-85C 3 of 5

Replacement Instruction, Continued

How to install the

PROM

Table 1 How to Install the PROM

Step Action

1 The PROM is located on the MCU/Input printed wiring board at

location U109. See Figure 2 for location.

If a Communications Board is not present:

2 Lay the chassis on its left side on a non conductive surface

3 Insert a small screwdriver under the PROM and lift up to remove.

4 Orient the PROM to the socket and press into place.

5 Return the chassis to the case and configure the controller to include

the new features.

If a Communications Board is present:

6 Go to Table 2.

Figure 2 Parts Identification

23044

Rear of case

Front Screw

Communications

PWB

MCU/Input PWB

Option Input PWB

Power/ DIO PWB

Bezel/Keyboard/

Display Assembly

SpacerInterconnect

Interconnect

PWB Mounting Screws (4)

Cable Assembly

Power/DIO PWB

to Option Input Board

Mounting Screw

Chassis

EEPROM

at U106

PROM

(on MCU/Inputs

board at U109)

Continued on next page

4 of 5 Kit Instruction 51-52-33-85C 11/99

Replacement Instruction, Continued

How to remove the

Bezel/Keyboard/

Display assembly

In order to access the PROM if your controller has a Communications

Board, you must remove the Bezel/Keyboard/Display assembly from the

chassis and access the printed wiring boards.

The procedure in Table 2 lists the steps required to remove the

Bezel/Keyboard/Display assembly.

Table 2 How to Remove the Bezel/Keyboard/Display Assembly

Step Action

1 Remove the two screws on the bottom of the chassis frame that hold

the Bezel/Keyboard/Display assembly in place on the chassis frame.

Refer to Figure 2 for reference.

2 Lift the two retainers slightly away from the MCU/Input board notch

and the Power/DIO board on the opposite side as shown below.

The Bezel/Keyboard/Display board assembly will come away in one

piece.

Power/DIO

Board

MCU/Input

Board

Lift

retainers

here

Top of

rubber bezel

UDC6300

3 Install the PROM supplied in this kit.

See Table 3.

4 Reinstall the Bezel/Keyboard/Display assembly.

CAUTION Be careful to align the pins on the display board with

the mating connector P9 on the MCU/Input board.

5 Reattach the bezel assembly to the chassis with the screws

previously removed.

Continued on next page

11/99 Kit Instruction 51-52-33-85C 5 of 5

Replacement Instruction, Continued

How to install the

PROM Follow the procedure in Table 3 to access the PROM.

Table 3 Access the PROM

Step Action

1 Remove the four screws (two on each side) that hold the two main

printed wiring boards onto the chassis (See Figure 2 for location)

2 Use pliers to squeeze the ends of the spacer and push it through

the Power/ Digital I/O PWB. (See Figure 2 for location of spacer)

3 Gently pull the MCU/Inputs and the Power/DIO boards apart out of

the top and bottom interconnectors and lay the boards flat on a

non-conductive surface. (See figure 3).

4 Identify the Communications Option board (If present) and remove

the two screws that hold it onto the MCU/Inputs PWB.

5 Figure 3 identifies the location of the PROM.

6 Insert a small screwdriver under the PROM and lift up to remove.

7 Orient the PROM to the socket and press into place.

8 Reassemble the Communications Option PWB to the MCU/Inputs

PWB.

9 Reassemble the interconnects to the MCU/Inputs board and

reassemble the boards reversing the procedure above.

10 Reattach the Bezel/Keyboard/Display board assembly as listed in

Table 2 - steps 4 and 5.

11 Return the chassis to the case and configure the controller to

include the new features.

Figure 3 Printed Wiring Board Identification

Communications

Option Board

Option

Input Board

Power / DIO Board

MCU/Inputs

Board

J14

P14

U109

PROM Location

Pin 1

23046

Tabla de contenidos

Otros manuales de Controladores de Honeywell

Honeywell

Honeywell MN6105VAV Manual de usuario

Honeywell

Honeywell ML7999A Manual de operación

Honeywell

Honeywell VBN2 Manual de usuario

Honeywell

Honeywell PRO22IC Manual de usuario

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell CN100 Manual técnico

Honeywell

Honeywell P906C Manual de operación

Honeywell

Honeywell ML6420 Manual de operación

Honeywell

Honeywell PCR-300 Manual de usuario

Honeywell

Honeywell WEB/CP-202-XPR Manual de usuario

Honeywell

Honeywell VR4304 Series Manual de usuario

Honeywell

Honeywell 10260S series Guía

Honeywell

Honeywell HEGSA002 Manual de usuario

Honeywell

Honeywell INCOMM L510 Manual de usuario

Honeywell

Honeywell ML6275 Manual de operación

Honeywell

Honeywell R7426A Manual de usuario

Honeywell

Honeywell N20010 Manual de usuario

Honeywell

Honeywell touchpoint Pro Manual de usuario

Honeywell

Honeywell ML7421A1032 Manual de operación

Honeywell

Honeywell C Manual de usuario

Honeywell

Honeywell DeltaNet R7515A Manual de usuario

Honeywell

Honeywell THP9045A Manual de usuario

Honeywell

Honeywell Z74S-AN Manual de usuario

Honeywell

Honeywell V800 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario